Home › BODY › INTERIOR › ROOF HEADLINING (for Regular Cab)

ROOF HEADLINING (for Regular Cab) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



3. REMOVE FRONT FLOOR FOOTREST


    B087437E01
  1. Disengage the 2 clips and remove the front floor footrest.



4. REMOVE FRONT DOOR SCUFF PLATE LH


    B087476E01
  1. Disengage the 8 claws and clip, and remove the front door scuff plate.



5. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Follow the same procedures as for the front door scuff plate LH.



6. REMOVE COWL SIDE TRIM BOARD LH


    B087438E01
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board.



7. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Follow the same procedures as for the cowl side trim board LH.



8. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B087477E01
  1. Remove the front door opening trim weatherstrip.



9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Follow the same procedures as for the front door opening trim weatherstrip LH.



10. REMOVE FRONT PILLAR GARNISH LH


    B087443E03
  1. Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Follow the same procedures as for the opposite side.



    B087444E01
  1. Remove the 2 screws.

  1. Disengage the clip and claw and remove the front pillar garnish.



    B290414
  1. for LH Side:

    1. Using a clip remover, remove the 3 wire harness clamps.



11. REMOVE FRONT PILLAR GARNISH RH

HINT:
Follow the same procedures as for the front pillar garnish LH.



12. REMOVE INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake)


    B085766E01
  1. Disengage the 4 clips and 2 claws, and remove the instrument panel under tray.



13. REMOVE INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake)


    B085767E01
  1. Disengage the 4 clips and remove the instrument panel hole cover.



14. REMOVE REAR CONSOLE UPPER PANEL SUB-ASSEMBLY
  1. for Automatic Transmission on Separate Seat Type:

    1. Remove the rear console upper panel sub-assembly .

  1. for Manual Transmission on Separate Seat Type:

    1. Remove the rear console upper panel sub-assembly .



15. REMOVE REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type)


    B290398
  1. Remove the console box carpet.



    B290399
  1. Remove the 2 screws <F> and 2 bolts <B>.

  1. Disengage the 4 claws and remove the rear console box assembly.



16. REMOVE INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type)


    B290400
  1. Remove the 2 instrument panel cup holders.



    B290401
  1. Disengage the 2 clips and 4 claws, and remove the instrument panel cup holder tray.



17. REMOVE FRONT CONSOLE BOX
  1. for Automatic Transmission on Separate Seat Type:

    1. Remove the front console box .

  1. for Manual Transmission on Separate Seat Type:

    1. Remove the front console box .

  1. for Automatic Transmission on Bench Seat Type:

    1. Remove the front console box .

  1. for Manual Transmission on Bench Seat Type:

    1. Remove the front console box .



18. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    E212043E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 clips and remove the air conditioner control assembly.
    Text in Illustration 
    *1
    Protective Tape

  1. Disconnect the 2 connectors.



19. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET


    E232403
  1. Remove the 4 bolts.

  1. Disengage the 5 clips and remove the radio receiver assembly with bracket.

    NOTICE:
    Be careful not to damage the clips.

  1. Disconnect the plug.

  1. Disconnect all the connectors.



20. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B088397E01
  1. Disengage the 2 claws.



    B088394
  1. Disconnect the hood lock control cable assembly and remove the hood lock control lever sub-assembly.



21. REMOVE INSTRUMENT LOWER PANEL FINISH PANEL


    B085780E01
  1. Remove the 2 bolts <B>.

  1. Disengage the 3 clips and remove the lower No. 1 instrument panel finish panel.

  1. Disconnect the connectors.



22. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    E232348
  1. Remove the 2 clips.

  1. Disengage the 6 clips and remove the instrument cluster finish panel sub-assembly.

  1. Disconnect the connectors.



23. REMOVE COMBINATION METER ASSEMBLY


    B085782E01
  1. Remove the 4 screws <E> and the combination meter assembly.

  1. Disconnect the 2 connectors.



24. REMOVE INSTRUMENT CENTER CLUSTER FINISH PANEL SUB-ASSEMBLY


    E232349
  1. Disengage the 10 clips and remove the instrument cluster center finish panel sub-assembly.



25. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    E232350
  1. Disengage the claw and separate the glove compartment door stopper from the glove compartment door assembly.

  1. Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.



    E232351
  1. Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.

  1. Remove the glove compartment door stopper.



26. REMOVE INSTRUMENT LOWER PANEL FINISH PANEL SUB-ASSEMBLY


    E232352
  1. Remove the bolt <B>.

  1. Disengage the 2 clips and remove the instrument panel lower finish panel sub-assembly RH.



27. REMOVE INSTRUMENT LOWER PANEL


    B085788E01
  1. Remove the 3 bolts <B> and the lower instrument panel LH.



28. REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY


    E232353
  1. Remove the bolt <B>.

  1. Disengage the 5 clips and remove the instrument lower cover sub-assembly.

  1. Disconnect the connectors.



29. REMOVE INSTRUMENT SIDE PANEL


    E232354E01
  1. Using a screwdriver, disengage the 3 claws and remove the instrument side panel RH.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



30. DISCONNECT PASSENGER AIRBAG CONNECTOR


F050426E01
  1. Disconnect the airbag connector.



31. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY


    E232399E01
  1. Tape the steering column cover upper and steering wheel sub-assembly with protective tape.
    Text in Illustration 
    *1
    Protective Tape

  1. Disengage the 4 clamps and disconnect the 4 connectors.



  1. Remove the 8 bolts, nut and instrument panel sub-assembly with passenger airbag assembly.


    E232400E01



32. REMOVE BACK PANEL TRIM COVER


    B087479E01
  1. for Separate Seat Type and Bench Seat Type:

    HINT:
    Follow the same procedures as for the opposite side (for Bench Seat Type).


    1. Disengage the 6 claws and remove the back panel trim cover.



    B087478E01
  1. for Bench Seat Type:

    1. Disengage the 6 claws and remove the back panel trim cover.



33. REMOVE BACK PANEL UPPER GARNISH


    B087480E01
  1. Disengage the 4 claws and 5 clips, and remove the back panel upper garnish.



34. REMOVE JACK ASSEMBLY (for Separate Seat Type)


35. REMOVE BACK PANEL TRIM COVER (for Separate Seat Type)


    B087481E01
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the back panel trim cover.



36. REMOVE BACK PANEL TRIM (for Separate Seat Type)


    B087482E01
  1. Remove the 4 clips and back panel trim.



37. REMOVE QUARTER TRIM LOWER PANEL LH


    B087483E01
  1. Disengage the 2 claws and 3 clips, and remove the quarter trim lower panel.



38. REMOVE QUARTER TRIM LOWER PANEL RH

HINT:
Follow the same procedures as for the quarter trim lower panel LH.



39. REMOVE QUARTER INSIDE TRIM BOARD LH


    B087324E01
  1. for LH Side and Separate Seat Type RH side:

    1. Remove the bolt and the floor anchor of the front seat outer belt.



    B290463
  1. for Bench Seat Type RH Side:

    1. Remove the bolt and the floor anchor of the front seat outer belt.

    2. Disconnect the belt tension sensor connector.

    3. Remove the wiring harness clamp.



    B087484E03
  1. Using a screwdriver with its tip taped in protective tape, disengage the claw and open the cover.
    Text in Illustration 
    *1
    Protective Tape



    B087485E01
  1. Remove the 3 screws.

  1. Disengage the 2 clips and remove the quarter trim board.



40. REMOVE QUARTER INSIDE TRIM BOARD RH

HINT:
Follow the same procedures as for the quarter trim board LH.



41. REMOVE ROOM LIGHT ASSEMBLY


    E232366E01
  1. Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the room light lens.
    Text in Illustration 
    *1
    Protective Tape



    B087455E03
  1. Using a screwdriver with its tip taped in protective tape, disengage the 3 claws.
    Text in Illustration 
    *1
    Protective Tape

  1. Disconnect the room light connector and remove the room light.



42. REMOVE ASSIST GRIP PLUG

HINT:
Follow the same procedures as for the opposite side.



    B205278E03
  1. Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and open the cover.
    Text in Illustration 
    *1
    Protective Tape



    B205279
  1. Remove the screw.

  1. Disengage the claw and remove the assist grip plug.



43. REMOVE VISOR ASSEMBLY LH


    B087457E01
  1. Remove the 2 screws.

  1. Remove the visor from the visor holder.



44. REMOVE VISOR ASSEMBLY RH

HINT:
Follow the same procedures as for the visor assembly LH.



45. REMOVE VISOR HOLDER

HINT:
Follow the same procedures as for the opposite side.



    B087458E02
  1. Turn the visor holder 90° counterclockwise and remove it.



46. REMOVE COAT HOOK

HINT:
Follow the same procedures as for the opposite side.



    B087459E02
  1. Turn the coat hook 90° counterclockwise and remove it.



47. REMOVE ROOF HEADLINING ASSEMBLY


    B290416
  1. Disconnect the 3 roof wire connectors.

  1. Using a clip remover, remove the wire harness clamps.



    B087486E01
  1. Remove the roof headlining from the vehicle.



48. REMOVE ROOF HEADLINING PAD


    B087487E01
  1. Remove the roof headlining pad from the roof headlining.



49. REMOVE ROOF WIRE


    B087488E01
  1. Remove the 5 adhesive tapes and roof wire.