Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › FRONT SEAT SIDE AIRBAG ASSEMBLY (for Separate Seat Type)

FRONT SEAT SIDE AIRBAG ASSEMBLY (for Separate Seat Type) > DISPOSAL

for Preparation Click here


HINT:
  1. When scrapping a vehicle equipped with the SRS or disposing of the front seat side airbag assembly, be sure to deploy the airbag in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the SERVICE DEPT. of TOYOTA MOTOR SALES, U.S.A., INC.
  2. When disposing of a front seat side airbag assembly with an airbag deployed in a collision, follow the procedure in step 1-(e) in DISPOSAL.


CAUTION:
  1. Never dispose of a front seat side airbag assembly which has an undeployed airbag.
  2. The airbag produces a loud exploding sound when it deploys, so perform the operation outdoors, where it will not create a nuisance to nearby residents.

  3. H040004E04
    When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool), perform the operation in a place away from electrical noise.
  4. When deploying an airbag, perform the operation at least 10 m (33 ft) away from the airbag assembly.
  5. The front seat side airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
  6. Use gloves and safety glasses when handling a front seat side airbag assembly with a deployed airbag.
  7. Always wash your hands with water after completing the operation.
  8. Do not apply water, etc. to a front seat side airbag assembly with the deployed airbag.



1. DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (WHEN SCRAPPING VEHICLE DEPLOYMENT METHOD)


H040005E02

HINT:
Have a battery as the power source to deploy the airbag.

  1. Check the function of SST (see step 1-(a) on page Click here).



    H041647
  1. Disconnect the front seat side airbag assembly connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



    H041648E01
  1. Set SST.

    1. Connect the connectors of 2 SSTs to the front seat side airbag assembly connector.

      SST
      09082-00700  
      09082-00750  

      NOTICE:
      To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock.



    2. H040007E09
    3. Move SST at least 10 m (33 ft) away from the front of the vehicle.

    4. Close all the doors and windows of the vehicle.

      NOTICE:
      Take care not to damage the SST wire harness.

    5. Connect the SST red clip to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

  1. Deploy the airbag.

    1. Check that no one is inside the vehicle or within a 10 m (33 ft) radius of the vehicle.

    2. Press the SST activation switch and deploy the airbag.

      HINT:
      The airbag deploys simultaneously when the LED of the SST activation switch lights up.

  1. Dispose of the front seat side airbag assembly.

    CAUTION:
    1. The front seat side airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
    2. Use gloves and safety glasses when handling a front seat side airbag assembly a the deployed airbag.
    3. Do not apply water, etc. to a front seat side airbag assembly with the deployed airbag.
    4. Always wash your hands with water after completing the operation.

    HINT:
    When scrapping a vehicle, deploy the airbag and scrap the vehicle with the front seat side airbag assembly installed.