Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM (for Bench Seat Type)

OCCUPANT CLASSIFICATION SYSTEM (for Bench Seat Type) > DIAGNOSIS SYSTEM

for Preparation Click here



CHECK DLC3


    A004550E20
  1. The vehicle's ECU uses the ISO 9141-2 for communication protocol. The terminal arrangement of the DLC3 complies with SAE J1962 and matches the ISO 15765-4 format.

    Symbols (Terminal No.)
    Terminal Description
    Condition
    Specified Condition
    SIL (7) - SG (5)
    Bus + line
    During transmission
    Pulse generation
    CG (4) - Body ground
    Chassis ground
    Always
    Below 1 Ω
    BAT (16) - Body ground
    Battery positive
    Always
    11 to 14 V

    HINT:
    If the display shows a communication error message when the Techstream is connected to the DLC3, the ignition switch is turned to ON and the Techstream is operated, there is a problem on the vehicle side or tool side.
    1. If communication is normal when the tool is connected to another vehicle, inspect the DLC3 on the original vehicle.
    2. If communication is still not possible when the tool is connected to another vehicle, the problem is probably in the tool itself. Consult the Service Department listed in the tool's instruction manual.


SYMPTOM SIMULATION

HINT:
The most difficult case in troubleshooting is when no symptoms occur. In such cases, a thorough customer problem analysis must be carried out. Then the same or similar conditions and environment in which the problem occurred in the customer's vehicle should be simulated. Regardless of the technician's experience or skill, if troubleshooting proceeds without confirmation of the problem symptoms, something important is likely to be overlooked and incorrect assumptions may be made at some points in the repair operation.
This leads to a standstill in troubleshooting.



    D025083E06
  1. Vibration method (When vibration seems to be the major cause)

    HINT:
    Perform the simulation method only during the primary check period (for approximately 6 seconds after the ignition switch is turned to ON).


    1. Slightly vibrate the part of the sensor considered to be the cause of the problem with your fingers and check whether the malfunction occurs.

      HINT:
      Shaking the relays too strongly may result in open relays.

    2. Slightly shake the connector vertically and horizontally.

    3. Slightly shake the wire harness vertically and horizontally.
      The connector joint and fulcrum of the vibration are the main areas that should be checked thoroughly.


FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR
  1. Initial check

    1. Turn the ignition switch to ON.

    2. The passenger airbag ON/OFF indicator illuminates ON and OFF for approximately 4 seconds, and then turns them off for approximately 2 seconds.

    3. Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator indicates ON or OFF depending on the conditions listed below.

      Front Seat Passenger
      ON Indicator
      OFF Indicator
      SRS Warning Light
      Adult seated
      ON
      OFF
      OFF
      Child seated / Child restrain system set
      OFF
      ON
      OFF
      Vacant
      OFF
      OFF
      OFF
      Passenger occupant classification system failure
      OFF
      ON
      ON

      HINT:

      1. The passenger airbag ON/OFF indicator operates based on the timing chart below in order to check the indicator light circuit.


        H100194E01

      2. When the occupant classification system malfunctions, the SRS warning light comes on and the passenger airbag ON/OFF indicator indicates OFF. In this case, check the DTCs in the airbag system first.


PASSENGER AIRBAG ON/OFF INDICATOR CHECK


    H046083
  1. Turn the ignition switch to ON.

  2. Check that the passenger airbag ON/OFF indicator illuminates ON and OFF for approximately 4 seconds, and then turns them off for approximately 2 seconds.

    HINT:
    Refer to the table in the previous step regarding the passenger airbag ON/OFF indicator when approximately 6 seconds have elapsed after the ignition switch is turned to ON.