Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › THROTTLE BODY

THROTTLE BODY > INSTALLATION

for Preparation Click here



1. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Install a new gasket and the throttle with motor body with the 4 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 9 ft.*lbf }

  1. Connect the throttle motor connector.

  1. Connect the water by-pass hose No. 4.

  1. Connect the water by-pass hose No. 5.



2. INSTALL AIR CLEANER ASSEMBLY
  1. Install the air cleaner with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the ventilation hose No. 2.



3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



4. ADD ENGINE COOLANT
  1. Pour coolant into the radiator until it overflows.

    Capacity:

    Transmission
    Capacity
    Manual Transmission
    9.7 liters (10.3 Us qts, 8.5 Imp. qts)
    Automatic Transmission
    9.8 liters (10.4 Us qts, 8.6 Imp. qts)

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    3. New Toyota vehicles are filled with Toyota Super Long Life Coolant (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)). When replacing the coolant, Toyota Super Long Life Coolant is recommended.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Check the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.

  1. Install the radiator cap securely.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Condition
      Fan Speed
      Any setting except OFF
      Temperature
      Toward WARM
      Air Conditioning Switch
      OFF

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Squeeze the inlet and outlet radiator hoses several times by hand while warming up the engine.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, perform the steps from (a) through (h) and repeat the operation until the coolant level remains at the full level.

  1. Check the coolant level inside the radiator reservoir tank again. If it is below the full level, add coolant.



5. CHECK FOR ENGINE COOLANT LEAKAGE
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Pump it to 118 kPa (1.2 kgf/cm2 17.1 psi), then check for leakage.



6. INSTALL V-BANK COVER
  1. Install the V-bank cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



7. PERFORM INITIALIZATION

NOTICE:
Perform the following procedure after replacing the ECM, throttle body assembly or any throttle body components or after cleaning the throttle body.

  1. Disconnect the cable from the negative (-) battery terminal. Wait at least 60 seconds and reconnect the cable.

  1. Turn the ignition switch to the ON position without operating the accelerator pedal.

    NOTICE:
    If the accelerator pedal is operated, perform the above steps again.

  1. Connect the tester to the DLC3 and clear the DTCs (Click here).

  1. Start the engine and check that the MIL is not illuminated and that the idle speed is within the specified range when the A/C is switched off after the engine is warmed up.

    Standard:
    Condition
    Engine Idle Speed
    A/C switched off
    650 to 750 rpm

    NOTICE:
    1. Be sure to perform this step with all accessories off.
    2. Make sure that the shift lever is in N or P.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value is 60% or more.

  1. Perform a road test and confirm that there are no abnormalities.