Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > FREEZE FRAME DATA

for Preparation Click here



DESCRIPTION
Freeze frame data record the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was running or stopped, the engine was warmed up or not, the air fuel ratio was Lean or Rich, and other data, from the time the malfunction occurred.
These data sets can be used to simulate the conditions of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.
A159471E11

HINT:
If it is impossible to replicate the problem even through a DTC is detected, confirm the freeze frame data.
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the Techstream five separate sets of freeze frame data, including the data values at the time when the DTC was stored, can be checked.

  1. 3 data sets before the DTC was stored
  2. 1 data set when the DTC was stored
  3. 1 data set after the DTC was stored

LIST OF FREEZE FRAME DATA

Tester Display
Measurement Item
Diagnostic Note
Vehicle Speed
Vehicle speed
Speed indicated on speedometer.
Engine Speed
Engine speed
-
Calculate Load
Calculated load
Calculated load by ECM.
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If the mass air flow volume is approximately 0.0 gm/sec:
  1. The mass air flow meter power source circuit is open or short.
  1. The VG circuit is open or short.
If the mass air flow volume is 271.0 gm/sec or more:
  1. The E2G circuit is open.
Atmosphere Pressure
Atmosphere pressure
-
Coolant Temp
Engine coolant temperature
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is higher than 135°C (275°F), the sensor circuit is shorted.
Intake Air
Intake air temperature
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is higher than 128°C (262°F), the sensor circuit is shorted.
Engine Run Time
Accumulated engine running time
-
Initial Engine Coolant Temp
Engine coolant temperature at engine start
-
Initial Intake Air Temp
Intake air temperature at engine start
-
Battery Voltage
Battery voltage
-
Accel Sens. No.1 Volt %
Absolute accelerator pedal position No. 1
-
Accel Sens. No.2 Volt %
Absolute accelerator pedal position No. 2
-
Throttle Sensor Volt %
Throttle sensor positioning
-
Throttle Sensor #2 Volt %
Throttle sensor positioning #2
-
Throttle Sensor Position
Throttle sensor positioning
-
Throttle Motor DUTY
Throttle motor
-
Throttle Position
Throttle position
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
ISC Flow
Flow rate calculated using information from each sensor
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
ISC Position
Requested opening amount calculated using ISC control
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
This is the throttle valve opening amount while the engine is idling (the throttle valve opening amount necessary to maintain ISC air flow).
ISC Feedback Value
ISC feedback compensation amount
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
ISC Learning Value
ISC learned compensation amount
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Electric Load Feedback Val
Compensation flow rate according to electrical load
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Air Conditioner FB Val
Compensation flow rate according to air conditioner load
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
PS Feedback Val
Compensation flow rate according to power steering load
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Low Revolution Control
Low engine speed control operation state
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
N Range Status
Shift lever N status
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Eng Stall Control FB Flow
Intake air compensation flow rate
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Deposit Loss Flow
Flow loss due to deposits
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Injector (Port)
Injection period of No. 1 cylinder
-
Injection Volum (Cylinder 1)
Injection volume
-
Fuel Pump Speed Control
Fuel pump speed control status
-
Fuel Pump/Speed Status
Fuel pump/speed status
-
Vacuum Pump
Key-off EVAP system leak detection pump status
Refer to the EVAP System
(Click here).
Current Fuel Type
Current fuel type
Used to identify the current fuel type:
Gasoline
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
Purge Density Learn Value
Learning value of purge density
-
EVAP System Vent Value
Key-off EVAP system vent valve status
-
EVAP Purge VSV
EVAP Purge VSV
-
Purge Cut VSV Duty
Purge cut VSV duty
-
Target Air-Fuel Ratio
Ratio compared to stoichiometric level
-
AF Lambda B1S1
Fuel trim at air fuel ratio sensor
-
AF Lambda B2S1
Fuel trim at air fuel ratio sensor
-
AFS Voltage B1S1
AFS Voltage B2S1
Air fuel ratio sensor output
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS Current B1S1
Air fuel ratio sensor current (bank 1)
-
AFS Current B2S1
Air fuel ratio sensor current (bank 2)
-
A/F Heater Duty #1
Air fuel ratio heater duty ratio (bank 1)
-
A/F Heater Duty #2
Air fuel ratio heater duty ratio (bank 2)
-
O2S B1S2
O2S B2S2
Heated oxygen sensor output
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
O2S Impedance B1S2
O2S Impedance B2S2
Heated oxygen sensor impedance
-
O2 Heater B1S2
Heated oxygen sensor heater (bank 1)
-
O2 Heater B2S2
Heated oxygen sensor heater (bank 2)
-
O2 Heater Curr Val B1S2
Heated oxygen sensor current (bank 1)
-
O2 Heater Curr Val B2S2
Heated oxygen sensor current (bank 2)
-
Short FT #1
Short-term fuel trim (bank 1)
Short-term fuel compensation is used to maintain the air fuel ratio at the stoichiometric air fuel ratio.
Long FT #1
Long-term fuel trim (bank 1)
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
Total FT #1
Total fuel trim (bank 1)
-
Short FT #2
Short-term fuel trim
Short-term fuel compensation is used to maintain the air fuel ratio at the stoichiometric air fuel ratio.
Long FT #2
Long-term fuel trim (bank 2)
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
Total FT #2
Total fuel trim (bank 2)
-
Fuel System Status #1
Fuel system status (bank 1)
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the air fuel ratio sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
Fuel System Status #2
Fuel system status (bank 2)
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the air fuel ratio sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
Air Pump Pressure (Absolute)
Air pump pressure (bank 1)
-
Air Pump2 Pressure (Absolute)
Air pump pressure (bank 2)
-
Air Pump Pulsation Pressure
Air pump pulsation pressure
-
Secondary Air Control VSV
Secondary air injection system status
-
AI Test
Secondary air injection system operation prohibition
-
IGN Advance
Ignition advance
-
Knock Feedback Value
Feedback value of knocking
-
Knock Correct Learn Value
Correction learning value of knocking
-
Idle Spark Advn Ctrl #1
Individual cylinder timing advance compensation amount (No. 1)
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #2
Individual cylinder timing advance compensation amount (No. 2)
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #3
Individual cylinder timing advance compensation amount (No. 3)
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #4
Individual cylinder timing advance compensation amount (No. 4)
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #5
Individual cylinder timing advance compensation amount (No. 5)
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #6
Individual cylinder timing advance compensation amount (No. 6)
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
ACIS VSV
VSV for Acoustic Control Induction System (ACIS)
-
Actual VVT Angle #1
Actual VVT angle (bank 1)
-
Actual VVT Angle #2
Actual VVT angle (bank 2)
-
VVT Control Status #1
VVT control status
-
VVT Control Status #2
VVT control status
-
VVT Advance Fail
VVT control failure status
-
Catalyst Temp B1S1
Catalyst Temp B2S1
Estimated catalyst temperature (sensor 1)
-
Catalyst Temp B1S2
Catalyst Temp B2S2
Estimated catalyst temperature (sensor 2)
-
Starter Signal
Starter switch signal
-
Power Steering Signal
Power steering switch status
-
Neutral Position SW Signal*1
Park/Neutral position switch signal
-
Clutch Switch*2
Clutch Switch status
-
4WD SW*3
4WD switch status
-
Transfer L4*1
Transfer L4 switch status
-
Stop Light Switch
Stop light switch
-
A/C Signal
A/C signal
-
Closed Throttle Position SW
Closed throttle position switch
-
Fuel Cut Condition
Fuel cut condition
-
Immobiliser Communication
Immobiliser communication
-
TC Terminal
TC terminal status
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance from DTC cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared
-
Dist Batt Cable Disconnect
Accumulated distance from battery cable disconnected
-
IG OFF Elapsed Time
Cumulative time after ignition switch off
-
TC and TE1
TC and CG (TE1) terminals of DLC3
-
Ignition Trig. Count
Ignition counter
-
Cylinder #1 Misfire Count
Cylinder #1 misfire count
-
Cylinder #2 Misfire Count
Cylinder #2 misfire count
-
Cylinder #3 Misfire Count
Cylinder #3 misfire count
-
Cylinder #4 Misfire Count
Cylinder #4 misfire count
-
Cylinder #5 Misfire Count
Cylinder #5 misfire count
-
Cylinder #6 Misfire Count
Cylinder #6 misfire count
-
All Cylinders Misfire Count
All cylinders misfire count
-
Misfire RPM
Engine speed when misfire occurred
-
Misfire Load
Engine load when misfire occurred
-
Misfire Margin
Margin to detect engine misfire
-
Catalyst OT MF F/C
Fuel cut to prevent catalyst from overheating during misfire
-
Cat OT MF F/C History
History of fuel cut to prevent catalyst from overheating during misfire
-
Cat OT MF F/C Cylinder#1
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#2
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#3
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#4
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#5
Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#6
Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)
-
Engine Speed (Starter Off)
Engine speed when starter off
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Starter Count
Number of times starter turned on after ignition switch turned to ON
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Run Dist of Previous Trip
Distance driven during previous trip
Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.

HINT:
Run Dist of Previous Trip in the freeze frame data present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of the Data List (real-time measurements), or for freeze frame data present when DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.

Engine Starting Time
Time elapsed after engine started (interval between ignition switch ON and off)
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Previous Trip Coolant Temp
Engine coolant temperature during previous trip
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Previous Trip Intake Temp
Intake air temperature during previous trip
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Engine Oil Temperature
Engine oil temperature (estimated temperature)
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Previous Trip Eng Oil Temp
Engine oil temperature during previous trip
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Ambient Temp for A/C
Ambient temperature for A/C
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Previous Trip Ambient Temp
Ambient temperature during previous trip
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Engine Start Hesitation
History of hesitation during engine start
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Low Rev for Eng Start
History of low engine speed after engine start
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
Minimum Engine Speed
Minimum engine speed
Reference:
Check the value when the engine stalls, is difficult to start, or idles roughly
A/F Learn Value Idle #1
Air fuel ratio learned value for idling (bank 1)
-
A/F Learn Value Low #1
Air fuel ratio learned value for low engine loads (bank 1)
-
A/F Learn Value Mid1 #1
Air fuel ratio learned value for mid-sized engine loads 1 (bank 1)
-
A/F Learn Value Mid2 #1
Air fuel ratio learned value for mid-sized engine loads 2 (bank 1)
-
A/F Learn Value High #1
Air fuel ratio learned value for high engine loads (bank 1)
-
A/F Learn Value Idle #2
Air fuel ratio learned value for idling (bank 2)
-
A/F Learn Value Low #2
Air fuel ratio learned value for low engine loads (bank 2)
-
A/F Learn Value Mid1 #2
Air fuel ratio learned value for mid-sized engine loads 1 (bank 2)
-
A/F Learn Value Mid2 #2
Air fuel ratio learned value for mid-sized engine loads 2 (bank 2)
-
A/F Learn Value High #2
Air fuel ratio learned value for high engine loads (bank 2)
-
ACT VSV
A/C cut status for Active Test
-
Brake Override System
Brake override system status
-
Idle Fuel Cut
Fuel cut idle
ON: when the throttle valve is fully closed and the engine speed is more than 3500 rpm.
FC TAU
Fuel cut during very light load
Fuel cut being performed under a very light load to prevent the engine combustion from becoming incomplete.
Immobiliser Fuel Cut
Status of immobiliser fuel cut
-
Immobiliser Fuel Cut History
Status of the immobiliser fuel cut history
-
Electrical Load Signal 1
Electrical load signal
-
Electrical Load Signal 2
Electrical load signal
-
A/F Sensor Determination (worst value) #1
Worst judgment value of air fuel ratio sensor output (bank 1)
-
A/F Sensor Determination (worst value) #2
Worst judgment value of air fuel ratio sensor output (bank 2)
-
Engine Speed Fluctuation Avg (worst value) #1
Worst value of average engine speed fluctuation (Cylinder 1)
-
Engine Speed Fluctuation Avg (worst value) #2
Worst value of average engine speed fluctuation (Cylinder 2)
-
Engine Speed Fluctuation Avg (worst value) #3
Worst value of average engine speed fluctuation (Cylinder 3)
-
Engine Speed Fluctuation Avg (worst value) #4
Worst value of average engine speed fluctuation (Cylinder 4)
-
Engine Speed Fluctuation Avg (worst value) #5
Worst value of average engine speed fluctuation (Cylinder 5)
-
Engine Speed Fluctuation Avg (worst value) #6
Worst value of average engine speed fluctuation (Cylinder 6)
-
SPD (NT)*1
Input shaft speed
Data is displayed in increments of 50 rpm.
SPD (SP2)*1
Output shaft speed
-
  1. *1: for Automatic Transmission
  2. *2: for Manual Transmission
  3. *3: for 4WD

FOR MEXICO MODELS 
Tester Display
Measurement Item
Diagnostic Note
Injector (port)
Injection period of No. 1 cylinder
-
IGN Advance
Ignition advance
-
Calculate Load
Calculated load
Calculated load by ECM
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If the mass air flow volume is approximately 0.0 gm/sec:
  1. The mass air flow meter power source circuit is open or short.
  1. The VG circuit is open or short.
If the mass air flow volume is 271.0 gm/sec or more:
  1. The E2G circuit is open.
Engine Speed
Engine speed
-
Vehicle Speed
Vehicle speed
Speed indicated on speedometer
Coolant Temp
Engine coolant temperature
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is higher than 135°C (275°F), the sensor circuit is shorted.
Intake Air
Intake air temperature
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is higher than 128°C (262°F), the sensor circuit is shorted.
Air-Fuel Ratio
Ratio compared to stoichiometric level
-
Purge Density Learn Value
Learning value of purge density
-
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Knock Correct Learn Value
Correction learning value of knocking
-
Knock Feedback Value
Feedback value of knocking
-
Accelerator Position No. 1
Absolute accelerator pedal position No. 1
-
Accelerator Position No. 2
Absolute accelerator pedal position No. 2
-
Throttle Position
Absolute throttle position
-
Throttle Sensor Position
Throttle sensor positioning
-
Throttle Sensor Position #2
Absolute throttle sensor positioning #2
-
Throttle Motor DUTY
Throttle motor
-
O2S B1S2
O2S B2S2
Heated oxygen sensor output
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS B1S1
AFS B2S1
Air fuel ratio sensor output
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS B2S1
Air fuel ratio sensor current
-
Total FT #1
Total fuel trim (bank 1)
-
Total FT #2
Total fuel trim (bank 2)
-
Short FT #1
Short-term fuel trim (bank 1)
Short-term fuel compensation is used to maintain the air fuel ratio at the stoichiometric air fuel ratio.
Long FT #1
Long-term fuel trim (bank 1)
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
Short FT #2
Short-term fuel trim (bank 2)
Short-term fuel compensation is used to maintain the air fuel ratio at the stoichiometric air fuel ratio.
Long FT #2
Long-term fuel trim (bank 2)
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
Fuel System Status (Bank1)
Fuel system status (bank 1)
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the air fuel ratio sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
Fuel System Status (Bank2)
Fuel system status (bank 2)
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the air fuel ratio sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
O2FT B1S2
Fuel trim at heated oxygen sensor
-
O2FT B2S2
Fuel trim at heated oxygen sensor
-
AF Lambda B1S1
Fuel trim at air fuel ratio sensor
-
AFS B1S1
Air fuel ratio sensor current
-
AF FT B2S1
Fuel trim at air fuel ratio sensor
-
Catalyst Temp (B1S1)
Catalyst Temp (B2S1)
Estimated catalyst temperature (sensor 1)
-
Catalyst Temp (B1S2)
Catalyst Temp (B2S2)
Estimated catalyst temperature (sensor 2)
-
Sub O2S Impedance B1S2
Sub O2S Impedance B2S2
Heated oxygen sensor impedance
-
Initial Engine Coolant Temp
Engine coolant temperature at engine start
-
Initial Intake Air Temp
Intake air temperature at engine start
-
Injection Volum (Cylinder1)
Injection volume
-
Starter Signal
Starter switch signal
-
Power Steering Switch
Power steering switch
-
Power Steering Signal
Power steering signal (history)
-
Closed Throttle Position SW
Closed throttle position switch
-
A/C Signal
A/C signal
-
Neutral Position SW Signal
Park/Neutral position switch signal
-
Electrical Load Signal
Electrical load signal
-
Stop Light Switch
Stop light switch
-
Battery Voltage
Battery voltage
-
Atmosphere Pressure
Atmosphere pressure
-
Fuel Pump Speed Control
Fuel pump speed control status
-
ACIS VSV
VSV for Acoustic Control Induction System (ACIS)
-
ACT VSV
A/C cut status for Active Test
-
VVT Control Status (Bank2)
VVT control status (bank 2)
-
EVAP Purge VSV
EVAP Purge VSV
-
Fuel Pump/Speed Status
Fuel pump/speed status
-
VVT Control Status (Bank1)
VVT control status (bank 1)
-
Vacuum Pump
Key-off EVAP system leak detection pump status
Refer to EVAP System
(Click here)
EVAP System Vent Valve
Key-off EVAP system vent valve status
-
TC and TE1
TC and CG (TE1) terminals of DLC3
-
Engine Speed of Cyl #1
Engine speed for cylinder 1
-
Engine Speed of Cyl #2
Engine speed for cylinder 2
-
Engine Speed of Cyl #3
Engine speed for cylinder 3
-
Engine Speed of Cyl #4
Engine speed for cylinder 4
-
Engine Speed of Cyl #5
Engine speed for cylinder 5
-
Engine Speed of Cyl #6
Engine speed for cylinder 6
-
Av Engine Speed of All Cyl
Engine speed for all cylinders
-
VVT Aim Angle (Bank1)
VVT aim angle (bank 1)
-
VVT Change Angle (Bank1)
VVT change angle (bank 1)
-
VVT OCV Duty (Bank1)
VVT OCV operation duty (bank 1)
-
VVT Aim Angle (Bank2)
VVT aim angle (bank 2)
-
VVT Change Angle (Bank2)
VVT change angle (bank 2)
-
VVT OCV Duty (Bank2)
VVT OCV operation duty (bank 2)
-
Idle Fuel Cut
Fuel cut idle
ON: when throttle valve fully closed and the engine speed is more than 3500 rpm
FC TAU
Fuel cut during very light load
Fuel cut being performed under very light load to prevent the engine combustion from becoming incomplete
Ignition
Ignition counter
-
Cylinder #1 Misfire Count
Cylinder #1 misfire count
-
Cylinder #2 Misfire Count
Cylinder #2 misfire count
-
Cylinder #3 Misfire Count
Cylinder #3 misfire count
-
Cylinder #4 Misfire Count
Cylinder #4 misfire count
-
Cylinder #5 Misfire Count
Cylinder #5 misfire count
-
Cylinder #6 Misfire Count
Cylinder #6 misfire count
-
All Cylinders Misfire Count
All cylinders misfire count
-
Misfire RPM
Engine speed when misfire occurred
-
Misfire Load
Engine load when misfire occurred
-
Misfire Margin
Margin to detect engine misfire
-
Catalyst OT MF F/C
Fuel cut to prevent catalyst from overheating during misfire
-
Cat OT MF F/C History
History of fuel cut to prevent catalyst from overheating during misfire
-
Cat OT MF F/C Cylinder #1
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder #2
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder #3
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder #4
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder #5
Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder #6
Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)
-
Engine Run Time
Accumulated engine running time
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance from DTC cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared
-