Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > Downhill Assist Control Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

When the Downhill Assist Control (DAC) switch is pushed on, the DAC function is available and the DAC indicator light illuminates.

HINT:
Even if the DAC switch is pressed, the DAC indicator light blinks and DAC does not activate under the following conditions:
  1. Transfer is in 2WD or H4 mode.
  2. ABS system is malfunctioning.
  3. Temperature of the hydraulic brake booster increases and DAC is temporarily canceled.


WIRING DIAGRAM


C124785E01


INSPECTION PROCEDURE

1.CHECK SKID CONTROL ECU CONNECTOR
  1. Check the ECU connecting condition.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR CORRECTLY
OK


2.INSPECT BATTERY
  1. Check the battery voltage.

    Standard:
    11 to 14 V



NG
INSPECT CHARGING SYSTEM
OK


3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)


    F049387E07
  1. Disconnect the skid control ECU connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Specified Condition
    S1-33 (HDCW) - C10-13
    Below 1 Ω
    S1-33 (HDCW) - Body ground
    10 kΩ or higher

  1. Reconnect the combination meter connector.

  1. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT COMBINATION METER ASSEMBLY
  1. Check the combination meter system (Click here).

    OK:
    Combination meter is normal.



NG
REPLACE COMBINATION METER ASSEMBLY
OK


5.INSPECT SKID CONTROL ECU (HDCS TERMINAL)


    C121700E23
  1. Disconnect the skid control ECU connector.

  1. Ground terminal HDCS of the skid control ECU.

    Standard:
    Tester Connection
    Condition
    Specified Condition
    S1-44 (HDCS) - Body ground
    DAC switch not pushed in
    10 kΩ or higher

  1. Reconnect the skid control ECU connector.



OK
REPLACE MASTER CYLINDER SOLENOID
NG


6.INSPECT DOWNHILL ASSIST CONTROL SWITCH


    I044044E02
  1. Remove the DAC switch.

  1. Disconnect the DAC switch connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Switch Condition
    Specified Condition
    D8-3 - D8-4
    Released
    10 kΩ or higher
    D8-3 - D8-4
    Pushed in
    Below 1 Ω

  1. Reconnect the DAC switch connector.

  1. Reinstall the DAC switch connector.



NG
REPLACE DOWNHILL ASSIST CONTROL SWITCH
OK


7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - DAC SWITCH)


    F052063E02
  1. Disconnect the skid control ECU connector.

  1. Disconnect the DAC Switch connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Specified Condition
    S1-44 (HDCS) - D8-3
    Below 1 Ω
    S1-44 (HDCS) - Body ground
    10 kΩ or higher
    D8-4 - Body ground
    Below 1 Ω

  1. Reconnect the DAC switch connector.

  1. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID