Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2772    Transfer "L4" Switch Circuit

for Preparation Click here


DESCRIPTION

The ECM detects the signal from the transfer L4 position switch.
This DTC indicates that the transfer L4 position switch remains ON.

DTC No.
DTC Detection Conditions
Trouble Areas
P2772
  1. Transfer L4 position switch remains ON while vehicle running under following conditions for 1.8 seconds or more (1-trip detection logic)
    1. Output shaft speed: between 1,000 rpm and 3,000 rpm
    2. Transfer shift position: H
  1. Short in transfer L4 position switch circuit
  2. Transfer L4 position switch
  3. ECM

MONITOR DESCRIPTION

The ECM monitors the transfer-case L4 position switch to determine whether the transfer-case L4 gear is engaged. If the transfer-case L4 gears remain engaged under the following conditions, the ECM determines that there is a malfunction of the L4 position switch:
  1. L4 switch indicates that the L4 transfer-case gears are engaged.
  2. Transfer-case shifter is in the "H" position.
  3. Transfer-case output shaft rpm is between 1,000 and 3,000 rpm.
  4. The specified time period has elapsed.
If all of the above conditions are met, the ECM determines that there is a malfunction of the L4 switch, illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P2772 : Transfer L4 position switch/ON malfunction
Required sensors/Components
Transfer L4 position switch
Frequency of operation
Continuous
Duration
ON malfunction (A)
1.8 seconds
ON malfunction (B)
0.5 seconds
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS

The following conditions are common to all ON malfunctions (A) and (B).

The monitor will run whenever the following DTCs are not present.
None
Output speed sensor (SP2) circuit
Functioning normally
Vehicle speed sensor "A" circuit
Functioning normally
Transmission neutral position switch
OFF

ON malfunction (A) 
Output speed (Transfer output speed)
1,000 to 3,000 rpm

ON malfunction (B) 
Output speed (Transfer output speed)
143 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met: ON malfunctions (A) and (B)

ON malfunction (A) 
L4 switch
ON

ON malfunction (B) 
Actual transfer gear ratio
Transfer input speed/Transfer output speed
0.9 to 1.1

WIRING DIAGRAM


C124521E01


INSPECTION PROCEDURE

1.INSPECT NO. 2 TRANSFER INDICATOR SWITCH (TRANSFER L4 POSITION SWITCH)


    C124524E01
  1. Remove the transfer L4 position switch.

  1. Measure the resistance when pushing the ball at the tip of the switch.

    Standard resistance:
    Switch Ball
    Tester Connection
    Specified Condition
    Push
    1 - 2
    Below 1 Ω
    Free
    1 - 2
    10 kΩ or higher



NG
REPLACE NO. 2 TRANSFER INDICATOR SWITCH (TRANSFER L4 POSITION SWITCH)
OK


2.CHECK HARNESS AND CONNECTOR (ECM - L4 POSITION SWITCH, L4 POSITION SWITCH - BODY GROUND)


    G035617E05
  1. Install the transfer L4 position switch.

  1. Disconnect the ECM connector.

  1. Measure the resistance when the transfer shift lever is in any position other than the L position.

    Standard resistance:
    Condition
    Tester Connection
    Specified Condition
    Transfer shift lever other than L position
    E6-13 (L4) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM