Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Driver Side Power Window does not Operate with Power Window Master Switch

for Preparation Click here


DESCRIPTION

If the driver side manual UP / DOWN and AUTO DOWN function does not operate, a malfunction may exist in the power window regulator motor assembly LH (driver side), power window regulator master switch assembly or wire harness.

WIRING DIAGRAM


B264212E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (DRIVER SIDE)
  1. Remove the power window regulator motor assembly LH (driver side).

  1. Apply battery voltage to connector terminals 1 and 2.



    B290924E01
  1. Check that the motor smoothly rotates.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 2.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise

    Text in Illustration 
    *1
    Motor Gear
    *a
    Clockwise
    *b
    Counterclockwise
    *c
    Component without harness connected
    (Power Window Regulator Motor Assembly LH)



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (DRIVER SIDE)
OK


2.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - P/W RELAY AND BODY GROUND)
B293230E01
  1. Disconnect the P9*1 or P18*2 power window regulator master switch assembly connector.

    1. *1: for Double Cab
    2. *2: for Access Cab

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for Double Cab 
    Tester Connection
    Switch Condition
    Specified Condition
    P9-6 - Body ground
    Ignition switch ON
    11 to 14 V
    for Access Cab 
    Tester Connection
    Switch Condition
    Specified Condition
    P18-15 - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Double Cab 
    Tester Connection
    Condition
    Specified Condition
    P9-1 - Body ground
    Always
    Below 1 Ω
    for Access Cab 
    Tester Connection
    Condition
    Specified Condition
    P18-7 - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *A
    for Double Cab
    *B
    for Access Cab
    *a
    Front view of wire harness connector
    (to Power Window Regulator Master Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
  1. Disconnect the P9*1 or P18*2 power window regulator master switch assembly connector.

    1. *1: for Double Cab
    2. *2: for Access Cab

  1. Disconnect the P10 power window regulator motor assembly LH (driver side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Double Cab 
    Tester Connection
    Condition
    Specified Condition
    P9-3 - P10-2
    Always
    Below 1 Ω
    P9-4 - P10-1
    Always
    Below 1 Ω
    P9-3 - Body ground
    Always
    10 kΩ or higher
    P9-4 - Body ground
    Always
    10 kΩ or higher
    for Access Cab 
    Tester Connection
    Condition
    Specified Condition
    P18-10 - P10-2
    Always
    Below 1 Ω
    P18-12 - P10-1
    Always
    Below 1 Ω
    P18-10 - Body ground
    Always
    10 kΩ or higher
    P18-12 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY