TIRE PRESSURE WARNING RECEIVER > INSTALLATION |
| 1. INSTALL TIRE PRESSURE WARNING RECEIVER |
![]() |
Install the tire pressure warning receiver with the nut.
Connect the connector.
| 2. INSTALL ROOF HEADLINING ASSEMBLY (for Double Cab) |
| 3. INSTALL ROOF HEADLINING ASSEMBLY (for Regular Cab) |
| 4. INSTALL ROOF HEADLINING ASSEMBLY (for Access Cab) |
| 5. INSTALL COAT HOOK (for Double Cab) |
![]() |
Turn the coat hook 90° clockwise and install it.
| 6. INSTALL COAT HOOK (for Regular Cab) |
![]() |
Turn the coat hook 90° clockwise and install it.
| 7. INSTALL COAT HOOK (for Access Cab) |
![]() |
Turn the coat hook 90° clockwise and install it.
| 8. INSTALL VISOR HOLDER (for Double Cab) |
![]() |
Turn the visor holder 90° clockwise and install it.
| 9. INSTALL VISOR HOLDER (for Regular Cab) |
![]() |
Turn the visor holder 90° clockwise and install it.
| 10. INSTALL VISOR HOLDER (for Access Cab) |
![]() |
Turn the visor holder 90° clockwise and install it.
| 11. INSTALL VISOR ASSEMBLY LH (for Double Cab) |
![]() |
Install the visor into the visor holder.
Tighten the 2 screws.
| 12. INSTALL VISOR ASSEMBLY LH (for Regular Cab) |
![]() |
Install the visor into the visor holder.
Install the 2 screws.
| 13. INSTALL VISOR ASSEMBLY LH (for Access Cab) |
![]() |
Install the visor into the visor holder.
Tighten the 2 screws.
| 14. INSTALL VISOR ASSEMBLY RH (for Double Cab) |
| 15. INSTALL VISOR ASSEMBLY RH (for Regular Cab) |
| 16. INSTALL VISOR ASSEMBLY RH (for Access Cab) |
| 17. INSTALL ASSIST GRIP PLUG (for Double Cab) |
![]() |
Engage the claw and install the assist grip plug.
Tighten the screw.
![]() |
Engage the 2 claws and close the cover.
| 18. INSTALL ASSIST GRIP SUB-ASSEMBLY (for Double Cab) |
![]() |
Install the assist grip with the 2 screws.
![]() |
Engage the 2 claws and close the cover.
| 19. INSTALL ROOF CONSOLE BOX ASSEMBLY (for Double Cab) |
![]() |
Install the wire harness clamp.
![]() |
Connect the accessory meter connector and map lamp connector.
Engage the 2 clips and 3 claws and install the map lamp.
Tighten the screw.
| 20. INSTALL ROOF CONSOLE BOX ASSEMBLY (for Access Cab) |
![]() |
Install the wire harness clamp.
![]() |
Connect the accessory meter connector and map lamp connector.
Engage the 2 clips and 3 claws and install the map lamp.
Tighten the screw.
| 21. INSTALL ROOM LIGHT ASSEMBLY (for Double Cab) |
![]() |
Connect the room light connector.
Engage the 3 claws and install the room light.
![]() |
Engage the 2 claws and install the room light lens.
| 22. INSTALL ROOM LIGHT ASSEMBLY (for Regular Cab) |
![]() |
Connect the room light connector.
Engage the 3 claws and install the room light.
![]() |
Engage the 2 claws and install the room light lens.
| 23. INSTALL ROOM LIGHT ASSEMBLY (for Access Cab) |
![]() |
Connect the room light connector.
Engage the 3 claws and install the room light.
![]() |
Engage the 2 claws and install the room light lens.
| 24. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror) |
![]() |
Engage the 2 claws and install the inner rear view mirror cover.
![]() |
Slide and install the inner rear view mirror.
![]() |
Slide the inner rear view mirror cover.
Connect the EC mirror connector.
| 25. INSTALL QUARTER INSIDE TRIM BOARD LH (for Double Cab) |
![]() |
Engage the 2 clips and install the quarter inside trim board.
Tighten the 3 screws.
![]() |
Engage the claw and close the cover.
![]() |
Install the floor anchor of the rear seat belt outer with the bolt.
| 26. INSTALL QUARTER INSIDE TRIM BOARD LH (for Regular Cab) |
![]() |
Engage the 2 clips and install the quarter trim board.
Tighten the 3 screws.
![]() |
Engage the claw and close the cover.
![]() |
for LH Side and Separate Seat Type RH Side:
Install the floor anchor of the front seat outer belt with the bolt.
![]() |
for Bench Seat Type RH Side:
Install the wiring harness clamp.
Connect the belt tension sensor connector.
Install the floor anchor of the front seat outer belt with the bolt.
| 27. INSTALL QUARTER INSIDE TRIM BOARD LH (for Access Cab) |
![]() |
Engage the 3 clips and install the quarter inside trim board.
Tighten the screw.
![]() |
Engage the claw and close the cover.
| 28. INSTALL QUARTER INSIDE TRIM BOARD RH (for Double Cab) |
| 29. INSTALL QUARTER INSIDE TRIM BOARD RH (for Regular Cab) |
| 30. INSTALL QUARTER INSIDE TRIM BOARD RH (for Access Cab) |
| 31. INSTALL QUARTER TRIM LOWER PANEL LH (for Double Cab) |
![]() |
Engage the 2 claws and 2 clips, and install the quarter trim lower panel.
| 32. INSTALL QUARTER TRIM LOWER PANEL LH (for Regular Cab) |
![]() |
Engage the 2 claws and 3 clips, and install the quarter trim lower panel.
| 33. INSTALL QUARTER TRIM LOWER PANEL LH (for Access Cab) |
![]() |
Engage the claw and 2 clips, and install the quarter trim lower panel.
![]() |
Install the floor anchor of the rear seat belt outer with the bolt.
| 34. INSTALL QUARTER TRIM LOWER PANEL RH (for Double Cab) |
| 35. INSTALL QUARTER TRIM LOWER PANEL RH (for Regular Cab) |
| 36. INSTALL QUARTER TRIM LOWER PANEL RH (for Access Cab) |
| 37. INSTALL CENTER PILLAR UPPER GARNISH LH (for Double Cab) |
![]() |
Engage the clip and install the center pillar upper garnish.
Tighten the 2 screws.
| 38. INSTALL CENTER PILLAR UPPER GARNISH RH (for Double Cab) |
| 39. INSTALL CENTER PILLAR LOWER GARNISH LH (for Double Cab) |
![]() |
Engage the 2 claws and 2 clips, and install the center pillar lower garnish.
![]() |
Install the floor anchor of the front seat outer belt with the bolt.
| 40. INSTALL CENTER PILLAR LOWER GARNISH RH (for Double Cab) |
| 41. INSTALL LAP BELT OUTER ANCHOR COVER (for Double Cab) |
![]() |
Engage the 3 claws and install the lap belt outer anchor cover.
| 42. INSTALL FRONT PILLAR GARNISH LH (for Double Cab) |
![]() |
Install the 3 wire harness clamps (LH side only).
![]() |
Engage the claw and clip, and install the front pillar garnish.
Tighten the 2 screws.
![]() |
Engage the 2 claws and install the assist grip plug.
| 43. INSTALL FRONT PILLAR GARNISH LH (for Regular Cab) |
![]() |
for LH Side:
Install the 3 wire harness clamps.
![]() |
Engage the claw and clip, and install the front pillar garnish.
Tighten the 2 screws.
![]() |
Engage the 2 claws and install the assist grip plug.
| 44. INSTALL FRONT PILLAR GARNISH LH (for Access Cab) |
![]() |
for LH Side:
Install the 3 wire harness clamps.
![]() |
Engage the claw and clip, and install the front pillar garnish.
Tighten the 2 screws.
![]() |
Engage the 2 claws and install the assist grip plug.
| 45. INSTALL FRONT PILLAR GARNISH RH (for Double Cab) |
| 46. INSTALL FRONT PILLAR GARNISH RH (for Regular Cab) |
| 47. INSTALL FRONT PILLAR GARNISH RH (for Access Cab) |
| 48. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Double Cab) |
![]() |
Install the rear door opening trim weatherstrip.
| 49. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Double Cab) |
| 50. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Double Cab) |
![]() |
Install the front door opening trim weatherstrip.
| 51. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Regular Cab) |
![]() |
Install the front door opening trim weatherstrip.
| 52. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Access Cab) |
![]() |
Install the front door opening trim weatherstrip.
| 53. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Double Cab) |
| 54. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Regular Cab) |
| 55. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Access Cab) |
| 56. INSTALL ROOF SIDE INNER GARNISH LH (for Access Cab) |
![]() |
Engage the 2 claws and clip, and install the roof side inner garnish.
| 57. INSTALL ROOF SIDE INNER GARNISH RH (for Access Cab) |
| 58. INSTALL ROOF SIDE INNER GARNISH CAP LH (for Access Cab) |
![]() |
Engage the 4 claws and install the roof side inner garnish cap.
Using a "Torx" socket wrench T30, tighten the 2 screws.
| 59. INSTALL ROOF SIDE INNER GARNISH CAP RH (for Access Cab) |
| 60. INSTALL ROOF SIDE INNER GARNISH COVER LH (for Access Cab) |
![]() |
Engage the 2 claws and install the roof side inner garnish cover.
| 61. INSTALL ROOF SIDE INNER GARNISH COVER RH (for Access Cab) |
| 62. INSTALL COWL SIDE TRIM BOARD LH (for Double Cab) |
![]() |
Engage the 2 clips and install the cowl side trim board.
Install the clip.
| 63. INSTALL COWL SIDE TRIM BOARD LH (for Regular Cab) |
![]() |
Engage the 2 clips and install the cowl side trim board.
Install the clip.
| 64. INSTALL COWL SIDE TRIM BOARD LH (for Access Cab) |
![]() |
Engage the 2 clips and install the cowl side trim board.
Install the clip.
| 65. INSTALL COWL SIDE TRIM BOARD RH (for Double Cab) |
| 66. INSTALL COWL SIDE TRIM BOARD RH (for Regular Cab) |
| 67. INSTALL COWL SIDE TRIM BOARD RH (for Access Cab) |
| 68. INSTALL REAR DOOR SCUFF PLATE LH (for Double Cab) |
![]() |
Engage the 8 claws and install the rear door scuff plate.
| 69. INSTALL REAR DOOR SCUFF PLATE LH (for Access Cab) |
![]() |
Engage the 7 claws and install the rear door scuff plate.
| 70. INSTALL REAR DOOR SCUFF PLATE RH (for Double Cab) |
| 71. INSTALL REAR DOOR SCUFF PLATE RH (for Access Cab) |
| 72. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab) |
![]() |
Engage the 9 claws and install the front door scuff plate.
| 73. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab) |
![]() |
Engage the 8 claws and clip, and install the front door scuff plate.
| 74. INSTALL FRONT DOOR SCUFF PLATE LH (for Access Cab) |
![]() |
Engage the 9 claws and clip, and install the front door scuff plate.
| 75. INSTALL FRONT DOOR SCUFF PLATE RH (for Double Cab) |
| 76. INSTALL FRONT DOOR SCUFF PLATE RH (for Regular Cab) |
| 77. INSTALL FRONT DOOR SCUFF PLATE RH (for Access Cab) |
| 78. INSTALL FRONT FLOOR FOOTREST |
![]() |
Engage the 2 clips and install the front floor footrest.
| 79. INSTALL BACK PANEL TRIM (for Regular Cab on Separate Seat Type) |
![]() |
Install the back panel trim with the 4 clips.
| 80. INSTALL BACK PANEL TRIM (for Access Cab) |
![]() |
Engage the 8 claws and 14 clips, and install the back panel trim.
| 81. INSTALL REAR SEAT INNER BELT ASSEMBLY (for Access Cab) |
![]() |
Engage the claw and install the buckle of the rear seat belt inner.
| 82. INSTALL BACK PANEL TRIM COVER (for Regular Cab on Separate Seat Type) |
![]() |
Engage the 4 claws and install the back panel trim cover.
Install the 2 clips.
| 83. INSTALL JACK ASSEMBLY (for Regular Cab on Separate Seat Type) |
| 84. INSTALL BACK PANEL UPPER GARNISH (for Regular Cab) |
![]() |
Engage the 4 claws and 5 clips, and install the back panel upper garnish.
| 85. INSTALL BACK PANEL TRIM COVER (for Regular Cab) |
![]() |
for Separate Seat Type and Bench Seat Type:
Engage the 6 claws and install the back panel trim cover.
![]() |
for Bench Seat Type:
Engage the 6 claws and install the back panel trim cover.
| 86. INSTALL BACK PANEL TRIM COVER (for Access Cab) |
![]() |
Engage the 6 claws and install the back panel trim cover.
| 87. INSTALL LUGGAGE COMPARTMENT SIDE TRAY RH (for Double Cab) |
![]() |
w/ Woofer:
Engage the 5 claws and 7 clips, and install the luggage compartment side tray.
Tighten the bolt.
![]() |
w/o Woofer:
Engage the 5 claws and 5 clips, and install the luggage compartment side tray.
Tighten the 3 bolts.
| 88. INSTALL LUGGAGE COMPARTMENT SIDE TRAY LH (for Double Cab) |
![]() |
Engage the 8 claws and 3 clips, and install the luggage compartment side tray.
Tighten the 3 bolts.
| 89. INSTALL REAR SEAT BACK CENTER HINGE SUB-ASSEMBLY (for Double Cab) |
![]() |
Install the rear seat back center hinge with the 2 bolts.
| 90. INSTALL REAR SEAT BACK HINGE SUB-ASSEMBLY LH (for Double Cab) |
![]() |
Install the rear seat back hinge with the 2 bolts.
| 91. INSTALL REAR SEAT BACK HINGE SUB-ASSEMBLY RH (for Double Cab) |
![]() |
Install the rear seat back hinge with the 2 bolts.
| 92. INSTALL REAR SEAT BACK ASSEMBLY LH (for Double Cab) |
![]() |
Install the rear seat back with the 2 bolts.
| 93. INSTALL REAR SEAT BACK ASSEMBLY RH (for Double Cab) |
![]() |
Install the rear seat back with the 2 bolts.
![]() |
Install the rear seat belt inner and rear seat belt outer center of the floor anchor with the bolt.
| 94. INSTALL REAR SEAT BACK HINGE COVER (for Double Cab) |
for LH Side:
Install the rear seat back hinge cover .
for RH Side:
Install the rear seat back hinge cover .
| 95. INSTALL REAR SEAT CUSHION ASSEMBLY LH (for Double Cab) |
![]() |
Install the rear seat cushion with the 2 bolts.
| 96. INSTALL REAR SEAT CUSHION ASSEMBLY RH (for Double Cab) |
![]() |
Install the rear seat cushion with the 2 bolts.
| 97. INSTALL FRONT SEAT ASSEMBLY LH (for Double Cab) |
![]() |
Place the front seat in the cabin.
Tighten the 2 bolts on the front side of the front seat.
Tighten the 2 bolts on the rear side of the front seat.
![]() |
Install the wire harness clamp.
Connect the 2 connectors.
w/ Front Seat Side Airbag:
Connect the connector.
| 98. INSTALL FRONT SEAT ASSEMBLY RH (for Double Cab) |
![]() |
Place the front seat in the cabin.
Tighten the 2 bolts on the front side of the front seat.
Tighten the 2 bolts on the rear side of the front seat.
![]() |
Install the wire harness clamp.
Connect the connector.
w/ Front Seat Side Airbag:
Connect the connector.
| 99. INSTALL SEAT TRACK COVER LH (for Double Cab) |
![]() |
Engage the 2 claws and install the seat track cover.
| 100. INSTALL SEAT TRACK COVER RH (for Double Cab) |
![]() |
Engage the 2 claws and install the seat track cover.
| 101. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |