FRONT PASSENGER AIRBAG ASSEMBLY > INSTALLATION |
| 1. INSTALL FRONT PASSENGER AIRBAG ASSEMBLY |
![]() |
Engage the 10 hooks so that the connector side faces the outside of the vehicle, and install the front passenger airbag assembly.
| 2. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY WITH PASSENGER AIRBAG ASSEMBLY |
Install the instrument panel sub-assembly with passenger airbag assembly with the 8 bolts and nut.
Engage the 5 clamps and connect the 4 connectors.
Remove the protective tape from the steering column cover upper and steering wheel sub-assembly.
| 3. CONNECT PASSENGER AIRBAG CONNECTOR |
![]() |
Connect the passenger airbag connector and clamp.
| 4. INSTALL INSTRUMENT SIDE PANEL RH |
![]() |
Engage the 3 claws and install the instrument side RH.
| 5. INSTALL LOWER INSTRUMENT COVER SUB-ASSEMBLY |
Connect the connectors.
Engage the 5 clips and install the instrument lower cover.
Install the bolt <B>.
| 6. INSTALL LOWER INSTRUMENT PANEL LH |
Install the lower instrument panel LH with the 3 bolts <B>.
| 7. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH |
Engage the 2 clips and install the instrument panel lower finish panel sub-assembly RH.
Install the bolt <B>.
| 8. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Pull the bottom of the stopper.
![]() |
Attach the stopper to the glove compartment door as shown in the illustration.
![]() |
Install the glove compartment door assembly with 3 hinges, holding it horizontal.
![]() |
Slightly deform the upper part of the glove compartment door assembly, and install the glove compartment door assembly.
| 9. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
Engage the 10 clips and install the instrument cluster center finish panel sub-assembly.
| 10. INSTALL COMBINATION METER ASSEMBLY |
Connect the 2 connectors.
Install the combination meter assembly with the 4 screws <E>.
| 11. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
Engage the 10 clips and install the instrument cluster center finish panel sub-assembly.
| 12. INSTALL NO. 1 LOWER INSTRUMENT PANEL FINISH PANEL |
Connect the connectors.
Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.
Install the 2 bolts <B>.
| 13. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Connect the hood lock control cable assembly.
![]() |
Engage the 2 claws and install the hood lock control lever sub-assembly.
| 14. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET |
Connect all the connectors.
Connect the plug.
Engage the 5 clips and install the radio receiver assembly with bracket.
Install the 4 bolts.
| 15. INSTALL AIR CONDITIONING CONTROL ASSEMBLY |
![]() |
Connect the 2 connectors.
Engage the 4 clips and install the air conditioning control assembly.
| 16. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Bench Seat Type) |
Engage the 2 clips and claw, and install the front console box.
Install the clip and 2 bolts <A>.
![]() |
Install the 2 instrument panel cup holders.
Install the box bottom mat.
Install the shift knob.
| 17. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Bench Seat Type) |
Engage the 2 clips and claw, and install the front console box.
Install the clip and 2 bolts <A>.
![]() |
Install the 2 instrument panel cup holders.
Install the box bottom mat.
Install the shift knob.
| 18. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Separate Seat Type) |
![]() |
Engage the 2 clips and claw, and install the front console box.
Install the 2 screws <F>.
Install the shift knob.
| 19. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Separate Seat Type) |
Engage the 2 clips and claw, and install the front console box.
Install the 2 screws <F>.
| 20. INSTALL INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type) |
Engage the 2 clips and 4 claws, and install the instrument panel cup holder tray.
Install the 2 instrument panel cup holders.
| 21. INSTALL REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type) |
![]() |
Engage the 4 claws and install the console box rear.
Install the 2 screws <F> and 2 bolts <B>.
Install the console box carpet.
| 22. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type) |
Engage the 4 clips and claw, and install the console upper panel sub-assembly.
| 23. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type) |
![]() |
Engage the 6 clips and claw, and install the console upper rear panel.
Install the shift knob.
| 24. INSTALL INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake) |
Engage the 4 clips and install the instrument panel hole cover.
| 25. INSTALL INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake) |
Engage the 4 clips and 2 claws, and install the instrument panel under tray.
| 26. INSTALL FRONT PILLAR GARNISH LH (for Regular Cab) |
for LH Side:
Install the 3 wire harness clamps.
Engage the claw and clip, and install the front pillar garnish.
Tighten the 2 screws.
![]() |
Engage the 2 claws and install the assist grip plug.
| 27. INSTALL FRONT PILLAR GARNISH LH (for Access Cab) |
for LH Side:
Install the 3 wire harness clamps.
Engage the claw and clip, and install the front pillar garnish and assist grip.
Tighten the 2 screws.
![]() |
Engage the 2 claws and install the assist grip plug.
| 28. INSTALL FRONT PILLAR GARNISH LH (for Double Cab) |
Install the 3 wire harness clamps (LH side only).
Engage the claw and clip, and install the front pillar garnish.
Tighten the 2 screws.
![]() |
Engage the 2 claws and install the assist grip plug.
| 29. INSTALL FRONT PILLAR GARNISH RH (for Regular Cab) |
| 30. INSTALL FRONT PILLAR GARNISH RH (for Access Cab) |
| 31. INSTALL FRONT PILLAR GARNISH RH (for Double Cab) |
| 32. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Regular Cab) |
Install the front door opening trim weatherstrip.
| 33. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Access Cab) |
Install the front door opening trim weatherstrip.
| 34. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Double Cab) |
Install the front door opening trim weatherstrip.
| 35. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Regular Cab) |
| 36. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Access Cab) |
| 37. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Double Cab) |
| 38. INSTALL COWL SIDE TRIM BOARD LH (for Regular Cab) |
Engage the 2 clips and install the cowl side trim board.
Install the clip.
| 39. INSTALL COWL SIDE TRIM BOARD LH (for Access Cab) |
Engage the 2 clips and install the cowl side trim board.
Install the clip.
| 40. INSTALL COWL SIDE TRIM BOARD LH (for Double Cab) |
Engage the 2 clips and install the cowl side trim board.
Install the clip.
| 41. INSTALL COWL SIDE TRIM BOARD RH (for Regular Cab) |
| 42. INSTALL COWL SIDE TRIM BOARD RH (for Access Cab) |
| 43. INSTALL COWL SIDE TRIM BOARD RH (for Double Cab) |
| 44. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab) |
Engage the 8 claws and clip, and install the front door scuff plate.
| 45. INSTALL FRONT DOOR SCUFF PLATE LH (for Access Cab) |
Engage the 9 claws and clip, and install the front door scuff plate.
| 46. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab) |
Engage the 9 claws and install the front door scuff plate.
| 47. INSTALL FRONT DOOR SCUFF PLATE RH (for Regular Cab) |
| 48. INSTALL FRONT DOOR SCUFF PLATE RH (for Access Cab) |
| 49. INSTALL FRONT DOOR SCUFF PLATE RH (for Double Cab) |
| 50. INSTALL FRONT FLOOR FOOTREST |
![]() |
Engage the 2 clips and install the front floor footrest.
| 51. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 52. INSPECT SRS WARNING LIGHT |