STEERING COLUMN ASSEMBLY > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 4. REMOVE NO.2 LOWER STEERING WHEEL COVER |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the steering wheel cover lower No. 2.
| 5. REMOVE NO.3 LOWER STEERING WHEEL COVER |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the No. 3 lower steering wheel cover.
| 6. REMOVE STEERING PAD |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Using T30 "TORX" socket wrench, loosen the 2 bolts completely.
Pull the steering pad toward rear.
![]() |
Using a screwdriver with its tip wrapped with protective tape, release the 2 airbag connector locks.
Disconnect the 2 airbag connectors.
| *1 | Protective Tape |
| *2 | Locking button |
![]() |
Disconnect the horn terminal to remove the steering pad.
| 7. REMOVE STEERING WHEEL ASSEMBLY |
![]() |
Remove the steering wheel assembly set nut.
Place matchmarks on the steering wheel assembly and main shaft assembly.
Using SST, remove the steering wheel assembly.
| 8. REMOVE LOWER STEERING COLUMN COVER |
![]() |
Remove the 2 screws.
Disengage the 2 claws to remove the lower steering column cover.
| 9. REMOVE UPPER STEERING COLUMN COVER |
![]() |
Disengage the claw and then remove the upper steering column cover.
| 10. REMOVE SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Disconnect the airbag connector and the connector from the spiral cable sub-assembly.
Disengage the 3 claws and remove the spiral cable sub-assembly.
| 11. REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY |
![]() |
Disconnect the 2 connectors.
Using a screwdriver wrapped with protective tape, disengage the claw and remove the windshield wiper switch assembly.
| 12. REMOVE FRONT FLOOR FOOTREST |
![]() |
Disengage the 2 clips and remove the front floor footrest.
| 13. REMOVE FRONT DOOR SCUFF PLATE LH (for Regular Cab) |
![]() |
Disengage the 8 claws and clip, and remove the front door scuff plate.
| 14. REMOVE FRONT DOOR SCUFF PLATE LH (for Access Cab) |
![]() |
Disengage the 9 claws and clip, and remove the front door scuff plate.
| 15. REMOVE FRONT DOOR SCUFF PLATE LH (for Double Cab) |
![]() |
Disengage the 9 claws and remove the front door scuff plate.
| 16. REMOVE COWL SIDE TRIM BOARD LH (for Regular Cab) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim board.
| 17. REMOVE COWL SIDE TRIM BOARD LH (for Access Cab) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim board.
| 18. REMOVE COWL SIDE TRIM BOARD LH (for Double Cab) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim board.
| 19. REMOVE INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake) |
![]() |
Disengage the 4 clips and 2 claws, and remove the instrument panel under tray.
| 20. REMOVE INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake) |
![]() |
Disengage the 4 clips and remove the instrument panel hole cover.
| 21. REMOVE INSTRUMENT PANEL LOWER LH |
![]() |
Remove the 3 bolts <B> and the lower instrument panel LH.
| 22. REMOVE INSTRUMENT PANEL COVER SUB-ASSEMBLY LOWER |
![]() |
Remove the bolt <B>.
Disengage the 5 clips and remove the instrument lower cover sub-assembly.
Disconnect the connectors.
| 23. REMOVE STEERING COLUMN HOLE COVER |
![]() |
Disengage the 4 clips and remove the steering column hole cover.
| 24. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY |
Remove the No. 1 engine under cover sub-assembly with the 4 bolts.
| 25. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT |
![]() |
Mark matchmarks on the power steering gear assembly and No. 2 steering intermediate shaft.
Remove bolt C and No. 2 steering intermediate shaft from the power steering gear assembly.
| 26. REMOVE STEERING SLIDING YOKE |
Mark matchmarks on the steering sliding yoke, steering intermediate shaft sub-assembly No. 2 and steering intermediate shaft assembly.
Remove bolts A and B from the steering sliding yoke.
Slide the steering sliding yoke up and separate it from the steering intermediate shaft sub-assembly No. 2.
Pull down the steering sliding yoke from the steering intermediate shaft assembly to remove.
| 27. REMOVE STEERING COLUMN ASSEMBLY |
![]() |
Disconnect the connectors and wire harness clamps.
Remove the bolt and 2 nuts, then remove the steering column assembly from the instrument panel reinforcement assembly.