Home › BODY › EXTERIOR › WHEEL OPENING MOULDING

WHEEL OPENING MOULDING > INSTALLATION

for Preparation Click here



1. INSTALL QUARTER PANEL WHEEL OPENING MOULDING


    B087686E01
  1. for 4WD and Pre Runner:

    1. Install new No. 1 quarter panel moulding pad in the position shown in the illustration.



    2. B087687E01
    3. Install each clip in the position shown in the illustration.

      NOTICE:
      If you install the clips wrongly, the installation of the quarter panel wheel opening moulding would be improper.



    4. B087688E01
    5. Engage the 10 clips and install the quarter panel wheel opening moulding.



    6. B087684E01
    7. Tighten the 5 screws.



    B087654E01
  1. for X-Runner:

    1. Install new No. 1 quarter panel moulding pad in the position shown in the illustration.



    2. B087653E01
    3. Install the quarter panel wheel opening moulding with the 5 screws.



2. INSTALL BODY ROCKER PANEL MOULDING ASSEMBLY (for X-Runner)


    B087662E01
  1. Install new No. 2 body outside moulding pad in the position shown in the illustration.



    B087663E01
  1. Install each clip in the position shown in the illustration.

    NOTICE:
    If you install the clips wrongly, the installation of the body rocker panel moulding would be improper.



    B087664E01
  1. Engage the 3 claws and install the body rocker panel moulding.



    B087660E01
  1. Tighten the 3 screws.



3. INSTALL BACK DOOR OUTSIDE MOULDING SUB-ASSEMBLY (for X-Runner)


    B087667E01
  1. Install new No. 3 body outside moulding pad in the position shown in the illustration.



    B087668E01
  1. Install each clip in the position shown in the illustration.

    NOTICE:
    If you install the clips wrongly, the installation of the back door outside moulding would be improper.



    B087669E01
  1. Engage the 3 clips and install the back door outside moulding.



    B087665E01
  1. Tighten the 3 screws.



4. INSTALL REAR QUARTER PANEL MUDGUARD (for 4WD and Pre-Runner)


    B087509E01
  1. for 2WD:

    1. Install the rear quarter panel mudguard with the 3 screws.



    B087508E01
  1. for 4WD and Pre Runner:

    1. Install the rear quarter panel mudguard with the 3 screws.

    2. Install the 3 clips.



5. INSTALL FRONT FENDER WHEEL OPENING MOULDING


    B087681E01
  1. for 4WD and Pre Runner:

    1. Install new No. 1 front fender wheel opening extension pad in the position shown in the illustration.



    2. B087682E01
    3. Install each clip in the position shown in the illustration.

      NOTICE:
      If you install the clip wrongly, the installation of the front fender wheel opening moulding would be improper.



    4. B087683E01
    5. Engage the 9 clips and install the front fender wheel opening moulding.



    6. B087679E01
    7. Tighten the 4 screws.



    B087652E01
  1. for X-Runner:

    1. Install new No. 2 body outside moulding pad in the position shown in the illustration.



    2. B087651E01
    3. Install the front fender wheel opening moulding with the 5 screws.



6. INSTALL ROCKER PANEL MOULDING (for X-Runner)


    B087657E02
  1. Install new No. 1 body outside moulding pad in the position shown in the illustration.



    B087658E02
  1. Install each clip in the position shown in the illustration.

    NOTICE:
    If you install the clips wrongly, the installation of the rocker panel moulding would be improper.



    B087659E01
  1. Engage the 9 clips and install the rocker panel moulding.



    B087655E01
  1. Tighten the 4 screws.



7. INSTALL FRONT FENDER MUDGUARD (for 4WD and Pre-Runner)


    B087507E01
  1. Install the front fender mudguard with the 3 screws.

  1. Install the 3 clips.