Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Driver Side Power Window does not Operate with Power Window Master Switch

for Preparation Click here


DESCRIPTION

If the manual UP/DOWN function does not operate, the power window regulator master switch assembly, the power window regulator motor assembly or the wire harness may be malfunctioning.

WIRING DIAGRAM


B124993E02


INSPECTION PROCEDURE

1.INSPECT FUSE (D FR P/W)
  1. Remove the D FR P/W fuse from the driver side J/B.

  1. Check the resistance.

    Standard Resistance:
    Below 1 Ω

  1. Reinstall the D FR P/W fuse.



NG
REPLACE FUSE
OK


2.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
  1. Turn the ignition switch to ON.



    B126370E02
  1. Measure the voltage.

    Standard Voltage (Double cab):
    Tester Connection
    Condition
    Specified Condition
    P9-7 (B) - Body ground
    Ignition switch ON
    10 to 14 V

    Standard Voltage (Access cab):
    Tester Connection
    Condition
    Specified Condition
    P9-9 (B) - Body ground
    Ignition switch ON
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVER SIDE J/B - REGULATOR MASTER SWITCH)
OK


3.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
  1. Disconnect the P9 power window regulator master switch connector.

  1. Using a service wire, connect the terminals according to the table below.

  1. Turn the ignition switch to ON.



    B126370E03
  1. Check the operation of the power window regulator motor assembly LH.

    OK (Double cab):
    Wire Connection
    Specified Condition
    P9-4 (DU) - P9-7 (B)
    P9-9 (DD) - Body ground
    Power window moves UP
    P9-4 (DU) - Body ground
    P9-7 (B) - P9-9 (DD)
    Power window moves DOWN

    OK (Access cab):
    Wire Connection
    Specified Condition
    P9-3 (DU) - P9-9 (B)
    P9-4 (DD) - Body ground
    Power window moves UP
    P9-3 (DU) - Body ground
    P9-9 (B) - P9-4 (DD))
    Power window moves DOWN

  1. Reconnect the power window regulator master switch connector.



OK
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
NG


4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (SWITCH OPERATION)
  1. Remove the power window regulator master switch.

  1. Disconnect the P9 power window regulator master switch connector.



    B126368E01
  1. Measure the resistance between the terminals of the connector when the switch is operated.

    Standard (Double cab):
    Tester Connection
    AUTO Switch
    Specified Condition
    P9-1 (E) - P9-9 (DD)
    P9-4 (DU) - P9-7 (B)
    UP
    Below 1 Ω
    P9-1 (E) - P9-4 (DU)
    P9-1 (E) - P9-9 (DD)
    OFF
    Below 1 Ω
    P9-1 (E) - P9-4 (DU)
    P9-7 (B) - P9-9 (DD)
    DOWN
    Below 1 Ω

    Standard (Access cab):
    Tester Connection
    AUTO Switch
    Specified Condition
    P9-1 (E) - P9-4 (DD)
    P9-3 (DU) - P9-9 (B)
    UP
    Below 1 Ω
    P9-1 (E) - P9-3 (DU)
    P9-1 (E) - P9-4 (DD)
    OFF
    Below 1 Ω
    P9-1 (E) - P9-3 (DU)
    P9-9 (B) - P9-4 (DD)
    DOWN
    Below 1 Ω

  1. Reconnect the power window regulator master switch connector.

  1. Reinstall the power window regulator master switch.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK


5.CHECK HARNESS AND CONNECTOR (REGULATOR MASTER SWITCH - REGULATOR MOTOR AND BODY GROUND)
  1. Disconnect the P9 power window regulator master switch connector.

  1. Disconnect the P10 power window regulator motor connector.



    B126367E01
  1. Measure the resistance.

    Standard (Double cab):
    Tester Connection
    Specified Condition
    P9-9 (DD) - P10-1 (D)
    Below 1 Ω
    P9-4 (DU) - P10-2 (U)
    Below 1 Ω
    P9-9 (DD) - Body ground
    10 kΩ or higher
    P9-4 (DU) - Body ground
    10 kΩ or higher

    Standard (Access cab):
    Tester Connection
    Specified Condition
    P9-4 (DD) - P10-1 (D)
    Below 1 Ω
    P9-3 (DU) - P10-2 (U)
    Below 1 Ω
    P9-4 (DD) - Body ground
    10 kΩ or higher
    P9-3 (DU) - Body ground
    10 kΩ or higher

  1. Reconnect the power window regulator master switch connector.

  1. Reconnect the power window regulator motor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
  1. Remove the power window regulator motor.

  1. Apply battery voltage to connector terminals 1 and 2.



    B051847E01
  1. Check that the motor smoothly rotates.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 2.

    OK:
    Terminal No.
    Specified Condition
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise

  1. Reinstall the power window regulator motor.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASTER SWITCH - REGULATOR SWITCH)