Home › TRANSMISSION · A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0756    Shift Solenoid "B" Performance (Shift Solenoid Valve S2)

for Preparation Click here


DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).

DTC No.
DTC Detection Conditions
Trouble Areas
P0756
  1. S2 stuck ON malfunction*1;
    The ECM determines that there is a malfunction when the following conditions are met (2-trip detection logic):
    1. When the ECM directs the gearshift to switch to 1st gear, the actual gear is shifted to 2nd.
    2. When the ECM directs the gearshift to switch to 5th gear, the engine overruns (clutch slips)
  1. Shift solenoid valve S2 remains open
  2. Shift solenoid valve SLT remains open or closed
  3. Valve body is blocked
  4. Automatic transmission (clutch, brake or gear, etc.)
  1. S2 stuck OFF malfunction*2:
    The ECM determines that there is a malfunction when the following conditions are met (2-trip detection logic):
    1. When the ECM directs the gearshift to switch to 1st gear, the actual gear is also shifted to 1st.
    2. When the ECM directs the gearshift to switch to 2nd gear, the actual gear is shifted to 1st.
    3. When the ECM directs the gearshift to switch to 5th gear, the actual gear is also shifted to 5th.
  1. Shift solenoid valve S2 remains closed
  2. Shift solenoid valve SLT remains open or closed
  3. Valve body is blocked
  4. Automatic transmission (clutch, brake or gear, etc.)

HINT:
Gear positions in the event of a solenoid valve mechanical problem:

Gearshift controlled by ECM
1st
2nd
3rd
4th
5th
*1: Actual gear position under S2 stuck ON malfunction
2nd
2nd
3rd
3rd
N*
*2: Actual gear position under S2 stuck OFF malfunction
2nd
1st
4th
4th
5th
N*: Neutral


MONITOR DESCRIPTION

This DTC indicates "stuck ON malfunction" or "stuck OFF malfunction" of the shift solenoid valve S2. The ECM controls the gearshifts by turning the shift solenoid valves "ON/OFF". When the gear position directed by the ECM and the actual gear position do not match, the ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0756:
Shift solenoid valve S2/OFF malfunction
Shift solenoid valve S2/ON malfunction
Required sensors/Components (Main)
Shift solenoid valve S2
Required sensors/Components (Related)
Vehicle speed sensor, Throttle position sensor, Speed sensor (NT), Speed sensor (SP2)
Frequency of operation
Continuous
Duration
OFF malfunctions (A), (B) and (C):
0.4 seconds
OFF malfunction (D):
Immediate
ON malfunctions (A) and (B):
0.4 seconds
ON malfunction (C):
3 seconds
ON malfunction (D):
0.5 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS

The following conditions are common to all OFF malfunctions (A), (B), (C), (D) and ON malfunctions (A), (B), (C), (D).

The monitor will run whenever the following DTCs are not present.
P0115 - P0118: ECT sensor
P0125: Insufficient ECT for Closed Loop
P0500: VSS
P0748 - P799: Trans solenoid (range)
Turbine speed sensor (NT) circuit
Functioning normally
Output speed sensor (SP2) circuit
Functioning normally
Shift solenoid "A" (S1) circuit
Functioning normally
Shift solenoid "B" (S2) circuit
Functioning normally
Shift solenoid "E" (SR) circuit
Functioning normally
Pressure control solenoid "A" (SL1) circuit
Functioning normally
Pressure control solenoid "B" (SL2) circuit
Functioning normally
ECT (Engine coolant temperature) sensor circuit
Functioning normally
Knock sensor circuit
Functioning normally
ETCS (Electronic throttle control system)
System not down
Transmission shift position
"D"
ECT
40°C (104°F) or more
Spark advance from max. retard timing by knock sensor control
0° CA or more
Engine
Starting

OFF malfunction (A) 
ECM selected gear
1st
Vehicle speed
1.2 to 24.9 mph (2 to 40 km/h)
Throttle valve opening angle
6.5 % or more at engine speed of 2,000 rpm
(Conditions vary with engine speed)

OFF malfunction (B) 
ECM selected gear
2nd
Vehicle speed
1.2 mph (2 km/h) or more
Output speed
2nd → 1st down shift point or more
Throttle valve opening angle
6.5 % or more at engine speed of 2,000 rpm
(Conditions vary with engine speed)

OFF malfunction (C) 
Current ECM selected gear
5th
Last ECM selected gear
4th
Continuous time of ECM selecting 4th gear
2 seconds or more
Actual gear when ECM selected 4th gear
4th

OFF malfunction (D) 
Current ECM selected gear
5th
Last ECM selected gear
4th

ON malfunction (A) 
ECM selected gear
1st
Vehicle speed
1.2 to 24.9 mph (2 to 40 km/h)
Throttle valve opening angle
6.5 % or more at engine speed of 2,000 rpm
(Conditions vary with engine speed)

ON malfunction (B) 
ECM selected gear
4th
Vehicle speed
1.2 mph (2 km/h) or more
Throttle valve opening angle
6.5 % or more at engine speed of 2,000 rpm
(Conditions vary with engine speed)

ON malfunction (C) 
Current ECM selected gear
5th
Last ECM selected gear
4th
Vehicle speed
(During transition from 4th to 5th gear)
Less than 62.2 mph (100 km/h)

ON malfunction (D) 
ECM selected gear
5th
Engine speed - Turbine speed (NE - NT)
(After transition from 4th to 5th gear)
150 rpm or less
Vehicle speed
(After transition from 4th to 5th gear)
Less than 62.2 mph (100 km/h)

TYPICAL MALFUNCTION THRESHOLDS

[OFF malfunction]
All of the following conditions are met: OFF malfunctions (A), (B), (C) and (D)
2 detections are necessary in 1 driving cycle.
1st detection; temporary flag ON
2nd detection; pending fault code ON

OFF malfunction (A) 
Turbine speed/Output speed
3.30 to 7.50
(Actual gear is 1st)

OFF malfunction (B) 
Turbine speed/Output speed
3.30 to 7.50
(Actual gear is 1st)

OFF malfunction (C) 
Turbine speed/Output speed
0.65 to 0.79
(Actual gear is 5th)

OFF malfunction (D) 
Output record from ECM for 4th → 5th upshifting
Recorded
[ON malfunction]
ON malfunction (A) or (B) and ON malfunction (C) or (D) are met:

ON malfunction (A) 
Turbine speed/Output speed
1.91 to 2.35
(Actual gear is 2nd)

ON malfunction (B) 
Turbine speed/Output speed
1.28 to 1.53
(Actual gear is 3rd)

ON malfunction (C) 
Turbine speed - Output speed x 4th gear ratio
1,000 rpm or more

ON malfunction (D) 
Turbine speed - Output speed x 5th gear ratio
1,000 rpm or more

INSPECTION PROCEDURE

HINT:
Performing the ACTIVE TEST using the intelligent tester allows components, such as the relay, VSV, and actuator, to be operated without removing any parts. Performing the ACTIVE TEST as a first step of troubleshooting is one method of shortening labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.
  4. Turn the ignition switch to the ON position.
  5. Push the "ON" button of the tester.
  6. Clear the DTC.
  7. Select the items "DIAGNOSIS/ ENHANCED OBD II/ ACTIVE TEST/ SHIFT".
  8. According to the display on the tester, perform the "ACTIVE TEST".

HINT:
While driving, the shift position can be changed with the intelligent tester.
Comparing the shift position directed by the ACTIVE TEST with the actual shift position enables the problem to be confirmed (Click here).

Item
Test Details
Diagnostic Note
SHIFT
[Test Details]
Operate the shift solenoid valve and set each shift position manually.
[Vehicle Condition]
Vehicle Speed: Less than 30 mph (50 km/h)
[Others]
  1. Press → button: Shift up
  2. Press ← button: Shift down
Possible to check the operation of the shift solenoid valves.
HINT:
Shifting to the 5th gear is possible only when the vehicle is stationary with the engine idling.

HINT:
  1. This test can be conducted when the vehicle speed is 30 mph (50 km/h) or less.
  2. The 4th to 5th up-shifting must be performed with the accelerator pedal released.
  3. The 5th to 4th down-shifting must be performed with the accelerator pedal released.
  4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
  5. The shift position directed by the ECM is shown in the DATA LIST/ SHIFT display on the intelligent tester.
  6. The shift solenoid valve S2 is turned on/off normally when the shift lever is in the D position:

    Gearshift controlled by ECM
    1st
    2nd
    3rd
    4th
    5th
    Shift solenoid valve S2
    OFF
    ON
    ON
    OFF
    OFF

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0756)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and push the intelligent tester main switch ON.

  1. Select the items "DIAGNOSIS/ ENHANCED OBD II/ DTC INFO/ CURRENT CODES".

  1. Read the DTCs using the intelligent tester.

    Result: 
    Display (DTC Output)
    Proceed to
    Only "P0756" is output
    A
    "P0756" and other DTCs
    B

    HINT:
    If any codes besides "P0756" are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (LINE PRESS UP)
G020657E01

NOTICE:
  1. Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F).
  2. Be careful to prevent SST's hose from interfering with the exhaust pipe.
  3. Perform the test with the A/C OFF.

HINT:
Performing the intelligent tester's ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time.
The DATA LIST can be displayed during the ACTIVE TEST.

  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the intelligent tester ON.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST.

  1. Follow the instructions on the tester and perform the ACTIVE TEST.

  1. Measure the line pressure with SST.

    Item
    Test Details
    Diagnostic Note
    LINE PRESS UP*
    [Test Details]
    Operate shift solenoid SLT and raise line pressure.
    [Vehicle Condition]
    1. Vehicle stopped
    2. IDL: ON

    HINT:
    OFF: Line pressure up (when Active Test of "LINE PRESS UP" is performed, ECM commands SLT solenoid to turn OFF)
    ON: No action (normal operation)

    -
    *: "LINE PRESS UP" in the ACTIVE TEST is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the HYDRAULIC TEST (Click here) as well. Please note that the pressure values in the ACTIVE TEST and HYDRAULIC TEST are different.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


3.INSPECT SHIFT SOLENOID VALVE S2


    A110987E04
  1. Remove the shift solenoid valve S2.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    Solenoid Connector (S2) - Solenoid Body (S2)
    11 to 15 Ωat 20°C (68°F)

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes an operating noise.



NG
REPLACE SHIFT SOLENOID VALVE S2
OK


4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (See chapter 2 in the problem symptoms table)

OK:
There are no foreign objects on any valves and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY