Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1660/43    Passenger Airbag ON / OFF Indicator Circuit Malfunction

for Preparation Click here


DESCRIPTION

The passenger airbag ON/OFF indicator light circuit consists of the center airbag sensor assembly and the passenger seat belt warning light assembly.
This circuit indicates the operation condition of the front passenger airbag assembly, the front seat airbag assembly RH and passenger side seat belt pretensioner.
DTC B1660/43 is set when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No.
DTC Detections Conditions
Trouble Areas
B1660/43
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the passenger airbag ON/OFF indicator circuit for 2 seconds
  2. Passenger seat belt warning lamp assembly malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Hazard warning signal switch assembly (Passenger airbag ON/OFF indicator)
  3. Center airbag sensor assembly

WIRING DIAGRAM


H101811E01


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch to the LOCK position.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  6. (f) Disconnect the connector from the front seat airbag assembly LH.
  7. (g) Disconnect the connector from the front seat airbag assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  1. (h) Disconnect the connector from the curtain shield airbag assembly LH.
  2. (i) Disconnect the connector from the curtain shield airbag assembly RH.
  3. (j) Disconnect the connector from the front seat outer belt assembly LH.
  4. (k) Disconnect the connector from the front seat outer belt assembly RH.
1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR OPERATION
  1. Turn the ignition switch to the ON position.

  1. Check the passenger airbag ON/OFF indicator operation.

HINT:
Refer to the normal condition of the passenger airbag ON/OFF indicator (Click here or Click here).


H100194E01

Result:
ON/OFF Indicator Illumination
Proceed to
Always ON
A
OFF
B



B
Go to step 9
A


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the hazard warning signal switch assembly.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3.CHECK CONNECTORS
  1. Check that the connectors (on the center airbag sensor assembly side and passenger seat belt warning light assembly side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


4.CHECK HAZARD WARNING SIGNAL SWITCH ASSEMBLY (PASSENGER AIRBAG ON/OFF INDICATOR)


    H046083E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Check the passenger airbag ON/OFF indicator operation.

    OK:
    Neither ON nor OFF passenger airbag ON/OFF indicator comes on.



OK
Go to step 17
NG


5.CHECK INSTRUMENT PANEL WIRE (TO GROUND)


    H100896E09
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the passenger seat belt warning light assembly.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-17 (P-AB) - Body ground
    Always
    1 MΩ or Higher
    A21-23 (PAON) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


6.CHECK INSTRUMENT PANEL WIRE (FOR SHORT)


    H100896E09
  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-17 (P-AB) - A21-23 (PAON)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


7.CHECK INSTRUMENT PANEL WIRE (FOR OPEN)


    H101926E01
  1. Using a service wire, connect H7-5 (SW-) and H7-12 (AIR) of connector C.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-23 (PAON) - A21-17 (P-AB)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


8.CHECK INSTRUMENT PANEL WIRE (TO B+)


    H100896E09
  1. Disconnect the service wire from connector C.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A21-23 (PAON) - Body ground
    Ignition switch ON
    Below 1 V
    A21-17 (P-AB) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY 

9.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the hazard warning signal switch assembly.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


10.CHECK CONNECTORS
  1. Check that the connectors (on the center airbag sensor assembly side and passenger seat belt warning light assembly side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


11.CHECK INSTRUMENT PANEL WIRE (TO GROUND)


    H100896E09
  1. Disconnect the connector from the passenger seat belt warning light assembly.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-17 (P-AB) - Body ground
    Always
    1 MΩ or Higher
    A21-23 (PAON) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


12.CHECK INSTRUMENT PANEL WIRE (FOR SHORT)


    H100896E09
  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-17 (P-AB) - A21-23 (PAON)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


13.CHECK INSTRUMENT PANEL WIRE (FOR OPEN)


    H101926E01
  1. Using a service wire, connect H7-5 (SW-) and H7-12 (AIR) of connector C.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-23 (PAON) - A21-17 (P-AB)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


14.CHECK INSTRUMENT PANEL WIRE (TO B+)


    H100896E09
  1. Disconnect the service wire from connector C.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A21-23 (PAON) - Body ground
    Ignition switch ON
    Below 1 V
    A21-17 (P-AB) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


15.CHECK WIRE HARNESS (POWER SOURCE)


    H101927E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    H7-3 (IG+) - Body ground
    Ignition switch ON
    10 to 14 V



NG
REPAIR OR REPLACE POWER SOURCE CIRCUIT
OK


16.CHECK HAZARD WARNING SIGNAL SWITCH ASSEMBLY


    H046184E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the hazard warning signal switch.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Using a service wire, connect H7-5 (SW-) and H7-7 (E) of hazard warning signal switch assembly connector.

  1. Using a service wire, connect H7-12 (AIR) and H7-7 (E) of hazard warning signal switch assembly connector.

  1. Turn the ignition switch to the ON position.

  1. Check the passenger airbag ON/OFF indicator operation.

    OK:
    Passenger airbag ON/OFF indicator comes on



NG
INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
OK


17.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    H100895E03
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the connector to the passenger seat belt warning light assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1660/43 is not output.

HINT:
DTCs other than B1660/43 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK