DTC P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2714 | ECM detects a malfunction on SLT (ON side) according to the revolution difference of the turbine and the output shaft, and also by the oil pressure. (2-trip detection logic) |
|
| Related DTCs | P2714: Shift solenoid valve SLT/ON malfunction |
| Required sensors/Components | Shift solenoid valve SLT, Valve body, ATF temperature sensor, Speed sensor (NT), Speed sensor (SP2) |
| Frequency of operation | Continuous |
| Duration | Immediate |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0717 (Turbine speed sensor circuit) P0722 (Output speed sensor circuit) P0712, P0713, P2742, P2743 (TFT temperature sensor circuit) P0973, P0974 (Shift solenoid valve S1 circuit) P0976, P0977 (Shift solenoid valve S2 circuit) P0985, P0986 (Shift solenoid valve SR circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P2716 (Shift solenoid valve SLT circuit) P0128 (ECT (Engine coolant temperature) sensor circuit) P0327, P0328, P0332, P0333 (KCS sensor circuit) |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission range | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT | 40°C (104°F) or more |
| Spark advance from Max. retard timing by KCS control | 0° CA or more |
| Engine | Starting |
| ATF temperature | 10°C (50°F) or more |
| Summation of C1 clutch heat generations | Specified value |
| Shift solenoid valve S1 ON malfunction | Detected |
| Shift solenoid valve S2 ON malfunction | Detected |
| Shift solenoid valve SR OFF malfunction | Detected |
| 1-2 shift valve malfunction | Detected |
| Shift solenoid valve SL1 OFF malfunction | Detected |
| Shift solenoid valve SL2 ON malfunction | Detected |
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTCS P2714) |
Connect Techstream to the DLC3.
Turn the ignition switch to ON
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using Techstream.
| Result | Proceed to |
| Only P2714 are output | A |
| P2714 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT) |
![]() |
Turn the ignition switch off.
Lift the vehicle up.
Remove the test plug on the transmission case center right side and connect SST.
Lower the vehicle.
Fully apply the parking brake and chock the 4 wheels.
Connect Techstream to the DLC3.
Start the engine and warm it up.
Measure the line pressure when the engine is idling.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Follow the instructions on the Techstream and perform the Active Test.
Measure the line pressure with SST.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLT)* | Operate the shift solenoid SLT and raise line pressure | ON or OFF
| [Vehicle Condition]
|
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING TECHSTREAM (RUNNING TEST) |
Connect Techstream to the DLC3.
Clear the DTC (Click here).
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test using Techstream.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operate shift solenoid valve and set each shift position |
| Possible to check operation of shift solenoid valves [Vehicle Condition] 50 km/h (31 mph) or less |
Compare the ECM gear shift command and the actual gear position.
| ECM Gear Shift Command | 1st | 2nd | 3rd | 4th | 5th | Proceed to | ||
| Actual gear position under malfunction | Shift solenoid S1 | Stuck ON | 1st | 2nd | 2nd | 1st | N*1 | A |
| Stuck OFF | 4th | 3rd | 3rd | 4th | 5th | |||
| Shift solenoid S2 | Stuck ON*2 | 2nd | 2nd | 3rd | 3rd | N*1 | B | |
| Stuck OFF*3 | 1st | 1st | 4th | 4th | 5th | |||
| Shift solenoid SL2 | Stuck ON | 1st | 2nd | 3rd | 4th | N*1 | C | |
| Stuck OFF | 1st | 2nd | 3rd | 4th | 5th | |||
| Shift solenoid SR | Stuck ON*4 | 1st | 2nd | 3rd | 4th | 5th | D | |
| Stuck OFF*5 | 1st | 2nd | 3rd | 4th | 4th | |||
| Actual gear position when normal | 1st | 2nd | 3rd | 4th | 5th | E | ||
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 4.INSPECT SHIFT SOLENOID VALVE S1 |
![]() |
Remove the shift solenoid valve S1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Shift solenoid S1 connector - Shift solenoid S1 body | 20°C (68°F) | 11 to 15 Ω |
Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | ||
| ||
| 5.INSPECT SHIFT SOLENOID VALVE S2 |
![]() |
Remove the shift solenoid valve S2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Shift solenoid S2 connector - Shift solenoid S2 body | 20°C (68°F) | 11 to 15 Ω |
Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | ||
| ||
| 6.INSPECT SHIFT SOLENOID VALVE SL2 |
![]() |
Remove the shift solenoid valve SL2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | ||
| ||
| 7.INSPECT SHIFT SOLENOID VALVE SR |
![]() |
Remove the shift solenoid valve SR.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Shift solenoid SR connector - Shift solenoid SR body | 20°C (68°F) | 11 to 15 Ω |
Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.
|
| ||||
| OK | |
| 8.INSPECT SHIFT SOLENOID VALVE SL1 |
![]() |
Remove the shift solenoid valve SL1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | ||
| ||
| 9.INSPECT SHIFT SOLENOID VALVE SLT |
![]() |
Remove the shift solenoid valve SLT.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.
|
| ||||
| OK | |
| 10.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | |
| 11.INSPECT TORQUE CONVERTER ASSEMBLY |
Check the torque converter assembly .
|
| ||||
| OK | ||
| ||