Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > Key Lock-in Prevention Function does not Work Properly

for Preparation Click here


DESCRIPTION

To prevent the key from being locked in the vehicle, the multiplex network body ECU prevents the doors from being locked by monitoring 2 switches: 1) the unlock warning switch, which turns ON when the key is inserted into the ignition key cylinder; and 2) the driver side courtesy light switch, which turns ON when the driver side door is opened.

WIRING DIAGRAM


B124997E03


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK - BODY GROUND)


    B063404E02
  1. Disconnect the 1K driver side J/B connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Connection
    Specified Condition
    1K-10 (KSW) - Body ground
    No key in ignition key cylinder
    10 kΩ or higher
    1K-10 (KSW) - Body ground
    Key inserted in ignition key cylinder
    Below 1 Ω

  1. Reconnect the driver side J/B connector.



OK
Go to step 4
NG


2.INSPECT UNLOCK WARNING SWITCH ASSEMBLY


    I044492E01
  1. Remove the unlock warning switch.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Switch Connection
    Specified Condition
    1 - 2
    Not pushed
    10 kΩ or higher
    1 - 2
    Pushed
    Below 1 Ω

  1. Reinstall the unlock warning switch.



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY
OK


3.CHECK HARNESS AND CONNECTOR (SWITCH ASSEMBLY - DRIVER SIDE J/B ASSEMBLY AND BODY GROUND)


    I044490E02
  1. Disconnect the U1 unlock warning switch connector.

  1. Disconnect the 1K driver side J/B connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard:
    Tester Connection
    Specified Condition
    U1-1 - 1K-10 (KSW)
    Below 1 Ω
    U1-2 - Body ground
    Below 1 Ω

  1. Reconnect the unlock warning switch connector.

  1. Reconnect the driver side J/B connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (DRIVER SIDE)
  1. Move the room light switch to the DOOR position and open the driver side door. Check that the room light turns ON.

    OK:
    Room light turns ON.



OK
REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY
NG


5.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (DRIVER SIDE)


    B087741E02
  1. Remove the front door courtesy light switch assembly.

  1. Measure the resistance of the switch.

    Standard:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Not pushed (ON)
    Below 1 Ω
    1 - Body ground
    Pushed (OFF)
    10 kΩ or higher

  1. Reinstall the front door courtesy light switch assembly.



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY
OK


6.CHECK HARNESS AND CONNECTOR (SWITCH ASSEMBLY (DRIVER SIDE) - DRIVER SIDE J/B ASSEMBLY)


    I044491E02
  1. Disconnect the D11 front door courtesy light switch connector.

  1. Disconnect the 1F driver side J/B connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Specified Condition
    D11-1 - 1F-7 (DCTY)
    Below 1 Ω

  1. Reconnect the front door courtesy light switch connector.

  1. Reconnect the driver side J/B connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DRIVER SIDE JUNCTION BLOCK