Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



TERMINALS OF ECU

C110610E02


Symbols (Terminal No.)
Terminal Description
GND (1)
Skid control ECU ground
+BM1 (2)
Power supply for motor
FR+ (3)
Front RH wheel speed sensor power supply
FL- (4)
Front LH wheel speed signal input
RR+ (5)
Rear RH wheel speed sensor power supply
RL- (6)
Rear LH wheel speed signal input
STP (7)
Stop light switch input
CANH (11)
CAN communication line H
SP1 (12)
Speed signal output for combination meter
D/G (13)
Diagnosis tester communication line
P/R (14)
Shift position indicator P signal input
INFR (15) (*1)
AUTO LSD indicator light output
STPO (16)
Stop light operated relay output
FR- (17)
Front RH wheel speed sensor input
FL+ (18)
Front LH wheel speed sensor power supply output
RR- (19)
Rear RH wheel speed sensor input
RL+ (20)
Rear LH wheel speed sensor power supply output
EXI4 (21) (*2)
Detection (L4) switch input
TS (24)
Sensor test terminal (Sensor check switch) input
CANL (25)
CAN communication line L
EXI3 (26)
Rear differential lock detection switch input
EXI (27)
4WD switch input
PKB (28)
Parking brake switch input
WA (29)
ABS warning light input
BZ (30)
Buzzer output
+BS (31)
Power supply for solenoid
GND2 (32)
Skid control ECU ground
HDCW (33) (*3)
DAC operation indicator light output
IND (34)
SLIP indicator light output
WT (35)
VSC OFF indicator light output
VSCW (36)
VSC TRAC warning light output
LBL (41)
Brake fluid level warning switch input
WFSE (42)
Write flash enable input
CSW (43) (*3)
AUTO LSD switch input
HDCS (44) (*3)
DAC operation switch input
STP2 (45)
Stop light switch input
IG1 (46)
IG1 power supply

C124763E01


Symbols (Terminal No.)
Terminal Description
IG2 (1)
IG2 Power supply
+BM2 (2)
Power supply for motor
BRL (3)
BRAKE warning light output
GND3 (4)
Skid control ECU ground
  1. (*1): with AUTO LSD
  2. (*2): 4WD
  3. (*3): with Downhill assist control

TERMINAL INSPECTION
Disconnect the connector and measure the voltage or resistance on the wire harness side.
(*1): A/T

HINT:
Voltage cannot be measured with the connector connected to the skid control ECU as the connector is water resistant.


C124764E01


Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
+BM1 (S1-2) - GND (S1-1, 32)
B - W-B
Power supply for motor
From battery
Always
10 to 14 V
IG1 (S1-46) - GND (S1-1, 32)
LG - W-B
IG1 power supply
IG switch OFF
Below 1 V
IG1 (S1-46) - GND (S1-1, 32)
LG- B-W
IG1 power supply
IG switch ON
10 to 14 V
STP (S1-7) - GND (S1-1, 32)
G-W - W-B
Stop light switch input
Stop light switch OFF (Brake pedal released)
Below 1.5 V
STP (S1-7) - GND (S1-1, 32)
G-W - W-B
Stop light switch input
Stop light switch ON (Brake pedal released)
8 to 14 V
P/R (S1-14) - GND (S1-1, 32) (*1)
BR-W - W-B
Shift position indicator P signal input
IG switch ON, shift P position
8 to 14 V
P/R (S1-14) - GND (S1-1, 32) (*1)
BR-W - W-B
Shift position indicator P signal input
IG switch ON, any shift position except P
Below 1 V
PKB (S1-28) - GND (S1-1, 32)
G-Y - W-B
Parking brake switch input
IG switch ON, parking brake switch ON
Below 1.5 V
PKB (S1-28) - GND (S1-1, 32)
G-Y - W-B
Parking brake switch input
IG switch ON, parking brake switch OFF
10 to 14 V
+BS (S1-31) - GND (S1-1, 32)
R - W-B
Power supply for solenoid
Form battery
Always
10 to 14 V
LBL (S1-41) - GND (S1-1, 32)
V-W - W-B
Brake fluid level warning switch input
Brake fluid level min. -5mm
Below 1 Ω
LBL (S1-41) - GND (S1-1, 32)
V-W - W-B
Brake fluid level warning switch input
Brake fluid level max.
1.9 to 2.1 Ω
STP2 (S1-45) - GND (S1-1, 32)
L - W-B
Stop light switch input
Stop light switch OFF (Brake pedal released)
Below 1.5 V
STP2 (S1-45) - GND (S1-1, 32)
L - W-B
Stop light switch input
Stop light switch ON (Brake pedal released)
8 to 14 V
IG2 (S2-1) - GND (S2-4)
O - W-B
IG2 power supply
IG switch OFF
Below 1 V
IG2 (S2-1) - GND (S2-4)
O - W-B
IG2 power supply
IG switch ON
10 to 14 V
+BM2 (S2-2) - GND (S2-4)
B - W-B
Power supply for motor
From battery
Always
10 to 14 V