Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › KNOCK SENSOR

KNOCK SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL KNOCK CONTROL SENSOR


A087061E01
  1. Install the knock control sensor with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Make sure that the knock sensor is at the correct angle when installing.

  1. Connect the knock control sensor connector.



2. INSTALL INTAKE MANIFOLD


G037711E01
  1. Install a new gasket onto the intake manifold.

  1. Install the intake manifold with the 5 bolts and 2 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



    G037710E01
  1. Connect the engine wire harness to the relay block.

  1. Install the nut shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 3 connectors.



    G037709E01
  1. Install the harness clamp bracket with the bolt.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Engage the wire harness clamp.

  1. Connect the compressor magnetic clutch connector. (w/ AIR CONDITIONING)

  1. Engage the engine wire harness clamp.

  1. Connect the VSV connector.



    G039455E01
  1. Connect the ventilation hose No. 3.



    G039454E01
  1. Connect the water by-pass hose No. 2.



    G037706E01
  1. Install the clamp bracket with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



    G037705E01
  1. Connect the vacuum hose.



    G037704E01
  1. Connect the fuel vapor feed hose to the VSV.



3. CONNECT FUEL HOSE


G037903E01
  1. Align the fuel hose connector with the pipe stem, and insert the fuel hose until the retainer makes a "click" sound.

  1. Push down the checker of the fuel hose.

    NOTICE:
    1. Check that there are no scratches or foreign objects around the disconnected parts of the fuel hose connector and pipe before performing this work.
    1. After connecting the fuel hose, check that the fuel hose is securely connected by pulling the fuel hose connector and pipe.

  1. Push the fuel hose down until the checker of the fuel hose makes a "click" sound.



4. CONNECT NO. 2 FUEL HOSE


G037904E01
  1. Align the fuel hose connector with the pipe stem, and insert the fuel hose until the retainer makes a "click" sound.

  1. Push down the checker of the fuel hose.

    NOTICE:
    1. Check that there are no scratches or foreign objects around the disconnected parts of the fuel hose connector and pipe before performing this work.
    1. After connecting the fuel hose, check that the fuel hose is securely connected by pulling the fuel hose connector and pipe.

  1. Push the fuel hose down until the checker of the fuel hose makes a "click" sound.



5. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY


    G037700E01
  1. Install a new gasket onto the intake manifold.



    G037699E01
  1. Install the throttle with motor body with the 2 bolts and 2 nuts.

    Torque:
    9 N*m{ 92 kgf*cm , 80 in.*lbf }



    G037698E01
  1. Connect the water by-pass hose.

  1. Connect the water by-pass hose No. 2.

  1. Connect the throttle motor connector.



6. INSTALL INTAKE AIR CONNECTOR


    G037697E01
  1. Install the intake air connector with the 3 bolts.

    Torque:
    8 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Tighten the 2 hose clamp bolts.

    Torque:
    5 N*m{ 51 kgf*cm , 44 in.*lbf }



    G037696E01
  1. Connect the vacuum hose.



    G037695E01
  1. Connect the ventilation hose No. 2.



    G037694E01
  1. Connect the vacuum hose.

  1. Engage the wire harness clamp.

  1. Connect the pressure sensor connector.



7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



8. ADD ENGINE COOLANT
  1. Tighten the engine drain plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain plug.

  1. Disconnect the 2 vinyl hoses.

  1. Slowly fill the system with engine coolant.

    Capacity:
    M/T: 8.7 liters (9.2 US qts, 7.7 lmp. qts)
    A/T: 8.6 liters (9.1 US qts, 7.6 lmp. qts)

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids.)
    3. New Toyota vehicles are filled with Toyota Super Long Life Coolant. When replacing the coolant, Toyota Super Long Life Coolant (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)) is recommended.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Check the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.

  1. Install the radiator cap securely.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

    Item
    Condition
    Fan speed
    Any setting except OFF
    Temperature
    Toward warm
    Air condition switch
    OFF

  1. Squeeze the inlet and outlet radiator hoses several times by hand while warning up the engine.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, perform the steps from (d) through (k) and repeat the operation until the coolant level remains at the full level.

  1. Check the coolant level inside the radiator reservoir tank again. If it is below the full level, add coolant.

  1. Install the engine under cover No. 1 with the 4 bolts. (PRE RUNNER AND 4WD TYPE)

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



9. CHECK FOR ENGINE COOLANT LEAKAGE


G038195E01

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Fluid and steam could be blown out under pressure.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Pump it up to 118 kPa (1.2 kgf/cm2, 17.1 psi) and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hose, radiator and water pump for leakage. If no external leakage is found, check the heater core, cylinder block and cylinder head.



10. CHECK FOR FUEL LEAKAGE


11. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY NO.1 (for 4WD and Pre-Runner)