Home › TRANSMISSION · A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0756    Shift Solenoid "B" Performance (Shift Solenoid Valve S2)

for Preparation Click here


DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).

DTC No.
DTC Detection Condition
Trouble Area
P0756
The gear required by the ECM does not match the actual gear when driving (2-trip detection logic)
  1. Shift solenoid valve S2 remains open or closed
  2. Shift solenoid valve SLT remains open or closed
  3. Valve body is blocked
  4. Automatic transmission (clutch, brake or gear, etc.)

MONITOR DESCRIPTION

This DTC indicates "stuck ON malfunction" or "stuck OFF malfunction" of the shift solenoid valve S2.
The ECM commands gear shifts by turning the shift solenoid valves "ON/OFF". When the gear position commanded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0756:
Shift solenoid valve S2/OFF malfunction
Shift solenoid valve S2/ON malfunction
Required sensors/Components (Main)
Shift solenoid valve S2
Required sensors/Components (Related)
Vehicle speed sensor, Throttle position sensor, Speed sensor (NT), Speed sensor (NO)
Frequency of operation
Continuous
Duration
OFF malfunction (A), (B) and (C): 0.4 seconds
OFF malfunction (D): Immediate
ON malfunction (A) and (B): 0.4 seconds
ON malfunction (C): 3 seconds
ON malfunction (D): 0.5 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
P0717 (Turbine speed sensor circuit)
P0722 (Output speed sensor circuit)
P0973, P0974 (Shift solenoid valve S1 circuit)
P0976, P0977 (Shift solenoid valve S2 circuit)
P0985, P0986 (Shift solenoid valve SR circuit)
P0985, P0986 (Shift solenoid valve SR circuit)
P0985, P0986 (Shift solenoid valve SR circuit)
P0748 (Shift solenoid valve SL1 circuit)
P0778 (Shift solenoid valve SL2 circuit)
P0128 (ECT (Engine coolant temperature) sensor circuit)
P0327, P0328, P0332, P0333 (KCS sensor circuit)
ETCS (Electric throttle control system)
Not system down
Transmission range
"D"
Duration time from shifting "N" to "D"
4 seconds or more
ECT
40°C (104°F) or more
Spark advance from Max. retard timing by KCS control
0° CA or more
Engine
Starting

OFF Malfunction (A) 
ECM selected gear
1st
Vehicle speed
2 to 40 km/h (1.2 to 24.9 mph)
Throttle valve opening angle
8% or more (When actual gear is 4th)
6.5% or more at 2000 rpm (Varies with engine speed)

OFF Malfunction (B) 
ECM selected gear
2nd
Vehicle speed
2 km/h (1.2 mph) or more
Output speed
2nd → 1st down-shift point or more
Throttle valve opening angle
6.5% or more at 2000 rpm (Varies with engine speed)

OFF Malfunction (C) 
Current ECM selected gear
5th
Last ECM selected gear
4th
Continuous time of ECM selecting 4th gear
2 seconds or more
Actual gear when ECM selected 4th gear
4th

OFF Malfunction (D) 
Current ECM selected gear
5th
Last ECM selected gear
4th

ON Malfunction (A) 
ECM selected gear
1st
Vehicle speed
2 to 40 km/h (1.2 to 24.9 mph)
Throttle valve opening angle
8% or more (When actual gear is 4th)
6.5% or more at 2000 rpm (Varies with engine speed)

ON Malfunction (B) 
ECM selected gear
4th
Vehicle speed
2 km/h (1.2 mph) or more
Throttle valve opening angle
6.5% or more at 2000 rpm (Varies with engine speed)

ON Malfunction (C) 
Current ECM selected gear
5th
Last ECM selected gear
4th
Vehicle speed (During transition from 4th to 5th gear)
Less than 100 km/h (62.2 mph)

ON Malfunction (D) 
ECM selected gear
5th
Engine speed - Turbine speed (NE - NT)
(After transition from 4th to 5th gear)
150 rpm or less
Vehicle speed (After transition from 4th to 5th gear)
Less than 100 km/h (62.2 mph)

TYPICAL MALFUNCTION THRESHOLDS

[OFF Malfunction]
  1. All of the following conditions are met: OFF malfunction (A), (B), (C) and (D)
    2 detections are necessary per driving cycle
    1st detection: temporary flag ON
    2nd detection: pending fault code ON

    OFF Malfunction (A) and (B) 
    Turbine speed/Output speed
    3.30 to 7.50

    OFF Malfunction (C) 
    Turbine speed/Output speed
    0.65 to 0.79

    OFF Malfunction (D) 
    Output record from ECM for 4th → 5th up-shift
    Recorded
[ON Malfunction]
  1. Both of the following conditions are met: ON malfunction (A) or (B), and ON malfunction (C) or (D)

    ON Malfunction (A) 
    Turbine speed/Output speed
    1.91 to 2.35

    ON Malfunction (B) 
    Turbine speed/Output speed
    1.28 to 1.53

    ON Malfunction (C) 
    Turbine speed - Output speed x 4th gear ratio
    (NT - NO x 4th gear ratio)
    1000 rpm or more

    ON Malfunction (D) 
    Turbine speed - Output speed x 5th gear ratio
    (NT - NO x 5th gear ratio)
    1000 rpm or more

INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. Follow the instructions on the Techstream and perform the Active Test.

    HINT:
    While driving, the shift position can be forcibly changed with the Techstream.
    Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (Click here).


    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operate shift solenoid valve and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of shift solenoid valves
    [Vehicle Condition]
    50 km/h (31 mph) or less

    HINT:
    1. This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
    2. The 4th to 5th up-shift must be performed with the accelerator pedal released.
    3. The 5th to 4th down-shift must be performed with the accelerator pedal released.
    4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
    5. The shift position commanded by the ECM is shown in the Data List display on the Techstream.
    6. The shift solenoid valve S1 turns ON/OFF normally with the shift lever is in D:

      ECM gear shift command
      1st
      2nd
      3rd
      4th
      5th
      Shift solenoid valve S2
      OFF
      ON
      ON
      OFF
      OFF

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0756)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P0756 is output
    A
    P0756 and other DTCs are output
    B

    HINT:
    If any other codes besides P0756 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)
G020657E01

NOTICE:
  1. Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).
  2. Be careful to prevent SST's hose from interfering with the exhaust pipe.
  3. Perform the test with the A/C OFF.

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Turn the ignition switch off.

  1. Lift the vehicle up.

  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Lower the vehicle.

  1. Fully apply the parking brake and chock the 4 wheels.

  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure when the engine is idling.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. Follow the instructions on the tester and perform the Active Test.

  1. Measure the line pressure with SST.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLT)*
    Operate the shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling

    HINT:
    *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.

    OK:
    The line pressure changes as specified when performing the Active Test.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


3.INSPECT SHIFT SOLENOID VALVE S2


    A110987E14
  1. Remove the shift solenoid valve S2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid S2 connector - Shift solenoid S2 body
    20°C (68°F)
    11 to 15 Ω

  1. Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE S2
OK


4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

    OK:
    There are no foreign objects on any valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)