Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Speaker Circuit

for Preparation Click here


DESCRIPTION

If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.
If a short is detected in a speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM


E233346E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - SPEAKER)
  1. Disconnect the S24 and S31 stereo component amplifier assembly connectors.

  1. Disconnect the S15 and S16 front No. 1 speaker assembly connectors.

  1. Disconnect the S19 and S20 front No. 2 speaker assembly connectors.

  1. Disconnect the S17 and S18 rear speaker assembly connectors.

  1. Disconnect the S21 No. 1 speaker assembly with box connector.

  1. Measure the resistance between the front No. 1 speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S24-2 (FL+) - S15-1
    Always
    Below 1 Ω
    S24-1 (FL-) - S15-2
    Always
    Below 1 Ω
    S24-9 (FR+) - S16-1
    Always
    Below 1 Ω
    S24-3 (FR-) - S16-2
    Always
    Below 1 Ω

  1. Measure the resistance between the front No. 2 speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S31-8 (TWL+) - S19-4 (+)
    Always
    Below 1 Ω
    S31-7 (TWL-) - S19-3 (-)
    Always
    Below 1 Ω
    S31-2 (TWR+) - S20-4 (+)
    Always
    Below 1 Ω
    S31-6 (TWR-) - S20-4 (-)
    Always
    Below 1 Ω

  1. Measure the resistance between the rear speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S31-3 (RL+) - S17-1
    Always
    Below 1 Ω
    S31-9 (RL-) - S17-2
    Always
    Below 1 Ω
    S31-10 (RR+) - S18-1
    Always
    Below 1 Ω
    S31-4 (RR-) - S18-2
    Always
    Below 1 Ω

  1. Measure the resistance between the No. 1 speaker assembly with box and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S24-5 (WFL+) - S21-2 (WF+)
    Always
    Below 1 Ω
    S24-12 (WFL-) - S21-4 (WF-)
    Always
    Below 1 Ω
    S24-4 (WFR+) - S21-1 (WF+)
    Always
    Below 1 Ω
    S24-10 (WFR-) - S21-3 (WF-)
    Always
    Below 1 Ω

  1. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S24-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    S24-1 (FL-) - Body ground
    Always
    10 kΩ or higher
    S24-9 (FR+) - Body ground
    Always
    10 kΩ or higher
    S24-3 (FR-) - Body ground
    Always
    10 kΩ or higher
    S31-8 (TWL+) - Body ground
    Always
    10 kΩ or higher
    S31-7 (TWL-) - Body ground
    Always
    10 kΩ or higher
    S31-2 (TWR+) - Body ground
    Always
    10 kΩ or higher
    S31-6 (TWR-) - Body ground
    Always
    10 kΩ or higher
    S31-3 (RL+) - Body ground
    Always
    10 kΩ or higher
    S31-9 (RL-) - Body ground
    Always
    10 kΩ or higher
    S31-10 (RR+) - Body ground
    Always
    10 kΩ or higher
    S31-4 (RR-) - Body ground
    Always
    10 kΩ or higher
    S24-5 (WFL+) - Body ground
    Always
    10 kΩ or higher
    S24-12 (WFL-) - Body ground
    Always
    10 kΩ or higher
    S24-4 (WFR+) - Body ground
    Always
    10 kΩ or higher
    S24-10 (WFR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E232748E02
  1. Disconnect the S15 and S16 front No. 1 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.4 to 2.2 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E233347E01
  1. Disconnect the S19 and S20 front No. 2 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (+) - 3 (-)
    Always
    1.5 to 2.5 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4.INSPECT REAR SPEAKER ASSEMBLY


    E232748E02
  1. Disconnect the S17 and S18 rear speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


5.INSPECT NO. 1 SPEAKER ASSEMBLY WITH BOX


    E233348E01
  1. Disconnect the S21 No. 1 speaker assembly with connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (WF+) - 3 (WF-)
    Always
    1.6 to 2.4 Ω
    2 (WF+) - 4 (WF-)
    Always
    1.6 to 2.4 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (No. 1 Speaker Assembly with Box)



NG
REPLACE NO. 1 SPEAKER ASSEMBLY WITH BOX (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)