DTC B1820/55 Short in Front Driver Side - Side Squib Circuit |
DTC B1821/55 Open in Front Driver Side - Side Squib Circuit |
DTC B1822/55 Short to GND in Front Driver Side - Side Squib Circuit |
DTC B1823/55 Short to B+ in Front Driver Side - Side Squib Circuit |
| DTC No. | DTC Detecting Conditions | Trouble Areas |
| B1820/55 |
|
|
| B1821/55 |
|
|
| B1822/55 |
|
|
| B1823/55 |
|
|

| 1.CHECK DTC |
Proceed to the appropriate step according to DTC readings.
If using the Techstream (read the 5-digit DTCs):
Using the Techstream, check for DTCs (Click here).
| Result | Proceed to |
| DTC B1820 is output. | A |
| DTC B1821 is output. | B |
| DTC B1822 is output. | C |
| DTC B1823 is output. | D |
If not using the Techstream (read the 2-digit DTCs): Check for DTCs (Click here).
| Result | Proceed to |
| DTC 55 is output. | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK NO. 2 FLOOR WIRE (FOR SHORT) |
![]() |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S26-1 (SFD+) - S26-2 (SFD-) | Always | 1 MΩ or Higher |
|
| ||||
| NG | ||
| ||
| 3.CHECK NO. 2 FLOOR WIRE (FOR OPEN) |
![]() |
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S26-1 (SFD+) - S26-2 (SFD-) | Always | Below 1 Ω |
|
| ||||
| NG | ||
| ||
| 4.CHECK NO. 2 FLOOR WIRE (TO GROUND) |
![]() |
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S26-1 (SFD+) - Body ground | Always | 1 MΩ or Higher |
| S26-2 (SFD-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| NG | ||
| ||
| 5.CHECK NO. 2 FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| S26-1 (SFD+) - Body ground | Ignition switch ON | Below 1 V |
| S26-2 (SFD-) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| NG | ||
| ||
| 6.CHECK NO. 2 FLOOR WIRE (SIDE SQUIB (DRIVER SEAT SIDE) CIRCUIT) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| S26-1 (SFD+) - Body ground | Ignition switch ON | Below 1 V |
| S26-2 (SFD-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S26-1 (SFD+) - S26-2 (SFD-) | Always | Below 1 Ω |
| S26-1 (SFD+) - Body ground | Always | 1 MΩ or Higher |
| S26-2 (SFD-) - Body ground | Always | 1 MΩ or Higher |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S26-1 (SFD+) - S26-2 (SFD-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 7.REPLACE FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY LH (SIDE SQUIB (DRIVER SEAT SIDE)) |
![]() |
Replace the front seat with adjuster frame assembly LH (Click here).
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 8.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| NG | ||
| ||
| 9.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Connect the connectors to the center airbag sensor assembly.
Using a service wire, connect S26-1 (SFD+) and S26-2 (SFD-) of connector C.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | |
| 10.CHECK FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY LH |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the service wire from connector C.
Connect the connector to the front seat with adjuster frame assembly LH.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||