DTC P0781 1-2 Shift (1-2 Shift Valve) |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0781 | 1-2 shift valve malfunction: The ECM determines that there is a malfunction when the following conditions (a) and (b), or (a) and (c) are met (2-trip detection logic):
|
|
| Gearshift controlled by ECM | 1st | 2nd | 3rd | 4th | 5th |
| Actual gear position under malfunction | 1st | 1st | 3rd | 3rd | N* |
| Related DTCs | P0781: Valve body/Rationality check |
| Required sensors/Components (Main) | Valve body |
| Required sensors/Components (Related) | Automatic transmission assembly, Speed sensor (NT), Speed sensor (SP2), Vehicle speed sensor, Throttle position sensor |
| Frequency of operation | Continuous |
| Duration | Conditions (A) and (B) 0.4 seconds Condition (C) 3 seconds Condition (D) 0.5 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present. | P0115 - P0118: ECT sensor P0125: Insufficient ECT for Closed Loop P0500: VSS P0748 - P0799: Trans Solenoid (range) |
| Turbine speed sensor (NT) circuit | Functioning normally |
| Output speed sensor (SP2) circuit | Functioning normally |
| Shift solenoid "A" (S1) circuit | Functioning normally |
| Shift solenoid "B" (S2) circuit | Functioning normally |
| Shift solenoid "E" (SR) circuit | Functioning normally |
| Pressure control solenoid "A" (SL1) circuit | Functioning normally |
| Pressure control solenoid "B" (SL2) circuit | Functioning normally |
| ECT (Engine coolant temperature) sensor circuit | Functioning normally |
| Knock sensor circuit | Functioning normally |
| ETCS (Electronic throttle control system) | System not down |
| Transmission shift position | "D" |
| ECT | 40°C (104°F) or more |
| Spark advance from max. retard timing by knock sensor control | 0°CA or more |
| Engine | Starting |
| ECM selected gear | 2nd |
| Vehicle speed | 1.2 mph (2 km/h) or more |
| Output speed | 2nd → 1st down shift point or more |
| Throttle valve opening angle | 6.5 % or more at engine speed of 2,000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 4th |
| Vehicle speed | 1.2 mph (2 km/h) or more |
| Throttle valve opening angle | 6.5 % or more at engine speed of 2,000 rpm (Conditions vary with engine speed) |
| Current ECM selected gear | 5th |
| Last ECM selected gear | 4th |
| Vehicle speed (During transition from 4th to 5th gear) | Less than 62.2 mph (100 km/h) |
| ECM selected gear | 5th |
| Engine speed - Turbine speed (NE - NT) After transition from 4th to 5th gear) | 150 rpm or less |
| Vehicle speed After transition from 4th to 5th gear) | Less than 62.2 mph (100 km/h) |
| Turbine speed/Output speed | 3.30 to 7.50 (Actual gear is 1st) |
| Turbine speed/Output speed | 1.28 to 1.53 (Actual gear is 3rd) |
| Turbine speed - Output speed x 4th gear ratio | 1,000 rpm or more |
| Turbine speed - Output speed x 5th gear ratio | 1,000 rpm or more |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0781) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and push the main switch ON.
Select the items "DIAGNOSIS/ ENHANCED OBD II/ DTC INFO/ CURRENT CODES".
Read the DTCs using the intelligent tester.
| Display (DTC Output) | Proceed to |
| Only "P0781" is output | A |
| "P0781" and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT) |
| Item | Test Details | Diagnostic Note |
| SHIFT | [Test Details] Operate the shift solenoid valve and set each shift position manually. [Vehicle Condition] Vehicle Speed: Less than 30 mph (50 km/h) [Others]
| Possible to check the operation of the shift solenoid valves. HINT: Shifting to the 5th gear is possible only when the vehicle is stationary with the engine idling. |
| Gearshift operated by tester | 1st | 2nd | 3rd | 4th | 5th |
| Actual gear position under malfunction | 1st | 1st | 3rd | 3rd | N* |
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (LINE PRESS UP) |
![]() |
Remove the test plug on the transmission case center right side and connect SST.
Connect the intelligent tester to the DLC3.
Start the engine and warm it up.
Measure the line pressure with SST.
Turn the intelligent tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST.
Follow the instructions on the tester and perform the ACTIVE TEST.
Measure the line pressure with SST.
| Item | Test Details | Diagnostic Note |
| LINE PRESS UP* | [Test Details] Operate shift solenoid SLT and raise line pressure. [Vehicle Condition]
| - |
|
| ||||
| OK | |
| 4.CLEAR DTC AND PERFORM RUNNING TEST |
Clear the DTC, and check for the DTC again after conducting the "MONITOR DRIVE PATTERN FOR ECT TEST" (Click here).
|
| ||||
| OK | ||
| ||