Home › ENGINE ยท 2TR-FE › FUEL › FUEL INJECTOR

FUEL INJECTOR > REMOVAL

for Preparation Click here




1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY NO.1


4. DRAIN ENGINE COOLANT

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. Remove the 4 bolts, then remove the engine under cover No. 1. (PRE RUNNER AND 4WD TYPE)



    G038197E01
  1. Install a vinyl hose onto the radiator side.



    G038198E01
  1. Install a vinyl hose onto the engine side.



    G038199E01
  1. Loosen the engine drain plug.

  1. Loosen the radiator drain plug.

  1. Remove the radiator cap and drain coolant.

  1. Drain the coolant from the reservoir tank.



5. REMOVE INTAKE AIR CONNECTOR


G037694E01
  1. Disconnect the pressure sensor connector.

  1. Disengage the wire harness clamp.

  1. Disconnect the vacuum hose.



    G037695E01
  1. Disconnect the No. 2 ventilation hose.



    G037696E01
  1. Disconnect the vacuum hose.



    G037697E01
  1. Loosen the 2 hose clamp bolts.

  1. Remove the 3 bolts, then remove the intake air connector.



6. REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY


G037698E01
  1. Disconnect the water by-pass hose.

  1. Disconnect the No. 2 water by-pass hose.

  1. Disconnect the throttle motor connector.



    G037699E01
  1. Remove the 2 bolts and 2 nuts, then remove the throttle with motor body.



    G037700E01
  1. Remove the gasket from the intake manifold.



7. DISCONNECT FUEL HOSE


G037900E01
  1. Pull the checker of the fuel hose upward.

  1. Pinch the detaching switch of the fuel hose connector and pull out the fuel hose.

    NOTICE:
    1. Remove any dirt and foreign objects on the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.

    3. G037901E01
      Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel hose.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



8. DISCONNECT NO. 2 FUEL HOSE


G037902E01
  1. Pull the checker of the fuel hose upward.

  1. Pinch the detaching switch of the fuel hose connector and pull out the fuel hose.

    NOTICE:
    1. Remove any dirt and foreign objects on the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.

    3. G037901E01
      Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel hose.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



9. REMOVE FUEL PRESSURE PULSATION DAMPER ASSEMBLY


G037905E01
  1. Remove the 2 bolts, then remove the fuel pressure pulsation damper.



10. REMOVE FUEL DELIVERY PIPE WITH INJECTOR


G037714E01
  1. Disconnect the 4 injector connectors.

  1. Disconnect the VSV connector.

  1. Disconnect the engine wire harness clamp.



    G037715E01
  1. Disconnect the compressor magnetic clutch connector. (with AIR CONDITIONING)

  1. Disconnect the wire harness clamp.

  1. Remove the bolt, then remove the harness clamp bracket.



    G037716E01
  1. Remove the 2 bolts, then remove the fuel delivery pipe together with the fuel injectors.

    NOTICE:
    Be careful not to drop the fuel injectors when removing the fuel delivery pipe.



    G037894E01
  1. Remove the 2 delivery pipe No. 1 spacers.

  1. Remove the 4 injector vibration insulators.

  1. Using a screwdriver, remove the 4 spacers.



11. REMOVE FUEL INJECTOR ASSEMBLY


G037895E01
  1. Pull the 4 fuel injectors out of the fuel delivery pipe.