Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

If the front passenger side manual UP / DOWN function does not operate, a malfunction may exist in the power window regulator motor assembly RH (front passenger side), power window regulator switch assembly (front passenger side), power window regulator master switch assembly or wire harness.

WIRING DIAGRAM


B290898E04


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FRONT PASSENGER SIDE)
  1. Remove the power window regulator switch assembly RH (front passenger side).



    B293342E01
  1. Measure the resistance according to the value(s) in the table below

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4(U) - 3(B)
    2(SD) - 1(D)
    UP
    Below 1 Ω
    5(SU) - 4(U)
    2(SD) - 1(D)
    OFF
    Below 1 Ω
    5(SU) - 4(U)
    3(B) - 1(D)
    DOWN
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Switch Assembly RH (Front Passenger Side))



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (FRONT PASSENGER SIDE)
OK


2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FRONT PASSENGER SIDE)
  1. Remove the Power Window Regulator Motor Assembly RH (front passenger side).

  1. Apply battery voltage to connector terminals 1 and 2.



    B290925E01
  1. Check that the motor smoothly rotates.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 2.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise

    Text in Illustration 
    *1
    Motor Gear
    *a
    Clockwise
    *b
    Counterclockwise
    *c
    Component without harness connected
    (Power Window Regulator Motor Assembly RH)



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FRONT PASSENGER SIDE)
OK


3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - P/W RELAY)
B290899E04
  1. Disconnect the P14 power window regulator switch assembly (front passenger side) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    P14-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Window Regulator Switch Assembly (Front Passenger Side))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)
  1. Disconnect the P14 power window regulator switch assembly (front passenger side) connector.

  1. Disconnect the P11 power window regulator motor assembly RH (front passenger side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P14-4 (U) - P11-2
    Always
    Below 1 Ω
    P14-1 (D) - P11-1
    Always
    Below 1 Ω
    P14-4 (U) - Body ground
    Always
    10 kΩ or higher
    P14-1 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
  1. Disconnect the P14 power window regulator switch assembly (front passenger side) connector.

  1. Disconnect the P9*1 or P18*2 power window regulator master switch assembly connector.

    1. *1: for Double Cab
    2. *2: for Access Cab

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Double Cab 
    Tester Connection
    Condition
    Specified Condition
    P14-5 (SU) - P9-16
    Always
    Below 1 Ω
    P14-2 (SD) - P9-15
    Always
    Below 1 Ω
    P14-5 (SU) - Body ground
    Always
    10 kΩ or higher
    P14-2 (SD) - Body ground
    Always
    10 kΩ or higher
    for Access Cab 
    Tester Connection
    Condition
    Specified Condition
    P14-5 (SU) - P18-16
    Always
    Below 1 Ω
    P14-2 (SD) - P18-18
    Always
    Below 1 Ω
    P14-5 (SU) - Body ground
    Always
    10 kΩ or higher
    P14-2 (SD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY