Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › FRONT SEAT CUSHION ASSEMBLY (w/ Occupant Classification ECU, Occupant Classification Sensor)

FRONT SEAT CUSHION ASSEMBLY (w/ Occupant Classification ECU, Occupant Classification Sensor) > REMOVAL

for Preparation Click here


NOTICE:
  1. If the wiring connector of the SRS is disconnected with the ignition switch in the ON position, DTCs will be recorded.
  2. Never use SRS parts from another vehicle. When replacing the parts, replace them with new ones.
  3. Never reuse an occupant classification sensor if an airbag has previously deployed in a collision.
  4. Remove the front seat cushion cover pad and front seat cushion cover together, in order to avoid occupant classification sensor malfunctions.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY
Wait for 90 seconds after disconnecting the cable to prevent the airbag from working.


2. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH


    B121777
  1. Slide the front seat to the most forward position.

  1. Disengage the hook.

  1. Disconnect the 2 connectors.

  1. Using a clip remover, remove the wiring harness clamp.

  1. Remove the wiring harness clamp.

  1. Remove the bolt and the front seat inner belt.



3. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH


    B121778
  1. Slide the front seat to the most forward position.

  1. Disengage the hook.

  1. Disconnect the connector.

  1. Using a clip remover, remove the wiring harness clamp.

  1. Remove the wiring harness clamp.

  1. Remove the bolt and the front seat inner belt.



4. REMOVE FRONT SEAT ASSEMBLY


    B121739
  1. Remove the belt of the front center seat outer belt from the front center seat outer belt guide.



    B121740
  1. Disconnect the 3 connectors.

  1. Using a clip remover, remove the 2 wiring harness clamps.



    B121741
  1. Remove the 4 bolts and the front seat.



5. REMOVE OCCUPANT CLASSIFICATION ECU


    C123157
  1. Disconnect the connector from the the occupant classification ECU.

  1. Remove the 2 bolts and the occupant classification ECU.



6. REMOVE FRONT SEAT HINGE COVER LH


    B121743
  1. Remove the 2 screws and the front seat hinge cover.



7. REMOVE FRONT SEAT HINGE COVER RH

HINT:
Use the same procedure as for the LH side.



8. REMOVE FRONT SEATBACK ASSEMBLY


    B121744
  1. Remove the 4 bolts and the front seat back.



9. REMOVE FRONT SEAT TRACK LOWER FRONT BRACKET LH


    B121750
  1. Remove the nut, the hook and the front seat track front bracket.



10. REMOVE FRONT SEAT TRACK LOWER FRONT BRACKET RH

HINT:
Use the same procedure as for the LH side.



11. REMOVE FRONT SEAT TRACK LOWER REAR BRACKET LH


    B121751
  1. Remove the 2 nuts and the front seat track rear bracket.



12. REMOVE FRONT SEAT TRACK LOWER REAR BRACKET RH

HINT:
Use the same procedure as for the LH side.



13. REMOVE FRONT SEAT OUTER TRACK ASSEMBLY LH


    B121752
  1. Slide the front seat track outer to the most rearward position.

  1. Using "Torx" socket wrench T40, remove the 2 bolts.

  1. Slide the front seat track outer to the most forward position.

  1. Using "Torx" socket wrench T40, remove the 2 bolts and the front seat track outer.



14. REMOVE FRONT SEAT OUTER TRACK ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



15. REMOVE FRONT SEAT CUSHION SPRING ASSEMBLY


    B121753
  1. Remove the 4 hog rings.

  1. Disengage the 10 hooks and remove the front seat cushion spring.



16. REMOVE OCCUPANT CLASSIFICATION SENSOR


    C121182
  1. Disconnect the connector from the occupant classification sensor.

  1. Remove the wiring harness clamp.

  1. Disengage the clamps from the seat cushion frame.

  1. Remove the 2 clips and the occupant classification sensor.