DTC P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P2757 | Lock-up does not occur when driving in the lock-up range (normal driving at 50 mph [80 km/h]), or lock-up remains ON in the lock-up OFF range. (2-trip detection logic) |
|
| Related DTCs | P2757: Shift solenoid valve SLU/OFF malfunction Shift solenoid valve SLU/ON malfunction |
| Required sensors/Components (Main) | Shift solenoid valve SLU |
| Required sensors/Components (Related) | Valve body, Vehicle speed sensor, Throttle position sensor, Speed sensor (NT), Speed sensor (SP2) |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A): 2 seconds OFF malfunction (B): 0.4 seconds ON malfunction: 1.8 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present. | None |
| Turbine speed sensor (NT) circuit | Functioning normally |
| Output speed sensor (SP2) circuit | Functioning normally |
| Shift solenoid "A" (S1) circuit | Functioning normally |
| Shift solenoid "B" (S2) circuit | Functioning normally |
| Shift solenoid "E" (SR) circuit | Functioning normally |
| Torque converter clutch pressure control solenoid circuit | Functioning normally |
| Knock sensor circuit | Functioning normally |
| ETCS (Electronic throttle control system) | System not down |
| Transmission shift position | "D" |
| ECT | 40°C (104°F) or more |
| Spark advance from max. retard timing by knock sensor control | 0° CA or more |
| Engine | Starting |
| ECM selected gear | 4th or 5th |
| Vehicle speed | 15.5 mph (25 km/h) or more |
| Shift solenoid "A" (S1) circuit | Functioning normally |
| Shift solenoid "B" (S2) circuit | Functioning normally |
| Pressure control solenoid "B" (SL2) circuit | Functioning normally |
| 1-2 shift valve | Functioning normally |
| Transfer neutral position switch | OFF |
| Transfer range | "High" *1
|
| Vehicle speed sensor "A" circuit | Functioning normally |
| Output speed sensor circuit | Functioning normally |
| Transfer output speed | 143 rpm or more |
| Transfer input speed/Transfer output speed | 0.9 to 1.1 |
| ECM lock-up request | ON (SLU pressure: 513 kPa or more) |
| Vehicle speed | Less than 62.2 mph (100 km/h) |
| ECM selected gear | 2nd |
| Vehicle speed | 1.2 mph (2 km/h) or more |
| Output speed | 2nd → 1st down shift point or more |
| Throttle valve opening angle | 6.5 % or more at engine speed of 2,000 rpm (Conditions vary with engine speed) |
| ECM lock-up request | OFF (SLU pressure: less than 4 kPa) |
| Throttle valve opening angle | 7 % or more |
| Vehicle speed | Less than 37.3 mph (60 km/h) |
| Engine speed - Turbine speed | 70 rpm or more |
| Turbine speed/Output speed | Not 3.3 to 7.50 |
| Difference between engine speed and turbine speed | Less than 35 rpm |
| Item | Test Details | Diagnostic Note |
| LOCK UP | [Test Details] Control the shift solenoid SLU to set the automatic transmission to the lock-up condition. [Vehicle Condition] Vehicle Speed: 36 mph (60 km/h) or more | Possible to check the SLU operation. |

| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2757) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and push the intelligent tester main switch ON.
Select the items "DIAGNOSIS/ ENHANCED OBD II/ DTC INFO/ CURRENT CODES".
Read the DTCs using the intelligent tester.
| Display (DTC Output) | Proceed to |
| Only "P2757" is output | A |
| P2757" and other DTCs | B |
|
| ||||
| A | |
| 2.INSPECT SHIFT SOLENOID VALVE SLU |
![]() |
Remove the shift solenoid valve SLU.
Measure the resistance.
| Tester Connection | Specified Condition |
| 1 - 2 | 5.0 to 5.6 Ω at 20°C (68°F) |
Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (See chapter 2 in the problem symptoms table) |
|
| ||||
| OK | |
| 4.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
Inspect the torque converter clutch assembly (Click here).
|
| ||||
| OK | ||
| ||