Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › REAR AIRBAG SENSOR (for Double Cab)

REAR AIRBAG SENSOR (for Double Cab) > INSTALLATION

for Preparation Click here


HINT:
Use the same procedures for the RH side and LH side.



1. INSTALL REAR AIRBAG SENSOR
  1. Check that the ignition switch is OFF.

  1. Check that the cable is disconnected from the battery negative (-) terminal.

    CAUTION:
    After disconnecting the cable from the terminal, wait for at least 90 seconds before starting the operation.

  1. Install the rear airbag sensor with the nut.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. Installation of the connector is done with the sensor assembly installed. Make sure the sensor assembly is installed to the specified torque.
    2. If the sensor assembly has been dropped, or there are cracks, dents or other defects in the case, bracket or connector, replace the sensor assembly with a new one.
    3. When installing the sensor assembly, make sure that the SRS wiring does not interfere with any other parts and is not pinched between other parts.
    4. After installation, shake the sensor assembly to check that it is not loose.



2. INSTALL REAR SEAT OUTER BELT ASSEMBLY LH


    B087300E03
  1. Check the amount of inclination required to lock the retractor.

    1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any directions. Also check that the belt locks when inclination of the retractor is 45° or more.

      NOTICE:
      Do not disassemble the retractor.

      If operation is not as specified, replace the rear seat outer belt.



    B087317E02
  1. Hook the lower stay of the retractor onto the 2 body hooks.

  1. Tighten bolt A, and then tighten bolt B.

    Torque:
    8.5 N*m{ 85 kgf*cm , 75 in.*lbf } (for bolt A)
    42 N*m{ 430 kgf*cm , 31 ft.*lbf } (for bolt B)



    B087316E01
  1. Install the shoulder anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. Check that the shoulder anchor rotates smoothly.



    B087330E02
  1. Install the floor anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

    NOTICE:
    1. Make sure that the rear seat outer belt is oriented in the correct direction when installing.
    2. Be careful not to place the rear seat outer belt over the convex areas of the floor panel.

  1. Check the ELR lock.

    NOTICE:
    1. The check should be performed with the rear seat outer belt installed.
    2. Do not allow the anchor part of the rear seat outer belt and the protruding parts of the floor panel to overlap.


    1. With the belt installed, check that the belt locks when it is pulled out quickly.
      If operation is not as specified, replace the rear seat outer belt.

  1. Remove the bolt and floor anchor.



3. INSTALL QUARTER INSIDE TRIM BOARD LH
  1. Engage the 2 clips and install the quarter inside trim board.

  1. Tighten the 3 screws.



    B087432E01
  1. Engage the claw and close the cover.



    B087330E04
  1. Install the floor anchor of the rear seat belt outer with the bolt.
    Text in Illustration 
    *a
    Convex

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

    NOTICE:
    1. Make sure that the rear seat outer belt is oriented in the correct direction when installing.
    2. Be careful not to place the rear seat outer belt over the convex areas of the floor panel.



4. INSTALL QUARTER TRIM LOWER PANEL LH
  1. Engage the 2 claws and 2 clips, and install the quarter trim lower panel.



5. INSTALL LUGGAGE COMPARTMENT SIDE TRAY
  1. w/ Woofer:

    1. Engage the 5 claws and 7 clips, and install the luggage compartment side tray.

    2. Tighten the bolt.

  1. w/o Woofer:

    1. Engage the 5 claws and 5 clips, and install the luggage compartment side tray.

    2. Tighten the 3 bolts.



6. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the rear door opening trim weatherstrip.



7. INSTALL REAR DOOR SCUFF PLATE LH
  1. Engage the 8 claws and install the rear door scuff plate.



8. INSTALL REAR SEAT BACK HINGE SUB-ASSEMBLY LH


    B087196E01
  1. Install the rear seat back hinge with the 2 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 14 ft.*lbf }



9. INSTALL REAR SEAT BACK ASSEMBLY LH


    B087195E01
  1. Install the rear seat back with the 2 bolts.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



10. INSTALL REAR SEAT BACK HINGE COVER


    B087211E01
  1. for LH Side:

    HINT:
    Follow the same procedures as for the opposite side.


    1. Engage the 3 claws and install the rear seat back hinge cover.

  1. for RH Side:

    1. Install the rear seat back hinge cover .



11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



12. INSPECT SRS WARNING LIGHT