ENGINE IMMOBILISER SYSTEM > TERMINALS OF ECU |
| CHECK TRANSPONDER KEY AMPLIFIER |

Disconnect the T9 amplifier connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| T9-7 (AGND) - Body ground | L - Body ground | Ground | Always | Below 1 Ω |
Reconnect the T9 amplifier connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| T9-1 (VC5) - T9-7 (AGND) | GR-B - L | Power source | No key in ignition key cylinder | Below 1 V |
| T9-1 (VC5) - T9-7 (AGND) | GR-B - L | Power source | Key inserted | 4.6 to 5.4 V |
| T9-4 (CODE) - T9-7 (AGND) | P-G - L | Demodulated signal of key code data | No key in ignition key cylinder → Key inserted | Pulse generation (see waveform 1) |
| T9-5 (TXCT) - T9-7 (AGND) | LG-R - L | Key code output signal | No key in ignition key cylinder → Key inserted | Pulse generation (see waveform 2) |
| T9-7 (AGND) - Body ground | L - Body ground | Ground | Always | Below 1 Ω |
Inspect using an oscilloscope.
![]() |
Waveform 1
| Tester Connection | T9-4 (CODE) - T9-7 (AGND) |
| Tool Setting | 2 V/DIV., 20 msec/DIV. |
| Condition | No key in ignition key cylinder → Key inserted |
![]() |
Waveform 2
| Tester Connection | T9-5 (TXCT) - T9-7 (AGND) |
| Tool Setting | 2 V/DIV., 20 msec/DIV. |
| Condition | No key in ignition key cylinder → Key inserted |
| CHECK TRANSPONDER KEY ECU ASSEMBLY |

Disconnect the T10 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| T10-16 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| T10-1 (+B) - T10-16 (GND) | R - W-B | Battery | Always | 11 to 14 V |
| T10-2 (IG) - T10-16 (GND) | BE - W-B | Ignition switch | Ignition switch OFF | Below 1 V |
| T10-2 (IG) - T10-16 (GND) | BE - W-B | Ignition switch | Ignition switch ON | 11 to 14 V |
| T10-3 (KSW) - T10-5 (AGND) | G-B - L | Unlock warning switch | No key in ignition key cylinder | 10 kΩ or higher |
| T10-3 (KSW) - T10-5 (AGND) | G-B - L | Unlock warning switch | Key inserted | Below 1Ω |
Reconnect the T10 ECU connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| T10-14 (VC5) - T10-16 (GND) | GR-B - W-B | Power source | No key in ignition key cylinder | 0 V |
| T10-14 (VC5) - T10-16 (GND) | GR-B - W-B | Power source | Key inserted | 4.6 to 5.4 V |
| T10-4 (TXCT) - T10-16 (GND) | LG-R - W-B | Transponder key amplifier communication signal | No key in ignition key cylinder → Key inserted | Pulse generation (see waveform 1) |
| T10-15 (CODE) - T10-16 (GND) | P-G - W-B | Transponder key amplifier communication signal | No key in ignition key cylinder → Key inserted | Pulse generation (see waveform 2) |
| T10-13 (EFIO) - T10-16 (GND) | L-W - W-B | ECM output signal | Ignition switch OFF → ON | Pulse generation (see waveform 3) |
| T10-12 (EFII) - T10-16 (GND) | LG-B - W-B | ECM input signal | Ignition switch off | 11 to 14 V |
| Within 3 seconds after starter operates and initial combustion occurs, or within 3seconds after ignition switch first turned on (IG) after battery disconnected and connected. | Pulse generation (see waveform 4) |
Inspect using an oscilloscope.
![]() |
Waveform 1
| Tester Connection | T10-4 (TXCT) - T10-16 (GND) |
| Tool Setting | 2.5 V/DIV., 20 msec/DIV. |
| Condition | No key in ignition key cylinder → Key inserted |
![]() |
Waveform 2
| Tester Connection | T10-15 (CODE) - T10-16 (GND) |
| Tool Setting | 2.5 V/DIV., 20 msec/DIV. |
| Condition | No key in ignition key cylinder → Key inserted |
![]() |
Waveform 3
| Tester Connection | T10-13 (EFIO) - T10-16 (GND) |
| Tool Setting | 12 V/DIV., 100 msec/DIV. |
| Condition | Ignition switch OFF → ON |
![]() |
Waveform 4
| Tester Connection | T10-12 (EFII) - T10-16 (GND) |
| Tool Setting | 5 V/DIV., 500 ms/DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3seconds after ignition switch first turned on (IG) after battery disconnected and connected. |
| CHECK ECM (for 2TR-FE) |

Disconnect the E4 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E4-3 (E1) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
Reconnect the E4 ECM connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E7-16 (IMI) - E4-3 (E1) | L-W - BR | Transponder key ECU input signal | Ignition switch off | Below 1 V |
| Ignition switch on | Pulse generation (see waveform 1) | |||
| E7-15 (IMO) - E4-3 (E1) | LG-B - BR | Transponder key ECU output signal | Ignition switch off | 11 to 14 V |
| Within 3 seconds after starter operates and initial combustion occurs, or within 3seconds after ignition switch first turned on (IG) after battery disconnected and connected. | Pulse generation (see waveform 2) |
Inspect using an oscilloscope.
![]() |
Waveform 1
| Tester Connection | E7-16 (IMI) - E4-3 (E1) |
| Tool Setting | 10 V/DIV., 100 msec/DIV. |
| Condition | Ignition switch on |
![]() |
Waveform 2
| Tester Connection | E7-15 (IMO) - E4-3 (E1) |
| Tool Setting | 5 V/DIV., 500 msec/DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3seconds after ignition switch first turned on (IG) after battery disconnected and connected. |
| CHECK ECM (for 1GR-FE) |

Disconnect the E11 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E11-12 (E1) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
Disconnect the E11 ECM connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E14-14 (IMI) - E11-12 (E1) | L-W - BR | Transponder key ECU input signal | Ignition switch off | Below 1 V |
| Ignition switch on | Pulse generation (see waveform 1) | |||
| E14-20 (IMO) - E11-12 (E1) | LG-B - BR | Transponder key ECU output signal | Ignition switch off | 11 to 14 V |
| Within 3 seconds after starter operates and initial combustion occurs, or within 3seconds after ignition switch first turned on (IG) after battery disconnected and connected. | Pulse generation (see waveform 2) |
Inspect using an oscilloscope.
![]() |
Waveform 1
| Tester Connection | E14-14 (IMI) - E11-12 (E1) |
| Tool Setting | 10 V/DIV., 100 msec/DIV. |
| Condition | Ignition switch on |
![]() |
Waveform 2
| Tester Connection | E14-20 (IMO) - E11-12 (E1) |
| Tool Setting | 5 V/DIV., 500 msec/DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3seconds after ignition switch first turned on (IG) after battery disconnected and connected. |