VEHICLE STABILITY CONTROL SYSTEM > SYSTEM DESCRIPTION |
| SYSTEM DESCRIPTION |
ABS with EBD & BA & TRAC & VSC operation
The skid control ECU determines the wheel slipping conditions by receiving signals from each speed sensor, the yaw rate and deceleration sensor and the steering angle sensor. The ECU controls the engine output torque using electronic throttle control, and the wheel brake pressure using the brake actuator, according to these signals.
The SLIP indicator blinks and the skid control buzzer sounds to inform the driver that the VSC system is operating. The SLIP indicator also blinks when TRAC is operating, and the operation being performed is displayed.
| ACTIVE SAFETY |
ABS (Anti-lock Brake System)
The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.

EBD (Electronic Brake force Distribution)
The EBD control utilizes ABS, realizing proper brake force distribution between the front and rear wheels in accordance with the driving conditions.
In addition, when braking while cornering, it also controls the brake forces of the right and left wheels, helping to control the vehicle behavior.

BA (Brake Assist)
The primary purpose of the brake assist system is to provide an auxiliary brake force to assist drivers who cannot generate a large enough brake force during emergency braking, thus helping to maximize the vehicle's brake performance.

VSC (Vehicle Stability Control)
The VSC system helps prevent the vehicle from slipping sideways as a result of strong front wheel skid or strong rear wheel skid during cornering.

| DRIVING PERFORMANCE |
TRAC (Traction Control)
The TRAC system helps prevent the drive wheels from slipping if the driver presses down on the accelerator pedal excessively when starting off or accelerating on a slippery surface.

A-TRAC (Active Traction Control) (4WD)
During rugged off-road driving, this function controls the engine output and the brake fluid pressure that is applied to slipping wheels, and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve a LSD (Limited Slip Differential) effect. As a result, the vehicle's off-road drivability and ability to free itself from moguls have been increased.

AUTO-LSD (Auto Limited Slip Differential)
When the vehicle enters 2WD mode, the AUTO LSD operates with the AUTO LSD switch on and the accelerator pedal depressed.
The TRAC system restrains brake pressure and reduces differential move, thus transmitting the drive torque to the other drive wheel to ensure stability under the following conditions:

DAC (Downhill Assist Control) (4WD)
When the DAC switch is pressed with the transfer in low (L4) range and without the accelerator and brake pedals in operation, the DAC activates 4-wheel hydraulic pressure control, in order to maintain a constant low vehicle speed without causing the wheels to become locked. Thus, the vehicle can descend steep hills in a stable manner.

HAC (Hill-start Assist Control)
When the vehicle starts off on a steep hill, HAC detects the backward descent of the vehicle and effects 4-wheel hydraulic pressure control to reduce the speed of the vehicle.
For a Maximum of 5 seconds after the control starts, fluid pressure is gradually released and the control is complete.

| FUNCTION OF COMPONENTS |
| Components | Function |
| Speed sensor | Detects wheel speed of each wheel. |
| Hydraulic brake booster | Upon receiving brake control signal from skid control ECU, controls hydraulic circuit and sends hydraulic pressure to each wheel. Master cylinder solenoid (skid control ECU) removable. |
| Master cylinder solenoid Skid control ECU | Detects vehicle condition based on signals from sensors and sends brake control signal to hydraulic brake booster. |
| Motor relay | Supplies power source to pump motor. |
| Solenoid relay | Supplies power source to each solenoid. |
| ABS warning light | Illuminates to inform driver that skid control ECU has detected ABS system malfunction and terminated ABS system operation. |
| BRAKE warning light | Illuminates to inform driver that skid control ECU has detected BRAKE system malfunction. |
| VSC TRAC warning light | Illuminates to inform driver that skid control ECU has detected VSC system malfunction and terminated VSC system operation. |
| SLIP indicator light | Blinks to inform driver that TRAC or VSC in operation. |
| Yaw rate and deceleration sensor | Detects vehicle's yaw rate and deceleration and sends signal to skid control ECU. |
| Master cylinder pressure sensor | Built into hydraulic brake booster. Detects pressure inside master cylinder. |
| Steering angle sensor | Detects steering wheel's steering angle and amount of movement, then sends signal to skid control ECU. |
| ECM |
|