DTC B1825/56 Short in Front Passenger Side - Side Squib Circuit |
DTC B1826/56 Open in Front Passenger Side - Side Squib Circuit |
DTC B1827/56 Short to GND in Front Passenger Side - Side Squib Circuit |
DTC B1828/56 Short to B+ in Front Passenger Side - Side Squib Circuit |
| DTC No. | DTC Detecting Conditions | Trouble Areas |
| B1825/56 |
|
|
| B11826/56 |
|
|
| B1827/56 |
|
|
| B1828/56 |
|
|

| 1.CHECK DTC |
Proceed to the appropriate step according to DTC readings.
If using the Techstream (read the 5-digit DTCs):
Using the Techstream, check for DTCs (Click here).
| Result | Proceed to |
| DTC B1825 is output. | A |
| DTC B1826 is output. | B |
| DTC B1827 is output. | C |
| DTC B1828 is output. | D |
If not using the Techstream (read the 2-digit DTCs):
Check for DTCs (Click here).
| Result | Proceed to |
| DTC 56 is output. | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK FLOOR WIRE (FOR SHORT) |
![]() |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S27-1 (SFP+) - S27-2 (SFP-) | Always | 1 MΩ or Higher |
|
| ||||
| NG | ||
| ||
| 3.CHECK FLOOR WIRE (FOR OPEN) |
![]() |
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S27-1 (SFP+) - S27-2 (SFP-) | Always | Below 1 Ω |
|
| ||||
| NG | ||
| ||
| 4.CHECK FLOOR WIRE (TO GROUND) |
![]() |
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S27-1 (SFP+) - Body ground | Always | 1 MΩ or Higher |
| S27-2 (SFP-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| NG | ||
| ||
| 5.CHECK FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| S27-1 (SFP+) - Body ground | Ignition switch ON | Below 1 V |
| S27-2 (SFP-) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| NG | ||
| ||
| 6.CHECK FLOOR WIRE (SIDE SQUIB (FRONT PASSENGER SEAT SIDE) CIRCUIT) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| S27-1 (SFP+) - Body ground | Ignition switch ON | Below 1 V |
| S27-2 (SFP-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S27-1 (SFP+) - S27-2 (SFP-) | Always | Below 1 Ω |
| S27-1 (SFP+) - Body ground | Always | 1 MΩ or Higher |
| S27-2 (SFP-) - Body ground | Always | 1 MΩ or Higher |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S27-1 (SFP+) - S27-2 (SFP-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 7.REPLACE FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY RH (SIDE SQUIB (FRONT PASSENGER SEAT SIDE)) |
![]() |
Replace the front seat with adjuster frame assembly RH (Click here).
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 8.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| NG | ||
| ||
| 9.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Turn ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Connect the connectors to the center airbag sensor assembly.
Using a service wire, connect S27-1 (SFP+) and S27-2 (SFP-) of connector C.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | |
| 10.CHECK FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY LH |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the service wire from connector C.
Connect the connector to the front seat with adjuster frame assembly RH.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||