Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1655/37    Driver Side Seat Belt Buckle Switch Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat belt buckle switch LH circuit consists of the center airbag sensor assembly and the front seat inner belt assembly LH (seat belt buckle switch LH).
DTC B1655/37 is set when a malfunction is detected in the seat belt buckle switch (driver seat side) circuit.

DTC No.
DTC Detections Conditions
Trouble Areas
B1655/37
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch (Driver seat side) circuit for 2 seconds
  2. Front seat inner belt assembly LH malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. No. 1 seat wire (*1)
  3. No. 2 seat wire (*1)
  4. Front seat inner belt assembly LH (Seat belt buckle switch LH)
  5. Center airbag sensor assembly
*1: Bench seat

WIRING DIAGRAM


H101960E01


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch to the LOCK position.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  6. (f) Disconnect the connector from the front seat airbag assembly LH.
  7. (g) Disconnect the connector from the front seat airbag assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  1. (h) Disconnect the connector from the curtain shield airbag assembly LH.
  2. (i) Disconnect the connector from the curtain shield airbag assembly RH.
  3. (j) Disconnect the connector from the front seat outer belt assembly LH.
  4. (k) Disconnect the connector from the front seat outer belt assembly RH.
1.CHECK DTC


    H101961E01
  1. Turn the ignition switch to the ON position.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

HINT:
DTCs other than B1655/37 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front seat inner belt assembly LH.



NG
CONNECT CONNECTORS
OK


3.CHECK CONNECTORS
  1. Check that the connectors (on the center airbag sensor assembly side and front seat inner belt assembly LH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.

    Condition
    Proceed to
    Normal (separate seat)
    A
    Normal (bench seat)
    B
    Abnormal
    C



B
Go to step 9

C
REPAIR OR REPLACE WIRE HARNESS
A


4.CHECK DRIVER SIDE SEAT BELT BUCKLE SWITCH CIRCUIT (FOR OPEN)


    H101855E01
  1. Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt assembly LH.

  1. Using a service wire, connect F20-2 and F20-1 of connector C.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-11 (DBE+) - A22-12 (DBE-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


5.CHECK DRIVER SIDE SEAT BELT BUCKLE SWITCH CIRCUIT (FOR SHORT)


    H100839E05
  1. Disconnect the service wire from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-11 (DBE+) - A22-12 (DBE-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


6.CHECK DRIVER SIDE SEAT BELT BUCKLE SWITCH CIRCUIT (TO B+)


    H100839E05
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A22-11 (DBE+) - Body ground
    Ignition switch ON
    Below 1 V
    A22-12 (DBE-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


7.CHECK DRIVER SIDE SEAT BELT BUCKLE SWITCH CIRCUIT (TO GROUND)


    H100839E05
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-11 (DBE+) - Body ground
    Always
    1 MΩ or Higher
    A22-12 (DBE-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


8.CHECK FRONT SEAT INNER BELT ASSEMBLY LH


    H100892E02
  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the connector to the front seat inner belt assembly LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

HINT:
DTCs other than B1655/37 may be output at this time, but they are not related to this check.



NG
Go to step 22
OK

USE SIMULATION METHOD TO CHECK 

9.CHECK DRIVER SIDE SEAT BELT BUCKLE SWITCH CIRCUIT (FOR OPEN)


    H101962E01
  1. Disconnect the connectors from the center airbag sensor assembly and the seat inner belt assembly LH.

  1. Using a service wire, connect F23-1 and F23-2 of connector G.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-11 (DBE+) - A22-12 (DBE-)
    Always
    Below 1 Ω



NG
Go to step 14
OK


10.CHECK DRIVER SIDE SEAT BELT BUCKLE SWITCH CIRCUIT (FOR SHORT)


    H101963E01
  1. Disconnect the service wire from connector G.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-11 (DBE+) - A22-12 (DBE-)
    Always
    1 MΩ or Higher



NG
Go to step 15
OK


11.CHECK DRIVER SIDE SEAT BELT BUCKLE SWITCH CIRCUIT (TO B+)


    H101963E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A22-11 (DBE+) - Body ground
    Ignition switch ON
    Below 1 V
    A22-12 (DBE-) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 16
OK


12.CHECK DRIVER SIDE SEAT BELT BUCKLE SWITCH CIRCUIT (TO GROUND)


    H101963E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-11 (DBE+) - Body ground
    Always
    1 MΩ or Higher
    A22-12 (DBE-) - Body ground
    Always
    1 MΩ or Higher



NG
Go to step 17
OK


13.CHECK FRONT SEAT INNER BELT ASSEMBLY LH


    H101964E01
  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the connectors to the front seat inner belt assembly LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

HINT:
DTCs other than B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 22
OK

USE SIMULATION METHOD TO CHECK 

14.CHECK DRIVER SIDE SEAT BELT BUCKLE SWITCH CIRCUIT (FOR OPEN)


    H101965E01
  1. Disconnect the No. 2 seat wire connector from the No. 2 floor wire.

HINT:
The service wire has already been inserted into connector G.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BK1-2 (DBE+) - BK1-1 (DBE-)
    Always
    Below 1 Ω



NG
Go to step 18
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

15.CHECK DRIVER SIDE SEAT BELT BUCKLE SWITCH CIRCUIT (FOR SHORT)


    H101966E01
  1. Disconnect the No. 2 seat wire connector from the No. 2 floor wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BK1-2 (DBE+) - BK1-1 (DBE-)
    Always
    1 MΩ or Higher



NG
Go to step 19
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

16.CHECK DRIVER SIDE SEAT BELT BUCKLE SWITCH CIRCUIT (TO B+)


    H101966E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the No. 2 seat wire connector from the No. 2 floor wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    BK1-2 (DBE+) - Body ground
    Ignition switch ON
    Below 1 V
    BK1-1 (DBE-) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 20
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

17.CHECK DRIVER SIDE SEAT BELT BUCKLE SWITCH CIRCUIT (TO GROUND)


    H101966E01
  1. Disconnect the No. 2 seat wire connector from the No. 2 floor wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BK1-2 (DBE+) - Body ground
    Always
    1 MΩ or Higher
    BK1-1 (DBE-) - Body ground
    Always
    1 MΩ or Higher



NG
Go to step 21
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

18.CHECK NO. 1 SEAT WIRE (FRO OPEN)


    H101967E01
  1. Disconnect the No. 2 seat wire connector from the No. 2 seat wire.

HINT:
The service wire has already been inserted into connector G.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BL1-3 (DBE+) - BL1-4 (DBE-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE NO. 2 SEAT WIRE 

19.CHECK NO. 1 SEAT WIRE (FOR SHORT)


    H101968E01
  1. Disconnect the No. 1 seat wire connector from the No. 2 seat wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BL1-3 (DBE+) - BL1-4 (DBE-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE NO. 2 SEAT WIRE 

20.CHECK NO. 1 SEAT WIRE (TO B+)


    H101968E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the No. 1 seat wire connector from the No. 2 seat wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    BL1-3 (DBE+) - Body ground
    Ignition switch ON
    Below 1 V
    BL1-4 (DBE-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE NO. 2 SEAT WIRE 

21.CHECK NO. 1 SEAT WIRE (TO GROUND)


    H101968E01
  1. Disconnect the No. 1 seat wire connector from the No. 2 seat wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BL1-3 (DBE+) - Body ground
    Always
    1 MΩ or Higher
    BL1-4 (DBE-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE NO. 2 SEAT WIRE 

22.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front seat inner belt assembly LH (Click here or Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.


NEXT


23.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    H101961E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

HINT:
DTCs other than B1655/37 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

END