Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > AUTO LSD Indicator Light does not Come ON

for Preparation Click here


DESCRIPTION

Click here.

WIRING DIAGRAM

Click here.

INSPECTION PROCEDURE

1.CHECK AUTO LSD INDICATOR LIGHT


    C121700E27
  1. Disconnect the skid control ECU connector.

  1. Turn the ignition switch to the ON position.

  1. Ground terminal INFR of the skid control ECU.

  1. Check the AUTO LSD indicator light.

    OK:
    INFR - GND Condition
    Illumination Condition
    Connecting
    OFF
    Disconnecting
    ON

  1. Turn the ignition switch to OFF.

  1. Reconnect the skid control ECU connector.



OK
REPLACE MASTER CYLINDER SOLENOID
NG


2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)


    F049577E01
  1. Disconnect the skid control ECU connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Specified Condition
    S1-15 (INFR) - C9?35
    Below 1 Ω
    S1-15 (INFR) - Body ground
    10 kΩ or higher

  1. Reconnect the combination meter connector.

  1. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT COMBINATION METER ASSEMBLY
  1. Check the combination meter system (Click here).

    OK:
    Combination meter is normal.



NG
REPLACE COMBINATION METER ASSEMBLY
OK


4.INSPECT SKID CONTROL ECU (CSW TERMINAL)


    C121700E26
  1. Disconnect the skid control ECU connector.

  1. Ground terminal CSW of the skid control ECU.

    Standard:
    Tester connection
    Condition
    Specified Condition
    S1-43 (CSW) - Body ground
    Auto LSd switch not pushed in
    10 kΩ or higher

  1. Reconnect the skid control ECU connector.



OK
REPLACE MASTER CYLINDER SOLENOID
NG


5.INSPECT AUTO LSD SWITCH


    I044044E01
  1. Remove the AUTO LSD switch.

  1. Disconnect the AUTO LSD switch connector.

  1. Measure resistance.

    Standard:
    Tester Connection
    Switch Condition
    Specified Condition
    T9-3 - T9-4
    Released
    10 kΩ or higher
    T9-3 - T9-4
    Pushed in
    Below 1 Ω

  1. Reconnect the AUTO LSD switch connector.

  1. Reinstall the AUTO LSD switch.



NG
REPLACE AUTO LSD SWITCH
OK


6.CHECK HARNESS AND CONNECTOR (AUTO LSD SWITCH CIRCUIT)


    C124802E01
  1. Disconnect the skid control ECU connector and the AUTO LSD switch connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Specified Condition
    S1-43 (CSW) - T9-3
    Below 1 Ω
    S1-43 (CSW) - Body ground
    10 kΩ or higher
    T9-4 - Body ground
    Below 1 Ω

  1. Reconnect the skid control ECU connector and the AUTO LSD switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID 

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)


    F049577E01
  1. Disconnect the skid control ECU connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Specified Condition
    S1-15 (INFR) - C9-35
    Below 1 Ω
    S1-15 (INFR) - Body ground
    10 kΩ or higher

  1. Reconnect the combination meter connector.

  1. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT COMBINATION METER ASSEMBLY
  1. Check the combination meter system (Click here).

    OK:
    Combination meter is normal.



NG
REPLACE COMBINATION METER ASSEMBLY
OK

CHECK FOR INTERMITTENT PROBLEMS