Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



C121776E13

HINT:
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E8-3 (BATT) - E4-3 (E1)
L - BR
Battery (for measuring battery voltage and for ECM memory)
Always
11 to 14 V
E8-7 (+BM) - E4-3 (E1)
LG - BR
Power source of throttle motor
Always
11 to 14 V
E8-9 (IGSW) - E4-3 (E1)
BE - BR
Ignition switch
Ignition switch ON
11 to 14 V
E8-1 (+B) - E4-3 (E1)
B - BR
Power source of ECM
Ignition switch ON
11 to 14 V
E8-8 (MREL) - E4-3 (E1)
G-W - BR
EFI relay
Ignition switch ON
11 to 14 V
E4-18 (VC) - E4-28 (E2)
L - BR
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.0 V
E4-20 (VTA1) - E4-28 (E2)
G-B - BR
Throttle position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON, Accelerator pedal fully depressed
3.2 to 4.8 V
E4-19 (VTA2) - E4-28 (E2)
G-W - BR
Throttle position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
2.1 to 3.1 V
Ignition switch ON, Accelerator pedal fully depressed
4.6 to 5.0 V
E8-18 (VPA) - E8-20 (EPA)
R-Y - LG-B
Accelerator pedal position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON, Accelerator pedal fully depressed
2.6 to 4.5 V
E8-19 (VPA2) - E8-21 (EPA2)
GR-B - R
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
1.2 to 2.0 V
Ignition switch ON, Accelerator pedal fully depressed
3.4 to 5.0 V
E8-26 (VCPA) - E8-20 (EPA)
R-W - LG-B
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.0 V
E8-27 (VCP2) - E8-21 (EPA2)
L-W - R
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.0 V
E4-10 (ALT) - E4-3 (E1)
L - BR
Generator
Ignition switch ON
11 to 14 V
E5-28 (VG) - E5-30 (E2G)
R-Y - R-W
Mass air flow meter
Idling, shift lever in P or N*2 or neutral*3, A/C switch off
0.5 to 3.0 V
E5-29 (THA) - E4-28 (E2)
R-L - BR
Intake air temperature sensor
Idling, Intake air temperature 20°C (68°F)
0.5 to 3.4 V
E4-32 (THW) - E4-28 (E2)
Y-B - BR
Engine coolant temperature sensor
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
E5-6 (#10) - E4-7 (E01)
E5-5 (#20) - E4-7 (E01)
E5-2 (#30) - E4-7 (E01)
E5-1 (#40) - E4-7 (E01)
R-L - W-B
B - W-B
R - W-B
G - W-B
Injector
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(See waveform 1)
E4-17 (IGT1) - E4-3 (E1)
E4-16 (IGT2) - E4-3 (E1)
E4-15 (IGT3) - E4-3 (E1)
E4-14 (IGT4) - E4-3 (E1)
P - BR
P-L - BR
LG - BR
LG-B - BR
Ignition coil
(ignition signal)
Idling
Pulse generation
(See waveform 2)
E4-23 (IGF1) - E4-3 (E1)
W-R - BR
Ignition coil
(ignition confirmation signal)
Ignition switch ON
4.5 to 5.0 V
Idling
Pulse generation
(See waveform 2)
E4-26 (G2) - E4-34 (NE-)
L - G
Camshaft position sensor
Idling
Pulse generation
(See waveform 3)
E4-27 (NE+) - E4-34 (NE-)
R - G
Crankshaft position sensor
Idling
Pulse generation
(See waveform 3)
E8-25 (FC) - E4-3 (E1)
L-B - BR
Fuel pump control
Ignition switch ON
11 to 14 V
Idling
Below 1.5 V
E4-5 (M+) - E5-3 (ME01)
P - W-B
Throttle actuator
Idling with warm engine
Pulse generation
(See waveform 4)
E4-4 (M-) - E5-3 (ME01)
L - W-B
Throttle actuator
Idling with warm engine
Pulse generation
(See waveform 5)
E4-21 (A1A+) - E4-3 (E1)
P - BR
Air fuel ratio sensor
Always (Ignition switch ON)
3.3 V*1
E4-31 (A1A-) - E4-3 (E1)
L - BR
Air fuel ratio sensor
Always (Ignition switch ON)
2.9 V*1
E4-25 (OX1B) - E4-28 (E2)
W - BR
Heated oxygen sensor
Engine speed maintained 2500 rpm for 2 minutes after warming up sensor
Pulse generation
(See waveform 6)
E4-1 (HA1A) - E5-7 (E04)
R - W-B
Air fuel ratio sensor heater
Idling
Pulse generation
(See waveform 7)
Ignition switch ON
11 to 14 V
E4-2 (HT1B) - E5-4 (E03)
G - W-B
Heated oxygen sensor heater
Idling
Below 3.0 V
Ignition switch ON
11 to 14 V
E4-29 (KNK1) - E4-30 (EKNK)
B - W
Knock sensor
Maintain engine speed 4000 rpm after warming up engine
Pulse generation
(See waveform 8)
E4-13 (OC1+) - E4-12 (OC1-)
L-W - W
Camshaft timing oil control valve
Idling
Pulse generation
(See waveform 9)
E5-23 (PRG) - E4-7 (E01)
Y - W-B
Purge VSV
Ignition switch ON
11 to 14 V
Idling, under purge control
Pulse generation
(See waveform 10)
E8-5 (VPMP) - E4-3 (E1)
V-W - BR
Vent valve
(built into canister pump module)
Ignition switch ON
11 to 14 V
E8-6 (MPMP) - E4-3 (E1)
G - BR
Leak detection pump
(built into canister pump module)
Leak detection pump OFF
0 to 3 V
Leak detection pump ON
11 to 14 V
E8-31 (PPMP) - E4-28 (E2)
GR - BR
Canister pressure sensor
(built into canister pump module)
Ignition switch ON
3 to 3.6 V
E8-12 (STA) - E4-3 (E1)
B-Y - BR
Starter signal
Shift lever in N*2, or neutral*3, ignition switch START
5.5 V or more
E7-4 (STP) - E4-3 (E1)
L - BR
Stop light switch
Brake pedal depressed
7.5 to 14 V
Brake pedal released
Below 1.5 V
E8-16 (ST1-) - E4-3 (E1)
V-W - BR
Stop light switch
Ignition switch ON, Brake pedal depressed
Below 1.5 V
Ignition switch ON, Brake pedal released
7.5 to 14 V
E7-30 (W) - E4-7 (E01)
BR - W-B
MIL
Idling
11 to 14 V
Ignition switch ON
Below 3.5 V
E8-15 (ELS) - E4-3 (E1)
G - BR
Electric load
Taillight switch ON
7.5 to 14 V
Taillight switch OFF
0 to 1.5 V
E7-20 (ELS2) - E4-3 (E1)
B-W - BR
Electric load
Vehicle stationary, Voltage inverter outputs more than 100 W
11 to 14 V
Vehicle stationary, Voltage inverter outputs 100 W or less
0 to 1.5 V
E7-1 (TACH) - E4-3 (E1)
B-W - BR
Engine speed
Idling
Pulse generation
(See waveform 11)
E7-8 (SPD) - E4-3 (E1)
V-W - BR
Speed signal from combination meter
Driving at 12 mph (20 km/h)
Pulse generation
(See waveform 12)
E7-17 (TC) - E4-3 (E1)
G - BR
Terminal TC of DLC 3
Ignition switch ON
11 to 14 V
E5-32 (PSW) - E4-3 (E1)
G-W - BR
Power steering oil pressure switch
While turning steering wheel
Below 1.5 V
E8-30 (NSW)*2 - E4-3 (E1)
V - BR
Park/Neutral switch signal
IG switch ON and shift lever in P or N
Below 1 V
IG switch ON and shift lever except P or N
11 to 14 V
E7-33 (CANH) - E4-3 (E1)
B - BR
Communication signal with other components
Ignition switch ON
Pulse generation
(See waveform 13)
E7-34 (CANL) - E4-3 (E1)
W - BR
Communication signal with other components
Ignition switch ON
Pulse generation
(See waveform 14)
E4-24 (AIRV) - E4-3 (E1)
R-W - BR
Air switching valve for secondary air injection system
Ignition switch ON
11 to 14 V
E4-11 (AIRP) - E4-3 (E1)
Y-R - BR
Air pump control
Ignition switch ON
11 to 14 V
E5-20 (AIDI) - E4-3 (E1)
G-R - BR
Diagnostic information signal for air injection system
Air injection system operates
Pulse generation
(See waveform 15)
E5-22 (AIP) - E4-28 (E2)
GR - BR
Secondary air injection system pressure signal
Ignition switch ON
4.5 to 5.0 V
  1. *1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.
  2. *2: For automatic transmission models.
  3. *3: For manual transmission models.

WAVEFORM 1
Fuel injector
A093279E35
ECM Terminal Name
Between #10 (to #40) and E01
Tester Range
20 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 2
A093278E48
  1. Igniter IGT signal (from ECM to igniter)

  2. Igniter IGF signal (from igniter to ECM)
    ECM Terminal Name
    (a) Between IGT (1 to 4) and E1
    (b) Between IGF1 and E1
    Tester Range
    2 V/DIV., 20 ms./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as the engine speed increases.


WAVEFORM 3
A063955E51
  1. Camshaft position sensor

  2. Crankshaft position sensor
    ECM Terminal Name
    (a) Between G2 and NE-
    (b) Between NE+ and NE-
    Tester Range
    5 V/DIV., 20 ms./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as the engine speed increases.


WAVEFORM 4
Throttle actuator positive terminal
A208000E16
ECM Terminal Name
Between M+ and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 5
Throttle actuator negative terminal
A245848E17
ECM Terminal Name
Between M- and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 6
Heated oxygen sensor
A088863E49
ECM Terminal Name
Between OX1B and E2
Tester Range
0.2 V/DIV., 200 ms./DIV.
Condition
Engine speed maintained 2500 rpm for 2 minutes after warming up sensor

HINT:
In the DATA LIST, item O2S B1S2 shows the ECM input values from the heated oxygen sensor.


WAVEFORM 7
Air fuel ratio sensor heater
A205412E02
ECM Terminal Name
Between HA1A and E04
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling with warm engine

HINT:
The wavelength varies in accordance with the engine operating condition.


WAVEFORM 8
Knock sensor
A085286E88
ECM Terminal Name
Between KNK1 and EKNK
Tester Range
1 V/DIV., 0.01 to 1 ms./DIV.
Condition
Engine speed maintained 4000 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as the engine speed increases.
  2. The waveforms and amplitudes displayed differ slightly depending on the vehicle.


WAVEFORM 9
Camshaft timing oil control valve
A093229E54
ECM Terminal Name
Between OC1+ and OC1-
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 10
Purge VSV
A093230E13
ECM Terminal Name
Between PRG and E01
Tester Range
5 V/DIV., 50 ms./DIV.
Condition
Idling

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 11
Engine speed signal
A093225E44
ECM Terminal Name
Between TACH and E1
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 12
Vehicle speed signal
A093224E34
ECM Terminal Name
Between SPD and E1
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Driving at 20 km/h (12 mph)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 13
CAN communication signal (reference)
A086154E58
ECM Terminal Name
Between CANH and E1
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Ignition switch ON

WAVEFORM 14
CAN communication signal (reference)
A086155E53
ECM Terminal Name
Between CANL and E1
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Ignition switch ON

WAVEFORM 15
Terminal DI of air injection control driver
A255990E02
ECM Terminal Name
Between AIDI and E1
Tester Range
5 V/DIV., 50 ms./DIV.
Condition
Performing Active Test using Techstream (air injection system)

HINT:
The wavelength changes when the air injection control driver detects malfunctions in the air injection system .