Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Rear Power Window RH does not Operate with Rear Power Window Switch RH

for Preparation Click here


DESCRIPTION

If the rear RH side manual UP/DOWN function does not operate, the power window regulator motor assembly, the power window regulator switch assembly or the wire harness may be malfunctioning.

WIRING DIAGRAM


B124985E04


INSPECTION PROCEDURE

1.CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (B VOLTAGE)


    B062901E06
  1. Disconnect the P16 power window regulator switch connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage.

    Standard:
    Tester Connection
    Condition
    Specified Condition
    P16-3 (B) - Body ground
    Ignition switch ON
    10 to 14 V

  1. Reconnect the power window regulator switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVER SIDE J/B - REGULATOR SWITCH)
OK


2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (SWITCH OPERATION)


    B087962E01
  1. Remove the power window regulator switch.

  1. Disconnect the P16 power window regulator switch connector.

  1. Measure the resistance between the terminals of the connector when the switch is operated.

    Standard:
    Tester Connection
    Regulator Switch
    Specified Condition
    P16-5 (D) - P16-4 (SD)
    P16-1 (U) - P16-3 (B)
    UP
    Below 1 Ω
    P16-5 (D) - P16-4 (SD)
    P16-1 (U) - P16-2 (SU)
    OFF
    Below 1 Ω
    P16-1 (D) - P16-3 (B)
    P16-1 (U) - P16-2 (SU)
    DOWN
    Below 1 Ω

  1. Reconnect the power window regulator switch connector.

  1. Reinstall the power window regulator switch.



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY
OK


3.CHECK HARNESS AND CONNECTOR (REGULATOR SWITCH - REGULATOR MOTOR AND BODY GROUND)


    B063164E04
  1. Disconnect the P16 power window regulator switch connector.

  1. Disconnect the P13 power window regulator motor connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Specified Condition
    P16-5 (D) - P13-1
    Below 1 Ω
    P16-1 (U) - P13-2
    Below 1 Ω
    P16-5 (D) - Body ground
    10 kΩ or higher
    P16-1 (U) - Body ground
    10 kΩ or higher

  1. Reconnect the power window regulator switch connector.

  1. Reconnect the power window regulator motor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH)


    B067305E06
  1. Remove the power window regulator motor.

  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the motor smoothly rotates.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 2.

    OK:
    Terminal No.
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates clockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates counterclockwise

  1. Reinstall the power window regulator motor.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REGULATOR MASTER SWITCH - REGULATOR SWITCH)