Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM (w/o Navigation System)

REAR VIEW MONITOR SYSTEM (w/o Navigation System) > TERMINALS OF ECU



REAR TELEVISION CAMERA ASSEMBLY

E233219E01

  1. Disconnect the T19 television camera assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T19-3 (CGND) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω
    T19-4 (CB+) - Body ground
    B - Body ground
    Power source
    Ignition switch ON, shift lever in R
    5.5 to 7.05 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the rear television camera assembly connector.

  4. Measure the waveform according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T19-2 (CV+) - T19-1 (CV-)
    R - W
    Video signal
    Ignition switch ON, shift lever in R
    Pulse generation
    (See waveform 1)
    Ignition switch ON, shift lever in R, screen blacked out by covering camera lens
    Pulse generation
    (See waveform 2)

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the inner rear view mirror assembly with the connector connected.

    If the result is not as specified, the rear television camera assembly may have a malfunction.



  5. E171712E28
  6. Using an oscilloscope, check the waveform.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the inner rear view assembly with the connector connected.


    1. Waveform 1 (Reference)
      Item
      Content
      Terminal No. (Symbol)
      T19-2 (CV+) - T19-1 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

    2. Waveform 2 (Reference)
      Item
      Content
      Terminal No. (Symbol)
      T19-2 (CV+) - T19-1 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Ignition switch ON, shift lever in R, screen blacked out by covering camera lens

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

      Text in Illustration 
      *a
      Waveform 1
      *b
      Waveform 2
      *c
      Synchronized Signal
      *d
      Video Waveform


INNER REAR VIEW MIRROR ASSEMBLY

E236284E01

  1. Disconnect the I8 inner rear view mirror assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I8-1 (IG) - I8-2 (E)
    LG - W-B
    Power source (IG)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    I8-2 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    I8-8 (+B) - I8-2 (E)
    R - W-B
    Power source (+B)
    Always
    11 to 14 V

  3. Reconnect the inner rear view mirror assembly connector.

  4. Measure the voltage and waveform according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I8-3 (REV) - I8-2 (E)
    R - W-B
    Reverse signal
    Ignition switch ON, shift lever not in R
    Below 1 V
    Ignition switch ON, shift lever in R
    11 to 14 V
    I8-6 (CV-) - I8-2 (E)
    W - W-B
    Ground
    Always
    Below 1 V
    I8-7 (CV+) - I8-6 (CV-)
    R - W
    Video signal
    Ignition switch ON, shift lever in R
    Pulse generation
    (See waveform 1)
    Ignition switch ON, shift lever in R, screen blacked out by covering camera lens
    Pulse generation
    (See waveform 2)
    I8-13 (CGND) - Body ground
    Shield - Body ground
    Shield ground
    Always
    Below 1 V
    I8-14 (CB+) - I8-2 (E)
    B - W-B
    Power source
    Ignition switch ON, shift lever in R
    5.5 to 7.05 V



  5. E171712E28
  6. Using an oscilloscope, check the waveform.

    1. Waveform 1 (Reference)
      Item
      Content
      Terminal No. (Symbol)
      I8-7 (CV+) - I8-6 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

    2. Waveform 2 (Reference)
      Item
      Content
      Terminal No. (Symbol)
      I8-7 (CV+) - I8-6 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Ignition switch ON, shift lever in R, screen blacked out by covering camera lens

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

      Text in Illustration 
      *a
      Waveform 1
      *b
      Waveform 2
      *c
      Synchronized Signal
      *d
      Video Waveform