Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > FREEZE FRAME DATA

for Preparation Click here



DESCRIPTION
Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was running or stopped, the engine was warmed up or not, the air fuel ratio was LEAN or RICH, and other data from the time the malfunction occurred.
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the Techstream, five separate sets of freeze frame data, including the data values at the time when the DTC was stored, can be checked.
These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.
A159471E08

HINT:
If it is impossible to replicate the problem even though a DTC is detected, confirm the freeze frame data.

  1. 3 data sets before the DTC was stored
  2. 1 data set when the DTC was stored
  3. 1 data set after the DTC was stored

LIST OF FREEZE FRAME DATA

Techstream Display
Measurement Item
Diagnostic Note
Vehicle Speed
Vehicle speed
Speed indicated on speedometer
Engine Speed
Engine speed
-
Calculate Load
Calculated load by ECM
-
Vehicle Load
Vehicle load
Load percentage in terms of maximum intake air flow amount
MAF
Air flow rate from mass air flow meter
If value approximately 0.0 gm/sec:
  1. Mass air flow meter power source circuit open
  2. VG circuit open or short
If value 160.0 gm/sec or more:
  1. E2G circuit open
Atmosphere Pressure
Atmospheric pressure
-
Coolant Temp
Engine coolant temperature
  1. If value -40°C (-40°F): sensor circuit open
  2. If value higher than 135°C (275°F): sensor circuit shorted
Intake Air
Intake air temperature
  1. If value -40°C (-40°F): sensor circuit open
  2. If value higher than 128°C (262°F): sensor circuit shorted
Engine Run Time
Engine run time
-
Initial Engine Coolant Temp
Initial engine coolant temperature
Service data
Initial Intake Air Temp
Initial intake air temperature
Service data
Battery Voltage
Battery voltage
-
Accel Sens. No.1 Volt %
Accelerator pedal position No. 1
-
Accel Sens. No.2 Volt %
Accelerator pedal position No. 2
-
Throttle Sensor Volt %
Throttle valve opening percentage according to throttle position sensor
Value calculated based on the voltage at terminal VTA1
Throttl Sensor #2 Volt %
Throttle valve opening percentage according to throttle position sensor No. 2
Value calculated based on the voltage at terminal VTA2
Throttle Sensor Position
Throttle sensor positioning
Recognition value for throttle opening angle on ECM
Throttle Motor DUTY
Throttle actuator
ETCS service data
Throttle Position
Throttle valve opening angle
Reference:
When the engine stalls, is difficult to start, or idles roughly
ISC Flow
Flow rate calculated from information from each sensor
Reference:
When the engine stalls, is difficult to start, or idles roughly
ISC Position
Target valve opening angle calculated from ISC control
Reference:
When the engine stalls, is difficult to start, or idles roughly
ISC Feedback Value
ISC feedback value
Reference:
When the engine stalls, is difficult to start, or idles roughly
ISC Learning Value
ISC learning value
Reference:
When the engine stalls, is difficult to start, or idles roughly
Electric Load Feedback Val
Electrical load feedback value
Reference:
When the engine stalls, is difficult to start, or idles roughly
Air Conditioner FB Val
Air conditioner load feedback value
Reference:
When the engine stalls, is difficult to start, or idles roughly
PS Feedback Val
Power steering load feedback value
Reference:
When the engine stalls, is difficult to start, or idles roughly
Low Revolution Control
Status of low engine speed control
Reference:
When the engine stalls, is difficult to start, or idles roughly
N Range Status
Judgement for shift lever in N
Reference:
When the engine stalls, is difficult to start, or idles roughly
For automatic transmission models
Injector (Port)
Injection period of No. 1 cylinder
-
Injection Volum (Cylinder1)
Injection volume (Cylinder 1)
Quantity of fuel injection volume for 10 times
Fuel Pump/Speed Status
Fuel pump/speed status
Active Test support data
Vacuum Pump
Key-off EVAP system leak detection pump status
Active Test support data
EVAP (Purge) VSV
EVAP (Purge) VSV control duty
-
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
Purge Density Learn Value
Learning value of purge density
-
EVAP System Vent Valve
Key-off EVAP system vent valve status
-
EVAP Purge VSV
VSV status for EVAP control
-
Purge Cut VSV Duty
Purge cut VSV duty
-
Target Air Fuel Ratio
Ratio compared to stoichiometric level
-
AF Lambda B1S1
Fuel trim at air fuel ratio sensor
-
AFS Voltage B1S1
Air fuel ratio sensor output voltage for bank 1 sensor 1
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
AFS Current B1S1
Air fuel ratio sensor output current for bank 1 sensor 1
Value becomes higher when fuel-cut executed under high engine speed
A/F Heater Duty #1
Air fuel ratio heater duty ratio (for Bank 1)
-
O2S B1S2
Heated oxygen sensor output voltage for bank 1 sensor 2
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
O2S Impedance B1S2
Sub heated oxygen sensor impedance (bank 1 sensor 2)
-
O2 Heater B1S2
Heated oxygen sensor heater (for Bank 1 Sensor 2)
-
O2 Heater Curr Val B1S2
Heated oxygen sensor current (for Bank 1 Sensor 2)
-
Short FT #1
Short-term fuel trim of bank 1
Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
Long FT #1
Long-term fuel trim of bank 1
Overall fuel compensation carried out in long-term to compensate for continual deviation of short-term fuel trim from central value
Total FT #1
Total fuel trim valve for fuel system
-
Fuel System Status #1
Fuel system status (bank 1)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  2. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
  3. OLDrive: Open loop due to driving conditions (fuel enrichment)
  4. OLFault: Open loop due to detected system fault
  5. CLFault: Closed loop but air fuel ratio sensor, which is used for fuel control, is malfunctioning
Air pump pressure (absolute)
Air pump pressure
-
Air Pump Pulsation Pressure
Air pump pulsation damper
-
Secondary Air Control VSV
Secondary air injection system status
-
2nd Air System Status
Secondary system status
-
AI Test
Secondary air injection system operation prohibit
-
IGN Advance
Ignition timing advance for No. 1 cylinder
-
Knock Feedback Value
Feedback value of knocking
-
Knock Correct Learn Value
Correction learning value of knocking
-
Idle Spark Advn Ctrl #1
Ignition timing advance value (for No. 1 cylinder)
Reference:
When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #2
Ignition timing advance value (for No. 2 cylinder)
Reference:
When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #3
Ignition timing advance value (for No. 3 cylinder)
Reference:
When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #4
Ignition timing advance value (for No. 4 cylinder)
Reference:
When the engine stalls, is difficult to start, or idles roughly
Actual VVT Angle #1
Actual VVT displacement angle (bank 1)
-
VVT Control Status #1
VVT control (bank 1) status
-
VVT Advance Fail
Status of VVT advance fail
-
Catalyst Temp B1S1
Catalyst temperature (associated sensor 1)
-
Catalyst Temp B1S2
Catalyst temperature (associated sensor 2)
-
Starter Signal
Starter signal (STA terminal input status)
-
Power Steering Signal
Power steering signal
-
Neutral Position SW Signal
Park/neutral position switch status
For automatic transmission models
Clutch Switch
Clutch switch status
For manual transmission models
4WD SW
4WD switch status
For 4WD models
Transfer L4
Transfer L4 switch status
For 4WD models
For automatic transmission models
Stop Light Switch
Stop light switch status
-
A/C Signal
A/C switch status
-
Closed Throttle Position SW
Closed throttle position switch
-
Fuel Cut Condition
Fuel-cut condition
-
Immobiliser Communication
Immobiliser communication
OFF: Communication malfunctioning, or engine immobiliser system set
TC Terminal
TC terminal status
-
Time after DTC Cleared
Time since DTCs cleared
-
Distance from DTC Cleared
Distance traveled since DTCs cleared
-
Warmup Cycle Cleared DTC
Warm-up cycles since DTCs cleared
Number of warm-up cycles since DTCs cleared
Dist Batt Cable Disconnect
Distance after battery cable disconnected
-
IG OFF Elapsed Time
TC and CG (TE1) terminals of DLC3
-
TC and TE1
TC and TE1 terminals of DLC3
-
Ignition Trig. Count
Ignition counter to calculated misfire rate
-
Cylinder #1 Misfire Count
Misfire count of cylinder 1
-
Cylinder #2 Misfire Count
Misfire count of cylinder 2
-
Cylinder #3 Misfire Count
Misfire count of cylinder 3
-
Cylinder #4 Misfire Count
Misfire count of cylinder 4
-
All Cylinders Misfire Count
All cylinders misfire count
-
Misfire RPM
Average engine speed when misfire occurs
-
Misfire Load
Average engine load when misfire occurred
-
Misfire Margin
Margin to detect engine misfire
When the variation in the engine speed is large and exceeds the misfire detection threshold, the misfire count starts. Misfire margin is a measure of how much the engine speed variation can increase with respect to the threshold before the engine is determined to be misfiring. A large value means there is a large margin for the engine speed to vary before the engine is determined to be misfiring.
Catalyst OT MF F/C
Catalyst overheat misfire prevention fuel cut function availability
-
Cat OT MF F/C History
Catalyst overheat misfire prevention fuel cut function history
-
Cat OT MF F/C Cylinder#1
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#2
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#3
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#4
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)
-
Engine Speed (Starter Off)
Engine speed when starter off
Reference:
When the engine stalls, is difficult to start, or idles roughly
Starter Count
Number of times starter turned on after ignition switch turned from off to ON
Reference:
When the engine stalls, is difficult to start, or idles roughly
Run Dist of Previous Trip
Distance traveled during previous trip
Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.

HINT:
Run Dist of Previous Trip in the freeze frame data present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of the Data List (real-time measurements), or for freeze frame data present when DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.

Engine Starting Time
Engine run time (elapsed time from ignition switch ON to off)
Reference:
When the engine stalls, is difficult to start, or idles roughly
Previous Trip Coolant Temp
Coolant temperature of previous trip
Reference:
When the engine stalls, is difficult to start, or idles roughly
Previous Trip Intake Temp
Intake air coolant temperature of previous trip
Reference:
When the engine stalls, is difficult to start, or idles roughly
Engine Oil Temperature
Engine oil temperature (estimated)
Reference:
When the engine stalls, is difficult to start, or idles roughly
Previous Trip Eng Oil Temp
Engine oil temperature of previous trip (estimated)
Reference:
When the engine stalls, is difficult to start, or idles roughly
Ambient Temp for A/C
Ambient temperature
Reference:
When the engine stalls, is difficult to start, or idles roughly
Previous Trip Ambient Temp
Ambient temperature of previous trip
Reference:
When the engine stalls, is difficult to start, or idles roughly
Engine Start Hesitation
History of instances of slow engine starts
Reference:
When the engine stalls, is difficult to start, or idles roughly
Low Rev for Eng Start
History of low engine speed after engine starts
Reference:
When the engine stalls, is difficult to start, or idles roughly
Minimum Engine Speed
Minimum engine speed
Reference:
When the engine stalls, is difficult to start, or idles roughly
Fuel Cut Elps Time
Elapsed time since Fuel Cut due to high engine speed
The time elapsed after high engine rotation speed has occurred (More than the rpm at which fuel cut occurs +500 rpm).
ACT VSV
A/C cut status for Active Test
-
Brake Override System
Brake override system status
-
Idle Fuel Cut
Fuel cut idle
ON: When throttle valve fully closed and engine speed over 1500 rpm
FC TAU
Fuel cut TAU (Fuel cut during very light load)
Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete
Immobiliser Fuel Cut
Status of the immobiliser fuel cut
-
Immobiliser Fuel Cut History
Status of the immobiliser fuel cut history
-
Electrical Load Signal 1
Electrical load signal (ELS1 terminal input)
-
Electrical Load Signal 2
Electrical load signal (ELS2 terminal input)
-
SPD (SP2)
Output shaft speed
For automatic transmission models
Lock Up
ECT Lock Up status
For automatic transmission models