Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

If the passenger side manual UP/DOWN function does not operate, the power window regulator motor assembly, the power window regulator switch assembly or the wire harness may be malfunctioning.

WIRING DIAGRAM


B124985E02


INSPECTION PROCEDURE

1.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (B VOLTAGE)


    B062901E04
  1. Disconnect the P14 power window regulator switch connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage.

    Standard:
    Tester Connection
    Condition
    Specified Condition
    P14-4 (B) - Body ground
    Ignition switch ON
    10 to 14 V

  1. Reconnect the power window regulator switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVER SIDE J/B - REGULATOR SWITCH)
OK


2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (SWITCH OPERATION)


    B063163E08
  1. Remove the power window regulator switch.

  1. Disconnect the P14 power window regulator switch connector.

  1. Measure the resistance between the terminals of the connector when the switch is operated.

    Standard:
    Tester Connection
    Regulator Switch
    Specified Condition
    P14-1 (D) - P14-2 (SD)
    P14-3 (U) - P14-4 (B)
    UP
    Below 1 Ω
    P14-1 (D) - P14-2 (SD)
    P14-3 (U) - P14-5 (SU)
    OFF
    Below 1 Ω
    P14-1 (D) - P14-4 (B)
    P14-3 (U) - P14-5 (SU)
    DOWN
    Below 1 Ω

  1. Reconnect the power window regulator switch connector.

  1. Reinstall the power window regulator switch.



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY
OK


3.CHECK HARNESS AND CONNECTOR (REGULATOR SWITCH - REGULATOR MOTOR AND BODY GROUND)


    B063164E05
  1. Disconnect the P14 power window regulator switch connector.

  1. Disconnect the P11 power window regulator motor connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Specified Condition
    P14-1 (D) - P11-1
    Below 1 Ω
    P14-3 (U) - P11-2
    Below 1 Ω
    P14-1 (D) - Body ground
    10 kΩ or higher
    P14-3 (U) - Body ground
    10 kΩ or higher

  1. Reconnect the power window regulator switch connector.

  1. Reconnect the power window regulator motor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


    B067305E06
  1. Remove the power window regulator motor.

  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the motor smoothly rotates.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 2.

    OK:
    Terminal No.
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates clockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates counterclockwise

  1. Reinstall the power window regulator motor.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASTER SWITCH - REGULATOR SWITCH)