Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0705    Transmission Range Sensor Circuit Malfunction (PRNDL Input)

for Preparation Click here


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.

DTC No.
DTC Detection Conditions
Trouble Areas
P0705
When any one of following conditions (A) to (C) is met (2-trip detection logic):
(A) Any 2 or more signals of the following are ON simultaneously
  1. NSW input signal is ON.
  2. R input signal is ON.
  3. D input signal is ON.
  4. 3 input signal is ON.
  5. 2 input signal is ON.
(B) All switches are OFF simultaneously for P (NSW), R, N (NSW), D, 3 and 2 positions
(C) When NSW or R input signal is ON, 4 or L input signal is ON
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. ECM

MONITOR DESCRIPTION

The DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the vehicle is in the P or N shift position.
When the park/neutral position switch sends more than one signal at a time from switch positions P, R, N, D, 3 or 2, the ECM interprets this as a fault in the switch. The ECM will turn on the MIL and store the DTC.

MONITOR STRATEGY


Related DTCs
P0705: Park/neutral position switch/Verify switch input
Required sensors/Components
Park/neutral position switch
Frequency of operation
Continuous
Duration
Conditions (A) and (C):
2 seconds
Condition (B):
60 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present.
None
Ignition switch
ON
Battery voltage
10.5 V or more

TYPICAL MALFUNCTION THRESHOLDS

One of the following conditions is met: Condition (A), (B) or (C)

Condition (A) 
Number of the following signals input at the same time
2 or more
Park/neutral position switch
ON
R switch
ON
D switch
ON
3 switch
ON
2 switch
ON

All of following conditions are met
Condition (B) 
Park/neutral position switch
OFF
R switch
OFF
D switch
OFF
3 switch
OFF
2 switch
OFF

Both (i) and (ii) are met(i) One of following conditions is met
Condition (C) 
Park/neutral position switch
ON
R switch
ON
(ii) One of following conditions is met

4 switch
ON
L switch
ON

COMPONENT OPERATING RANGE


Park/neutral position switch
The park/neutral position switch sends only one signal to the ECM

WIRING DIAGRAM


C124515E02


INSPECTION PROCEDURE

HINT:
According to the DATA LIST displayed on the intelligent tester, you can read the values of components, such as the switches, sensors and actuators, without removing any parts. Reading the DATA LIST as a first step of troubleshooting is one method of shortening labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are for reference only. Do not depend solely on these reference values when judging whether a part is faulty or not.

  1. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.
  2. Turn the ignition switch to the ON position.
  3. Push the "ON" button of the tester.
  4. Select the items "DIAGNOSIS/ ENHANCED OBD II/ DATA LIST/ A/T".
  5. According to the display on the tester, read the "DATA LIST".

    Item
    Measurement Item/
    Display (Range)
    Normal Condition
    Diagnostic Note
    PNP SW [NSW]
    PNP Switch Status/
    ON or OFF
    Shift lever position is;
    P or N: ON
    Except P or N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    REVERSE
    PNP Switch Status/
    ON or OFF
    Shift lever position is;
    R: ON
    Except R: OFF
    DRIVE
    PNP Switch Status/
    ON or OFF
    Shift lever position is;
    D and 4: ON
    Except D and 4: OFF
    4th/DRIVE
    PNP Switch Status/
    ON or OFF
    Shift lever position is;
    4: ON
    Except 4: OFF
    3RD
    PNP Switch Status/
    ON or OFF
    Shift lever position is;
    3: ON
    Except 3: OFF
    2ND
    PNP Switch Status/
    ON or OFF
    Shift lever position is;
    2 and L: ON
    Except 2 and L: OFF
    LOW
    PNP Switch Status/
    ON or OFF
    Shift lever position is;
    L: ON
    Except L: OFF
1.INSPECT PARK / NEUTRAL POSITION SWITCH ASSEMBLY


    G026080E19
  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance when the shift lever is moved to each position.

Standard resistance:
Shift Position
Tester Connection
Specified Condition
P
2 - 6 and 4 - 5
Below 1 Ω
Except P
2 - 6 and 4 - 5
10 kΩ or higher
R
1 - 2
Below 1 Ω
Except R
1 - 2
10 kΩ or higher
N
2 - 9 and 4 - 5
Below 1 Ω
Except N
2 - 9 and 4 - 5
10 kΩ or higher
D, 4
2 - 7
Below 1 Ω
Except D, 4
2 - 7
10 kΩ or higher
3
2 - 3
Below 1 Ω
Except 3
2 - 3
10 kΩ or higher
2, L
2 - 8
Below 1 Ω
Except 2, L
2 - 8
10 kΩ or higher



NG
REPLACE PARK / NEUTRAL POSITION SWITCH ASSEMBLY
OK


2.INSPECT SHIFT LOCK CONTROL ECU SUB-ASSEMBLY


    D029380E08
  1. Connect the park/neutral position switch connector.

  1. Disconnect the shift lock control ECU connector.

  1. Measure the resistance when the shift lever is moved to each position.

Standard resistance:
Shift Position
Tester Connection
Specified Condition
D
9 (NSSD) - 2 (ATD)
Below 1 Ω
4
9 (NSSD) - 2 (ATD)
10 kΩ or higher
D
9 (NSSD) - 3 (AT4)
10 kΩ or higher
4
9 (NSSD) - 3 (AT4)
Below 1 Ω
2
10 (NSSL) - 5 (AT2)
Below 1 Ω
L
10 (NSSL) - 5 (AT2)
10 kΩ or higher
2
10 (NSSL) - 4 (ATL)
10 kΩ or higher
L
10 (NSSL) - 4 (ATL)
Below 1 Ω



NG
REPLACE SHIFT LOCK CONTROL ECU SUB-ASSEMBLY
OK


3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)


    G100772E02
  1. Connect the shift lock control ECU connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage when the shift lever is moved to each position.

    Standard voltage:
    Shift Position
    Tester Connection
    Specified Condition
    P and N
    E5-8 (NSW) - E6-1 (E1)
    Below 2 V
    Except P and N
    E5-8 (NSW) - E6-1 (E1)
    10 to 14 V
    R
    E7-11 (R) - E6-1 (E1)
    10 to 14 V*
    Except R
    E7-11 (R) - E6-1 (E1)
    Below 1 V
    D and 4
    E7-21 (D) - E6-1 (E1)
    10 to 14 V
    Except D and 4
    E7-21 (D) - E6-1 (E1)
    Below 1 V
    4
    E7-20 (4) - E6-1 (E1)
    10 to 14 V
    Except 4
    E7-20 (4) - E6-1 (E1)
    Below 1 V
    3
    E7-19 (3) - E6-1 (E1)
    10 to 14 V
    Except 3
    E7-19 (3) - E6-1 (E1)
    Below 1 V
    2 and L
    E7-10 (2) - E6-1 (E1)
    10 to 14 V
    Except 2 and L
    E7-10 (2) - E6-1 (E1)
    Below 1 V
    L
    E7-9 (L) - E6-1 (E1)
    10 to 14 V
    Except L
    E7-9 (L) - E6-1 (E1)
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to illumination of the back up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM