Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING ECU

TIRE PRESSURE WARNING ECU > REMOVAL

for Preparation Click here



1. BOLT, SCREW AND NUT TABLE


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabetic codes in the table below.



B085808E01



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. REMOVE FRONT FLOOR FOOTREST


    B087437E01
  1. Disengage the 2 clips and remove the front floor footrest.



4. REMOVE FRONT DOOR SCUFF PLATE LH (for Regular Cab)


    B087476E01
  1. Disengage the 8 claws and clip, and remove the front door scuff plate.



5. REMOVE FRONT DOOR SCUFF PLATE LH (for Access Cab)


    B087436E01
  1. Disengage the 9 claws and clip, and remove the front door scuff plate.



6. REMOVE FRONT DOOR SCUFF PLATE LH (for Double Cab)


    B087411E01
  1. Disengage the 9 claws and remove the front door scuff plate.



7. REMOVE COWL SIDE TRIM BOARD LH (for Regular Cab)


    B087438E01
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board.



8. REMOVE COWL SIDE TRIM BOARD LH (for Access Cab)


    B087438E01
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board.



9. REMOVE COWL SIDE TRIM BOARD LH (for Double Cab)


    B087438E01
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board.



10. REMOVE INSTRUMENT PANEL UNDER TRAY (for Automatic Transmission)


    B085766E01
  1. Disengage the 4 clips and 2 claws, and remove the instrument panel under tray.



11. REMOVE INSTRUMENT PANEL HOLE COVER (for Manual Transmission)


    B085767E01
  1. Disengage the 4 clips and remove the instrument panel hole cover.



12. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type)


    B085768E01
  1. Remove the shift knob.

  1. Disengage the 6 clips and claw, and remove the console upper rear panel sub-assembly.



13. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type)


    B085770E01
  1. Disengage the 4 clips and claw, and remove the console upper rear panel sub-assembly.



14. REMOVE REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type)


    B085771E01
  1. Remove the console box carpet.



    B085772E01
  1. Remove the 2 screws <F> and 2 bolts <B>.

  1. Disengage the 4 claws and remove the rear console box assembly.



15. REMOVE INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type)


    B085773E01
  1. Disengage the 2 clips and 4 claws, and remove the instrument panel cup holder tray.



16. REMOVE FRONT CONSOLE BOX (for Automatic Transmission on Separate Seat Type)


    B085777E01
  1. Remove the 2 screws <F>.

  1. Disengage the 2 clips and claw, and remove the front console box.



17. REMOVE FRONT CONSOLE BOX (for Manual Transmission on Separate Seat Type)


    B085813E01
  1. Remove the shift knob.

  1. Remove the 2 screws <F>.

  1. Disengage the 2 clips and claw, and remove the front console box.



18. REMOVE FRONT CONSOLE BOX (for Automatic Transmission on Bench Seat Type)


    B085810E01
  1. Remove the shift knob.

  1. Remove the box bottom mat.

  1. Remove the instrument panel cup holder.

  1. Remove the No. 2 box bottom mat.



    B085812E01
  1. Remove the clip and 2 bolts <A>.

  1. Disengage the 2 clips and claw, and remove the front console box.



19. REMOVE FRONT CONSOLE BOX (for Manual Transmission on Bench Seat Type)


    B085774E01
  1. Remove the shift knob.

  1. Remove the box bottom mat.

  1. Remove the instrument panel cup holder.

  1. Remove the No. 2 box bottom mat.



    B085776E01
  1. Remove the clip and 2 bolts <A>.

  1. Disengage the 2 clips and claw, and remove the front console box.



20. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    B085778E01
  1. Using a screwdriver, disengage the 4 clips and remove the air conditioning control assembly.

    HINT:
    Tape up the screwdriver tip before use.

  1. Disconnect the 2 connectors.



21. REMOVE RADIO RECEIVER ASSEMBLY


E075957
  1. Remove the 4 bolts.

  1. Disconnect the connector and remove the radio receiver assembly with bracket.



22. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


B088397E01
  1. Disengage the 2 claws.



    B088394
  1. Disconnect the hood lock control cable assembly and remove the hood lock control lever sub-assembly.



23. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    B085780E01
  1. Remove the 2 bolts <B>.

  1. Disengage the 3 clips and remove the lower No. 1 instrument panel finish panel.

  1. Disconnect the connectors.



24. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B085781E01
  1. Remove the 2 clips.

  1. Disengage the 6 clips and remove the instrument cluster finish panel sub-assembly.

  1. Disconnect the connectors.



25. REMOVE INSTRUMENT CLUSTER CENTER FINISH PANEL SUB-ASSEMBLY


    B085784E01
  1. Disengage the 10 clips and remove the instrument cluster center finish panel sub-assembly.



26. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    B085785E01
  1. Disengage the claw and separate the glove compartment door stopper from the glove compartment door assembly.

  1. Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.



    B085786E01
  1. Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.



27. REMOVE INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH


    B085787E01
  1. Remove the bolt <B>.

  1. Disengage the 2 clips and remove the instrument panel lower finish panel sub-assembly RH.



28. REMOVE LOWER INSTRUMENT PANEL LH


    B085788E01
  1. Remove the 3 bolts <B> and the lower instrument panel LH.



29. REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY


    B085789E01
  1. Remove the bolt <B>.

  1. Disengage the 5 clips and remove the instrument lower cover sub-assembly.

  1. Disconnect the 2 connectors.



30. REMOVE TIRE PRESSURE WARNING ECU


C125136
  1. Disconnect the connector.

  1. Remove the 2 screws and the tire pressure warning ECU.