POWER WINDOW CONTROL SYSTEM > Rear Power Window RH does not Operate with Rear Power Window Switch RH |

| 1.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH |
Remove the rear power window regulator switch assembly RH.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (U) - 3 (B) 4 (SD) - 5 (D) | UP | Below 1 Ω |
| 2 (SU) - 1 (U) 4 (SD) - 5 (D) | OFF | Below 1 Ω |
| 2 (SU) - 1 (U) 3 (B) - 5 (D) | DOWN | Below 1 Ω |
| *a | Component without harness connected (Power Window Regulator Switch Assembly RH) |
|
| ||||
| OK | |
| 2.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH |
Remove the rear power window regulator motor assembly RH.
Apply battery voltage to connector terminals 1 and 2.
![]() |
Check that the motor smoothly rotates.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 2 Battery negative (-) → 1 | Motor gear rotates clockwise |
| Battery positive (+) → 1 Battery negative (-) → 2 | Motor gear rotates counterclockwise |
| *1 | Motor Gear |
| *a | Clockwise |
| *b | Counterclockwise |
| *c | Component without harness connected (Rear Power Window Regulator Motor Assembly) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - P/W RELAY) |
![]() |
Disconnect the P16 rear power window regulator switch assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P16-3 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Rear Power Window Regulator Switch Assembly RH) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) |
Disconnect the P16 rear power window regulator switch assembly RH connector.
Disconnect the P13 rear power window regulator motor assembly RH connector.
Measure the resistance according the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P16-1 (U) - P13-2 | Always | Below 1 Ω |
| P16-5 (D) - P13-1 | Always | Below 1 Ω |
| P16-1 (U) - Body ground | Always | 10 kΩ or higher |
| P16-5 (D) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY) |
Disconnect the P16 rear power window regulator switch assembly RH connector.
Disconnect the P9 power window regulator master switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P16-2 (SU) - P9-10 | Always | Below 1 Ω |
| P16-4 (SD) - P9-18 | Always | Below 1 Ω |
| P16-2 (SU) - Body ground | Always | 10 kΩ or higher |
| P16-4 (SD) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||