POWER WINDOW CONTROL SYSTEM > Rear Power Window LH does not Operate with Rear Power Window Switch LH |

| 1.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH |
Remove the rear power window regulator switch assembly LH.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (U) - 3 (B) 4 (SD) - 5 (D) | UP | Below 1 Ω |
| 2 (SU) - 1 (U) 4 (SD) - 5 (D) | OFF | Below 1 Ω |
| 2 (SU) - 1 (U) 3 (B) - 5 (D) | DOWN | Below 1 Ω |
| *a | Component without harness connected (Power Window Regulator Switch Assembly LH) |
|
| ||||
| OK | |
| 2.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
Remove the rear power window regulator motor assembly LH.
Apply battery voltage to connector terminals 1 and 2.
![]() |
Check that the motor smoothly rotates.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 2 Battery negative (-) → 1 | Motor gear rotates clockwise |
| Battery positive (+) → 1 Battery negative (-) → 2 | Motor gear rotates counterclockwise |
| *1 | Motor Gear |
| *a | Clockwise |
| *b | Counterclockwise |
| *c | Component without harness connected (Rear Power Window Regulator Motor Assembly LH) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - P/W RELAY) |
![]() |
Disconnect the P15 rear power window regulator switch assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P15-3 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Rear Power Window Regulator Switch Assembly LH) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH) |
Disconnect the P15 rear power window regulator switch assembly LH connector.
Disconnect the P12 rear power window regulator motor assembly LH connector.
Measure the resistance according the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P15-1 (U) - P12-2 | Always | Below 1 Ω |
| P15-5 (D) - P12-1 | Always | Below 1 Ω |
| P15-1 (U) - Body ground | Always | 10 kΩ or higher |
| P15-5 (D) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY) |
Disconnect the P15 rear power window regulator switch assembly LH connector.
Disconnect the P9 power window regulator master switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P15-2 (SU) - P9-12 | Always | Below 1 Ω |
| P15-4 (SD) - P9-13 | Always | Below 1 Ω |
| P15-2 (SU) - Body ground | Always | 10 kΩ or higher |
| P15-4 (SD) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||