Home › BODY › INTERIOR › ROOF HEADLINING (for Regular Cab)

ROOF HEADLINING (for Regular Cab) > INSTALLATION

for Preparation Click here



1. INSTALL ROOF WIRE


    B087489E03
  1. Install the roof wire with 5 new adhesive tapes, as shown in the illustration.
    Text in Illustration 
    *a
    Groove



2. INSTALL ROOF HEADLINING PAD


    B087490E03
  1. Install a new roof headlining pad onto the roof headlining, as shown in the illustration.
    Text in Illustration 
    *a
    Groove



3. INSTALL ROOF HEADLINING ASSEMBLY


    B087491E01
  1. Install the roof headlining into the vehicle.

  1. Install the wire harness clamps.

  1. Connect the 3 roof wire connectors.



4. INSTALL COAT HOOK

HINT:
Follow the same procedures as for the opposite side.



    B087466E02
  1. Turn the coat hook 90° clockwise and install it.



5. INSTALL VISOR HOLDER

HINT:
Follow the same procedures as for the opposite side.



    B087467E02
  1. Turn the visor holder 90° clockwise and install it.



6. INSTALL VISOR ASSEMBLY LH
  1. Install the visor into the visor holder.

  1. Install the 2 screws.



7. INSTALL VISOR ASSEMBLY RH

HINT:
Follow the same procedures as for the visor assembly LH.



8. INSTALL ASSIST GRIP PLUG

HINT:
Follow the same procedures as for the opposite side.

  1. Engage the claw and install the assist grip plug.

  1. Tighten the screw.



    B087594E01
  1. Engage the 2 claws and close the cover.



9. INSTALL ROOM LIGHT ASSEMBLY


    B087468E01
  1. Connect the room light connector.

  1. Engage the 3 claws and install the room light.



    B087469E01
  1. Engage the 2 claws and install the room light lens.



10. INSTALL QUARTER INSIDE TRIM BOARD LH
  1. Engage the 2 clips and install the quarter trim board.

  1. Tighten the 3 screws.



    B087492E01
  1. Engage the claw and close the cover.



    B087330E04
  1. for LH Side and Separate Seat Type RH Side:
    Text in Illustration 
    *a
    Convex

    1. Install the floor anchor of the front seat outer belt with the bolt.

      Torque:
      42 N*m{ 430 kgf*cm , 31 ft.*lbf }

      NOTICE:
      1. Make sure that the floor anchor of the front seat outer belt is oriented in the correct direction when installing.
      2. Be careful not to place the floor anchor of the front seat outer belt over the convex areas of the floor panel.



    B290464E01
  1. for Bench Seat Type RH Side:
    Text in Illustration 
    *a
    Convex

    1. Install the wiring harness clamp.

    2. Connect the belt tension sensor connector.

    3. Install the floor anchor of the front seat outer belt with the bolt.

      Torque:
      42 N*m{ 430 kgf*cm , 31 ft.*lbf }

      NOTICE:
      1. Make sure that the floor anchor of the front seat outer belt is oriented in the correct direction when installing.
      2. Be careful not to place the floor anchor of the front seat outer belt over the convex areas of the floor panel.



11. INSTALL QUARTER INSIDE TRIM BOARD RH

HINT:
Follow the same procedures as for the quarter inside trim board LH.



12. INSTALL QUARTER TRIM LOWER PANEL LH
  1. Engage the 2 claws and 3 clips, and install the quarter trim lower panel.



13. INSTALL QUARTER TRIM LOWER PANEL RH

HINT:
Follow the same procedures as for the quarter trim lower panel LH.



14. INSTALL BACK PANEL TRIM (for Separate Seat Type)
  1. Install the back panel trim with the 4 clips.



15. INSTALL BACK PANEL TRIM COVER (for Separate Seat Type)
  1. Engage the 4 claws and install the back panel trim cover.

  1. Install the 2 clips.



16. INSTALL JACK ASSEMBLY (for Separate Seat Type)


17. INSTALL BACK PANEL UPPER GARNISH
  1. Engage the 4 claws and 5 clips, and install the back panel upper garnish.



18. INSTALL BACK PANEL TRIM COVER
  1. for Separate Seat Type and Bench Seat Type:

    1. Engage the 6 claws and install the back panel trim cover.

      HINT:
      Follow the same procedures as for the opposite side (for Bench Seat Type).

  1. for Bench Seat Type:

    1. Engage the 6 claws and install the back panel trim cover.



19. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
  1. Install the instrument panel sub-assembly with passenger airbag assembly with the 8 bolts and nut.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf } for bolt <C>

  1. Engage the 5 clamps and connect the 4 connectors.

  1. Remove the protective tape from the steering column cover upper and steering wheel sub-assembly.



20. CONNECT PASSENGER AIRBAG CONNECTOR


21. INSTALL INSTRUMENT SIDE PANEL


    B085791E01
  1. Engage the 3 claws and install the instrument side RH.



22. INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY
  1. Connect the connectors.

  1. Engage the 5 clips and install the instrument lower cover.

  1. Install the bolt <B>.



23. INSTALL INSTRUMENT LOWER PANEL
  1. Install the lower instrument panel LH with the 3 bolts <B>.



24. INSTALL INSTRUMENT LOWER PANEL FINISH PANEL SUB-ASSEMBLY
  1. Engage the 2 clips and install the instrument panel lower finish panel sub-assembly RH.

  1. Install the bolt <B>.



25. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    B290404
  1. Pull the bottom of the stopper.



    B290405
  1. Attach the stopper to the glove compartment door as shown in the illustration.



    E232355
  1. Install the glove compartment door assembly with 3 hinges, holding it horizontal.



    E232356
  1. Slightly deform the upper part of the glove compartment door assembly, and install the glove compartment door assembly.



26. INSTALL INSTRUMENT CENTER CLUSTER FINISH PANEL SUB-ASSEMBLY
  1. Engage the 10 clips and install the instrument cluster center finish panel sub-assembly.



27. INSTALL COMBINATION METER ASSEMBLY
  1. Connect the 2 connectors.

  1. Install the combination meter assembly with the 4 screws <E>.

    Torque:
    1.7 N*m{ 17 kgf*cm , 15 in.*lbf }



28. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
  1. Connect the connectors.

  1. Engage the 6 clips and install the instrument cluster finish panel sub-assembly.

  1. Install the 2 clips.



29. INSTALL INSTRUMENT LOWER PANEL FINISH PANEL
  1. Connect the connectors.

  1. Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.

  1. Install the 2 bolts <B>.



30. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B088394
  1. Connect the hood lock control cable assembly.



    B088397E01
  1. Engage the 2 claws and install the hood lock control lever sub-assembly.



31. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET
  1. Connect all the connectors.

  1. Connect the plug.

  1. Engage the 5 clips and install the radio receiver assembly with bracket.

  1. Install the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



32. INSTALL AIR CONDITIONING CONTROL ASSEMBLY


    E212050
  1. Connect the 2 connectors.

  1. Engage the 4 clips and install the air conditioning control assembly.



33. INSTALL FRONT CONSOLE BOX
  1. for Automatic Transmission on Separate Seat Type:

    1. Install the front console box .

  1. for Automatic Transmission on Bench Seat Type:

    1. Install the front console box .

  1. for Manual Transmission on Separate Seat Type:

    1. Install the front console box .

  1. for Manual Transmission on Bench Seat Type:

    1. Install the front console box .



34. INSTALL INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type)
  1. Engage the 2 clips and 4 claws, and install the instrument panel cup holder tray.

  1. Install the 2 instrument panel cup holders.



35. INSTALL REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type)


    B290408
  1. Engage the 4 claws and install the console box rear.

  1. Install the 2 screws <F> and 2 bolts <B>.

  1. Install the console box carpet.



36. INSTALL REAR CONSOLE UPPER PANEL SUB-ASSEMBLY
  1. for Automatic Transmission on Separate Seat Type:

    1. Install the rear console upper panel sub-assembly .

  1. for Manual Transmission on Separate Seat Type:

    1. Install the rear console upper panel sub-assembly .



37. INSTALL INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake)
  1. Engage the 4 clips and 2 claws, and install the instrument panel under tray.



38. INSTALL INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake)
  1. Engage the 4 clips and install the instrument panel hole cover.



39. INSTALL FRONT PILLAR GARNISH LH
  1. for LH Side:

    1. Install the 3 wire harness clamps.

  1. Engage the claw and clip, and install the front pillar garnish.

  1. Tighten the 2 screws.



    B087471E01
  1. Engage the 2 claws and install the assist grip plug.



40. INSTALL FRONT PILLAR GARNISH RH

HINT:
Follow the same procedures as for the front pillar garnish LH.



41. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.



42. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Follow the same procedures as for the front door opening trim weatherstrip LH.



43. INSTALL COWL SIDE TRIM BOARD LH
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



44. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Follow the same procedures as for the cowl side trim board LH.



45. INSTALL FRONT DOOR SCUFF PLATE LH
  1. Engage the 8 claws and clip, and install the front door scuff plate.



46. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Follow the same procedures as for the front door scuff plate LH.



47. INSTALL FRONT FLOOR FOOTREST


    B087437E01
  1. Engage the 2 clips and install the front floor footrest.



48. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



49. INSPECT SRS WARNING LIGHT
(Click here)