Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



A193170E01

HINT:
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E13-24 (BATT) - E11-12 (E1)
L - BR
Battery (for measuring the battery voltage and for the ECM memory)
Always
11 to 14 V
E11-23 (+BM) - E11-12 (E1)
LG - BR
Power source of throttle motor
Always
11 to 14 V
E14-21 (IGSW) - E11-12 (E1)
BE - BR
Ignition switch
Ignition switch ON
11 to 14 V
E13-22 (+B) - E11-12 (E1)
B - BR
Power source of ECM
Ignition switch ON
11 to 14 V
E13-23 (+B2) - E11-12 (E1)
B - BR
Power source of ECM
Ignition switch ON
11 to 14 V
E10-19 (OC1+) - E10-20 (OC1-)
G-Y - L-B
Camshaft timing oil control valve assembly (bank 1)
Idling
Pulse generation
(See waveform 1)
E9-19 (OC2+) - E9-20 (OC2-)
G-B - L-R
Camshaft timing oil control valve assembly (bank 2)
Idling
Pulse generation
(See waveform 1)
E13-9 (MREL) - E11-12 (E1)
G-W - BR
EFI relay
Ignition switch ON
11 to 14 V
E9-15 (VCV1) - E10-8 (ETHW)
L - BR
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
E9-16 (VCV2) - E10-7 (ETHA)
L-Y - BR
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
E10-14 (VG) - E10-13 (E2G)
R-Y - R-W
Mass air flow meter sub-assembly
Idling, Shift lever position P or N (Neutral), A/C switch off
0.5 to 3.0 V
E10-15 (THA) - E10-7 (ETHA)
R-L - BR
Intake air temperature sensor
Idling, Intake air temperature 20°C (68°F)
0.5 to 3.4 V
E11-17 (THW) - E10-8 (ETHW)
Y-B - BR
Engine coolant temperature sensor
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
E11-15 (VTA1) - E11-14 (ETA)
G-B - W-B
Throttle position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON, Accelerator pedal fully depressed
3.2 to 4.8 V
E11-16 (VTA2) - E11-14 (ETA)
V - W-B
Throttle position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
2.1 to 3.1 V
Ignition switch ON, Accelerator pedal fully depressed
4.6 to 5.0 V
E11-13 (VCTA) - E11-14 (ETA)
R-W - W-B
Power source of throttle position sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
E14-6 (VPA) - E14-3 (EPA)
R-Y - LG-B
Accelerator pedal position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON, Accelerator pedal fully depressed
2.6 to 4.5 V
E14-5 (VPA2) - E14-1 (EPA2)
GR-B - R
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
1.2 to 2.0 V
Ignition switch ON, Accelerator pedal fully depressed
3.4 to 4.7 V
E14-4 (VCPA) - E14-3 (EPA)
R-W - LG-B
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.5 V
E14-2 (VCP2) - E14-1 (EPA2)
L-W - R
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.5 V
E12-17 (HA1A) - E12-16 (E04)
R-W - W-B
Air fuel ratio sensor (bank 1 sensor 1) heater
Idling with warm engine
Pulse generation
(See waveform 2)
Ignition switch ON
11 to 14 V
E12-19 (HA2A) - E12-18 (E05)
B-W - W-B
Air fuel ratio sensor (bank 2 sensor 1) heater
Idling with warm engine
Pulse generation
(See waveform 2)
Ignition switch ON
11 to 14 V
E11-1 (A1A+) - E11-12 (E1)
P - BR
Air fuel ratio sensor (bank 1 sensor 1)
Ignition switch ON
3.3 V*1
E11-7 (A2A+) - E11-12 (E1)
W - BR
Air fuel ratio sensor (bank 2 sensor 1)
Ignition switch ON
3.3 V*1
E11-2 (A1A-) - E11-12 (E1)
L - BR
Air fuel ratio sensor (bank 1 sensor 1)
Ignition switch ON
2.9 V*1
E11-8 (A2A-) - E11-12 (E1)
R - BR
Air fuel ratio sensor (bank 2 sensor 1)
Ignition switch ON
2.9 V*1
E12-12 (HT1B) - E12-11 (E03)
G - W-B
Heated oxygen sensor (bank 1 sensor 2) heater
Idling
Below 3.0 V
Ignition switch ON
11 to 14 V
E12-13 (HT2B) - E12-11 (E03)
L - W-B
Heated oxygen sensor (bank 2 sensor 2) heater
Idling
Below 3.0 V
Ignition switch ON
11 to 14 V
E9-2 (OX1B) - E9-1 (EX1B)
W - BR
Heated oxygen sensor (bank 1 sensor 2)
Maintain engine speed at 2500 rpm for 2 minutes after warming up sensor
Pulse generation
(See waveform 3)
E9-4 (OX2B) - E9-3 (EX2B)
B - BR
Heated oxygen sensor (bank 2 sensor 2)
Maintain engine speed at 2500 rpm for 2 minutes after warming up sensor
Pulse generation
(See waveform 3)
E12-6 (#10) - E12-14 (E01)
E12-1 (#20) - E12-14 (E01)
E12-7 (#30) - E12-14 (E01)
E12-2 (#40) - E12-14 (E01)
E12-8 (#50) - E12-14 (E01)
E12-3 (#60) - E12-14 (E01)
R-L - W-B
B - W-B
R - W-B
G - W-B
Y - W-B
L - W-B
Fuel Injector Assembly
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(See waveform 4)
E10-11 (KNK1) - E10-12 (EKNK)
B - W
Knock sensor (bank 1)
Maintain engine speed at 4000 rpm after warming up engine
Pulse generation
(See waveform 5)
E10-5 (KNK2) - E10-6 (EKN2)
G - R
Knock sensor (bank 2)
Maintain engine speed at 4000 rpm after warming up engine
Pulse generation
(See waveform 5)
E9-9 (VV1+) - E9-10 (VV1-)
R - B-Y
VVT sensor (bank 1)
Idling
Pulse generation
(See waveform 6)
E9-12 (VV2+) - E9-11 (VV2-)
G-W - V
VVT sensor (bank 2)
Idling
Pulse generation
(See waveform 6)
E9-6 (NE+) - E9-5 (NE-)
B - W
Crankshaft position sensor
Idling
Pulse generation
(See waveform 6)
E11-24 (IGT1) - E11-12 (E1)
E11-25 (IGT2) - E11-12 (E1)
E11-26 (IGT3) - E11-12 (E1)
E11-27 (IGT4) - E11-12 (E1)
E11-28 (IGT5) - E11-12 (E1)
E10-25 (IGT6) - E11-12 (E1)
B - BR
P-L - BR
LG - BR
LG-B - BR
R-Y - BR
LG-B - BR
Ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 7)
E11-6 (IGF1) - E11-12 (E1)
W-R - BR
Ignition coil assembly (ignition confirmation signal)
Ignition switch ON
4.5 to 5.5 V
Idling
Pulse generation
(See waveform 7)
E11-18 (PRG) - E11-12 (E1)
Y - BR
Purge VSV
Ignition switch ON
11 to 14 V
Idling, under purge control
Pulse generation
(See waveform 8)
E13-18 (SPD) - E11-12 (E1)
V-W - BR
Speed signal from combination meter
Driving at 20 km/h (12 mph)
Pulse generation
(See waveform 9)
E14-10 (STA) - E11-12 (E1)
B-Y - BR
Starter signal
Cranking
11 to 14 V
E14-18 (STP) - E11-12 (E1)
L - BR
Stop light switch assembly
Brake pedal depressed
7.5 to 14 V
Brake pedal released
Below 1.5 V
E13-8 (ST1-) - E11-12 (E1)
V-W - BR
Stop light switch assembly (opposite to STP terminal)
Ignition switch ON, Brake pedal depressed
Below 1.5 V
Ignition switch ON, Brake pedal released
7.5 to 14 V
E10-2 (NSW)*2 - E11-12 (E1)
V - BR
Park/Neutral position switch assembly
Ignition switch ON, Shift lever position in P or N
Below 3.0 V
Ignition switch ON, Shift lever position other than P and N
11 to 14 V
Cranking
6 to 13 V
E12-20 (M+) - E12-10 (ME01)
P - W-B
Throttle actuator
Idling with warm engine
Pulse generation
(See waveform 10)
E11-29 (M-) - E12-10 (ME01)
L - W-B
Throttle actuator
Idling with warm engine
Pulse generation
(See waveform 11)
E13-3 (FC) - E11-12 (E1)
L-B - BR
Fuel pump control
Ignition switch ON
11 to 14 V
E14-8 (FPR) - E11-12 (E1)
Y-R - BR
Fuel pump relay operation signal (fuel pump assembly control)
Ignition switch ON
11 to 14 V
E13-13 (W) - E11-12 (E1)
BR - BR
MIL
Ignition switch ON
Below 3.0 V
Idling
11 to 14 V
E13-11 (ELS) - E11-12 (E1)
B - BR
Electric load
Taillight switch off
0 to 1.5 V
Taillight switch on
7.5 to 14 V
E13-10 (ELS2) - E11-12 (E1)
B-W - BR
Electric load
Main switch of the voltage inverter off
0 to 1.5 V
Main switch of the voltage inverter on
7.5 to 14 V
E14-28 (TC) - E11-12 (E1)
G - BR
Terminal TC of DLC 3
Ignition switch ON
11 to 14 V
E14-29 (TACH) - E11-12 (E1)
B-W - BR
Engine speed
Idling
Pulse generation
(See waveform 12)
E11-19 (ACIS) - E11-12 (E1)
W-L - BR
VSV for ACIS
Ignition switch ON
11 to 14 V
E10-16 (PSW) - E11-12 (E1)
G-W - BR
P/S pressure switch
Ignition switch ON
11 to 14 V
E14-19 (VPMP) - E11-12 (E1)
V-W - BR
Vent valve
(built into canister pump module)
Ignition switch ON
11 to 14 V
E14-7 (MPMP) - E11-12 (E1)
G - BR
Leak detection pump
(built into canister pump module)
Leak detection pump off
0 to 3 V
Leak detection pump on
11 to 14 V
E10-1 (PPMP) - E10-8 (ETHW)
GR - BR
Canister pressure sensor
(built into canister pump module)
Ignition switch ON
3.0 to 3.6 V
E14-32 (CANH) - E11-12 (E1)
B - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 13)
E14-31 (CANL) - E11-12 (E1)
W - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 14)
E9-26 (AIRV)*3 - E11-12 (E1)
R-W - BR
Air switching valve for secondary air injection system
Ignition Switch ON
11 to 14 V
E10-23 (AIRP)*3 - E11-12 (E1)
V - BR
Air pump control
Ignition Switch ON
11 to 14 V
E11-21 (AIR1)*3 - E11-12 (E1)
L - BR
Air switching valve for secondary air injection system
Ignition Switch ON
11 to 14 V
E10-30 (AIDI)*3 - E11-12 (E1)
G-R - BR
Diagnostic information signal for secondary air injection system
Secondary air injection system operating
Pulse generation
(See waveform 15)
E13-1 (AIP)*3 - E10-8 (ETHW)
B - BR
Secondary air injection system pressure (bank 1) signal
Ignition Switch ON
3.0 to 3.6 V
E13-2 (AIP2)*3 - E10-8 (ETHW)
B-Y - BR
Secondary air injection system pressure (bank 2) signal
Ignition Switch ON
3.0 to 3.6 V
  1. *1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.
  2. *2: for Automatic Transmission
  3. *3: w/ Secondary Air Injection System

WAVEFORM 1
A093229E57
Camshaft Timing Oil Control Valve Signal 
ECM Terminal Name
Between OC1+ and OC1- or OC2+ and OC2-
Tester Range
5 V/DIV, 1 ms/DIV
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 2
A172534E06
Air Fuel Ratio Sensor Heater Signal 
ECM Terminal Name
(a) Between HA1A and E04
(b) Between HA2A and E05
Tester Range
5 V/DIV, 10 ms/DIV
Condition
Idling with warm engine

HINT:
The wavelength varies in accordance with the engine operating condition.


WAVEFORM 3
A088863E53
Heated Oxygen Sensor Signal 
ECM Terminal Name
Between OX1B and EX1B or OX2B and EX2B
Tester Range
200 mV/DIV, 200 ms/DIV
Condition
Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

HINT:
In the Data List, item O2S B1S2 or O2S B2S2 shows the ECM input values from the heated oxygen sensor.


WAVEFORM 4
G035622E18
Fuel Injector Signal 
ECM Terminal Name
Between #10 (to #60) and E01
Tester Range
30 V/DIV, 20 ms/DIV
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 5
A085286E90
Knock Sensor Signal 
ECM Terminal Name
Between KNK1 and EKNK or KNK2 and EKN2
Tester Range
1 V/DIV, 1 ms/DIV
Condition
Engine speed maintained at 4000 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as the engine speed increases.
  2. The waveforms and amplitudes displayed on the tester differ slightly depending on the vehicle.


WAVEFORM 6
G035795E39
  1. Crankshaft position sensor signal

  2. VVT sensor signal
    ECM Terminal Name
    (a) Between NE+ and NE-
    (b) Between VV1+ and VV1- or VV2+ and VV2-
    Tester Range
    2 V/DIV, 20 ms/DIV
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as the engine speed increases.


WAVEFORM 7
G035664E16
  1. Igniter IGT signal (from ECM to igniter)

  2. Igniter IGF signal (from igniter to ECM)
    ECM Terminal Name
    (a) Between IGT (1 to 6) and E1
    (b) Between IGF1 and E1
    Tester Range
    2 V/DIV, 20 ms/DIV
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as the engine speed increases.


WAVEFORM 8
A116415E10
Purge VSV Signal 
ECM Terminal Name
Between PRG and E1
Tester Range
10 V/DIV, 50 ms/DIV
Condition
Idling, under purge control

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 9
A093224E35
Vehicle Speed Signal 
ECM Terminal Name
Between SPD and E1
Tester Range
2 V/DIV, 20 ms/DIV
Condition
Driving at 20 km/h (12 mph)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 10
A208000E14
Throttle Actuator Positive Terminal Signal 
ECM Terminal Name
Between M+ and ME01
Tester Range
5 V/DIV, 1 ms/DIV
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 11
A208001E04
Throttle Actuator Negative Terminal Signal 
ECM Terminal Name
Between M- and ME01
Tester Range
5 V/DIV, 1 ms/DIV
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 12
A093225E46
Engine Speed Signal 
ECM Terminal Name
Between TACH and E1
Tester Range
5 V/DIV, 10 ms/DIV
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 13
A086154E64
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANH and E1
Tester Range
1 V/DIV, 10 μs/DIV
Condition
Stop engine and ignition switch to ON

HINT:
The wavelength varies depending on the CAN communication signal.


WAVEFORM 14
A086155E58
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANL and E1
Tester Range
1 V/DIV, 10 μs/DIV
Condition
Stop engine and ignition switch to ON

HINT:
The wavelength varies depending on the CAN communication signal.


WAVEFORM 15
A100214E04
Terminal DI Signal of air injection control driver 
ECM Terminal Names
Between AIDI and E1
Tester Range
5 V/DIV, 50 ms/DIV
Conditions
Secondary air injection system operation

HINT:
The wavelength change when the air injection control driver detects malfunctions in the air injection system (Click here).