Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Separate Seat Type Driver Side)

FRONT SEAT ASSEMBLY (for Separate Seat Type Driver Side) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL SEAT POSITION SENSOR


    B076909E05
  1. Temporarily install the seat position sensor.

  1. Install a 1 mm (0.04 in.) feeler gauge between the slide rail and seat position sensor as shown in the illustration.

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, make sure that the SRS wiring does not interfere with other parts and is not pinched between other parts.

    HINT:
    Make sure that the clearance between the seat position sensor and seat rail is within 0.6 to 2 mm (0.023 to 0.079 in.).

  1. Push the top of the seat position sensor. While holding the seat position sensor, tighten the seat position sensor using a "TORX" socket wrench T30.

    Torque:
    8.0 N*m{ 80 kgf*cm , 71 in.*lbf }



2. INSTALL RECLINING ADJUSTER OUTSIDE COVER LH


    B087384E01
  1. Install the reclining adjuster outside cover with the screw.



3. INSTALL RECLINING ADJUSTER OUTSIDE COVER RH

HINT:
Follow the same procedures as for the reclining adjuster outside cover LH.



4. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    B087383E01
  1. Engage the claw and install the reclining adjuster inside cover.

  1. Tighten the screw.



5. INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:
Follow the same procedures as for the reclining adjuster inside cover LH.



6. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY


    B203911E01
  1. Hook the 12 hooks.

  1. Install the lumbar support adjuster with the 2 screws.

  1. Install 2 new wiring harness clamps.

  1. Cut each wiring harness clamp 5 to 10 mm (0.197 to 0.394 in.) from the stopper, as shown in the illustration.



7. INSTALL FRONT SEAT CUSHION COVER


    B113810E02
  1. Using hog ring pliers, install the front seat cushion cover with new hog rings.

    NOTICE:
    1. Do not soil or scratch the front seat cushion cover.
    2. When installing the hog rings, minimize wrinkles as far as possible.



    B121724E01
  1. Engage the 3 hooks and 2 claws, and install the front seat cushion pad together with the front seat cushion cover.

  1. Using hog ring pliers, install new hog rings.

  1. Hook the front seat cushion cover to the front seat frame adjuster.



8. INSTALL LOWER ACTIVE HEADREST UNIT


    B205929
  1. Install the lower active headrest unit with the 2 nuts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



9. INSTALL UPPER ACTIVE HEADREST UNIT


    B205928E01
  1. Connect the lower active headrest unit cable.

  1. Install the upper active headrest with the 5 nuts.

    Torque:
    Nut A:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    Torque:
    Nut B:
    14 N*m{ 142 kgf*cm , 10 ft.*lbf }



10. INSTALL FRONT SEAT BACK COVER


    B121725E01
  1. Install the front seat back pad onto the front seat frame adjuster.

  1. Using hog ring pliers, install the front seat back cover with new hog rings.

    NOTICE:
    1. Do not soil or scratch the front seat back cover.
    2. When installing the hog rings, minimize wrinkles as far as possible.

  1. Attach straps and tighten the nut.

    Torque:
    5.5 N*m{ 55 kgf*cm , 49 in.*lbf }

    CAUTION:
    1. For vehicles with side air bag, the front seat back cover must be securely installed. Otherwise, the side air bag may not deploy properly.
    2. Make sure that the strap is not twisted after installing the inner hook.
    3. Install the inner hook securely.

  1. Roll the front seat back cover down and install the 2 wires.

  1. Using hog ring pliers, install new hog rings.



11. INSTALL FRONT SEAT HEADREST SUPPORT


    B087398E01
  1. Engage the 2 claws and install the front seat headrest support.

    HINT:
    Follow the same procedures as for the opposite side.



    B121726E01
  1. Using hog ring pliers, install the new hog rings.

  1. Install the wire harness clamp and connector clamp.



12. INSTALL FRONT SEAT CUSHION INNER SHIELD


    B087379E01
  1. Engage the claw and clip, and install the front seat cushion inner shield.

  1. Tighten the screw.



13. INSTALL FRONT SEAT INNER BELT ASSEMBLY


    B087333E02
  1. Install the front seat inner belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Be careful not to place the front seat inner belt over the convex areas of the front seat with adjuster frame.

  1. Check that the front seat inner belt rotates smoothly.

  1. Connect the seat position airbag sensor connector.

  1. Install the 2 wire harness clamps and 2 connector clamps.



14. INSTALL FRONT SEAT CUSHION SHIELD


    B087378E01
  1. Engage the 2 claws and clip, and install the front seat cushion shield.

  1. Tighten the screw.



15. INSTALL RECLINING ADJUSTER RELEASE HANDLE


    B087388E01
  1. Engage the claw and install the reclining adjuster release handle.



16. INSTALL LUMBAR ADJUSTER DIAL


    B087376E01
  1. Line up the lumbar adjuster dial and push in it to engage it.



17. INSTALL FRONT SEAT HEADREST ASSEMBLY


    B087393E02
  1. Disengage the lock button of the front seat headrest support and install the front seat headrest.