Home › BODY › INTERIOR › ROOF HEADLINING (for Double Cab)

ROOF HEADLINING (for Double Cab) > INSTALLATION

for Preparation Click here



1. INSTALL ROOF WIRE


  1. w/ Vanity Light:



      E232368
    1. Install the roof wire with 20 new tapes, as shown in the illustration.



  1. w/o Vanity Light:



      E232407
    1. Install the roof wire with 9 new tapes, as shown in the illustration.



2. INSTALL ROOF HEADLINING PAD


    B087429E04
  1. Install 2 new roof headlining pads onto the roof headlining.
    Text in Illustration 
    *a
    Grooves



3. INSTALL ROOF HEADLINING ASSEMBLY


    B087430E01
  1. Install the roof headlining into the vehicle.

  1. Install the wire harness clamps.

  1. Connect the 3 roof wire connector.



4. INSTALL COAT HOOK

HINT:
Follow the same procedures as for the opposite side.



    B087466E02
  1. Turn the coat hook 90° clockwise and install it.



5. INSTALL VISOR HOLDER

HINT:
Follow the same procedures as for the opposite side.



    B087467E02
  1. Turn the visor holder 90° clockwise and install it.



6. INSTALL VISOR ASSEMBLY LH
  1. Install the visor into the visor holder.

  1. Tighten the 2 screws.



7. INSTALL VISOR ASSEMBLY RH

HINT:
Follow the same procedures as for the visor assembly LH.



8. INSTALL ASSIST GRIP PLUG (w/ Curtain Shield Airbag)

HINT:
Follow the same procedures as for the opposite side.

  1. Engage the claw and install the assist grip plug.

  1. Tighten the screw.



    B087594E01
  1. Engage the 2 claws and close the cover.



9. INSTALL ASSIST GRIP SUB-ASSEMBLY

HINT:
Follow the same procedures as for the opposite side.

  1. Install the assist grip with the 2 screws.



    B087431E01
  1. Engage the 2 claws and close the cover.



10. INSTALL ROOF CONSOLE BOX ASSEMBLY
  1. Install the wire harness clamp.

  1. Connect the connectors.

  1. Engage the 2 clips and 3 claws and install the roof console box assembly.

  1. Tighten the screw.



11. INSTALL ROOM LIGHT ASSEMBLY


    B087468E01
  1. Connect the room light connector.

  1. Engage the 3 claws and install the room light.



    E232392
  1. Engage the 2 claws and install the room light lens.



12. INSTALL QUARTER INSIDE TRIM BOARD LH
  1. Engage the 2 clips and install the quarter inside trim board.

  1. Tighten the 3 screws.



    B087432E01
  1. Engage the claw and close the cover.



    B087330E04
  1. Install the floor anchor of the rear seat belt outer with the bolt.
    Text in Illustration 
    *a
    Convex

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

    NOTICE:
    1. Make sure that the rear seat outer belt is oriented in the correct direction when installing.
    2. Be careful not to place the rear seat outer belt over the convex areas of the floor panel.



13. INSTALL QUARTER INSIDE TRIM BOARD RH

HINT:
Follow the same procedures as for the quarter inside trim board LH.



14. INSTALL QUARTER TRIM LOWER PANEL LH
  1. Engage the 2 claws and 2 clips, and install the quarter trim lower panel.



15. INSTALL QUARTER TRIM LOWER PANEL RH

HINT:
Follow the same procedures as for the quarter trim lower panel LH.



16. INSTALL LUGGAGE COMPARTMENT SIDE TRAY RH
  1. w/ Woofer:

    1. Engage the 5 claws and 7 clips, and install the luggage compartment side tray.

    2. Tighten the bolt.

  1. w/o Woofer:

    1. Engage the 5 claws and 5 clips, and install the luggage compartment side tray.

    2. Tighten the 3 bolts.



17. INSTALL REAR SEAT BACK CENTER HINGE SUB-ASSEMBLY


    B087197E01
  1. Install the rear seat back center hinge with the 2 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 14 ft.*lbf }



18. INSTALL LUGGAGE COMPARTMENT SIDE TRAY LH
  1. Engage the 8 claws and 3 clips, and install the luggage compartment side tray.

  1. Tighten the 3 bolts.



19. INSTALL CENTER PILLAR UPPER GARNISH LH
  1. Engage the clip and install the center pillar upper garnish.

  1. Tighten the 2 screws.



20. INSTALL CENTER PILLAR UPPER GARNISH RH

HINT:
Follow the same procedures as for the center pillar upper garnish LH.



21. INSTALL CENTER PILLAR LOWER GARNISH LH
  1. Engage the 2 claws and 2 clips, and install the center pillar lower garnish.

  1. Install the floor anchor of the front seat outer belt with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }



22. INSTALL CENTER PILLAR LOWER GARNISH RH

HINT:
Follow the same procedures as for the center pillar lower garnish LH.



23. INSTALL LAP BELT OUTER ANCHOR COVER

HINT:
Follow the same procedures as for the opposite side.

  1. Engage the 3 claws and install the lap belt outer anchor cover.



24. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
  1. Install the instrument panel sub-assembly with passenger airbag assembly with the 8 bolts and nut.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf } for bolt <C>

  1. Engage the 5 clamps and connect the 4 connectors.

  1. Remove the protective tape from the steering column cover upper and steering wheel sub-assembly.



25. CONNECT PASSENGER AIRBAG CONNECTOR


26. INSTALL INSTRUMENT SIDE PANEL


    B085791E01
  1. Engage the 3 claws and install the instrument side RH.



27. INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY
  1. Connect the connectors.

  1. Engage the 5 clips and install the instrument lower cover.

  1. Install the bolt <B>.



28. INSTALL INSTRUMENT LOWER PANEL
  1. Install the lower instrument panel LH with the 3 bolts <B>.



29. INSTALL INSTRUMENT LOWER PANEL FINISH PANEL SUB-ASSEMBLY
  1. Engage the 2 clips and install the instrument panel lower finish panel sub-assembly RH.

  1. Install the bolt <B>.



30. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    B290404
  1. Pull the bottom of the stopper.



    B290405
  1. Attach the stopper to the glove compartment door as shown in the illustration.



    E232355
  1. Install the glove compartment door assembly with 3 hinges, holding it horizontal.



    E232356
  1. Slightly deform the upper part of the glove compartment door assembly, and install the glove compartment door assembly.



31. INSTALL INSTRUMENT CENTER CLUSTER FINISH PANEL SUB-ASSEMBLY
  1. Engage the 10 clips and install the instrument cluster center finish panel sub-assembly.



32. INSTALL COMBINATION METER ASSEMBLY
  1. Connect the 2 connectors.

  1. Install the combination meter assembly with the 4 screws <E>.

    Torque:
    1.7 N*m{ 17 kgf*cm , 15 in.*lbf }



33. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
  1. Connect the connectors.

  1. Engage the 6 clips and install the instrument cluster finish panel sub-assembly.

  1. Install the 2 clips.



34. INSTALL INSTRUMENT LOWER PANEL FINISH PANEL
  1. Connect the connectors.

  1. Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.

  1. Install the 2 bolts <B>.



35. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B088394
  1. Connect the hood lock control cable assembly.



    B088397E01
  1. Engage the 2 claws and install the hood lock control lever sub-assembly.



36. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)
  1. Connect all the connectors.

  1. Engage the 5 clips and install the radio and display receiver assembly with bracket.

  1. Install the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



37. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)
  1. Connect all the connectors.

  1. Connect the plug.

  1. Engage the 5 clips and install the radio receiver assembly with bracket.

  1. Install the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



38. INSTALL AIR CONDITIONING CONTROL ASSEMBLY


    E212050
  1. Connect the 2 connectors.

  1. Engage the 4 clips and install the air conditioning control assembly.



39. INSTALL FRONT CONSOLE BOX
  1. for Automatic Transmission:

    1. Install the front console box .

  1. for Manual Transmission:

    1. Install the front console box .



40. INSTALL INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission)
  1. Engage the 2 clips and 4 claws, and install the instrument panel cup holder tray.

  1. Install the 2 instrument panel cup holders.



41. INSTALL REAR CONSOLE BOX ASSEMBLY


    B290408
  1. Engage the 4 claws and install the console box rear.

  1. Install the 2 screws <F> and 2 bolts <B>.

  1. Install the console box carpet.



42. INSTALL REAR CONSOLE UPPER PANEL SUB-ASSEMBLY
  1. for Automatic Transmission:

    1. Install the rear console upper panel sub-assembly .

  1. for Manual Transmission:

    1. Install the rear console upper panel sub-assembly .



43. INSTALL INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake)
  1. Engage the 4 clips and 2 claws, and install the instrument panel under tray.



44. INSTALL INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake)
  1. Engage the 4 clips and install the instrument panel hole cover.



45. INSTALL FRONT PILLAR GARNISH LH
  1. Install the 3 wire harness clamps (LH side only).

  1. Engage the claw and clip, and install the front pillar garnish.

  1. Tighten the 2 screws.



    B087471E01
  1. Engage the 2 claws and install the assist grip plug.

    HINT:
    Follow the same procedures as for the opposite side.



46. INSTALL FRONT PILLAR GARNISH RH

HINT:
Follow the same procedures as for the front pillar garnish LH.



47. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the rear door opening trim weatherstrip.



48. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Follow the same procedures as for the rear door opening trim weatherstrip.



49. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.



50. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Follow the same procedures as for the front door opening trim weatherstrip.



51. INSTALL REAR DOOR SCUFF PLATE LH
  1. Engage the 8 claws and install the rear door scuff plate.



52. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Follow the same procedures as for the rear door scuff plate LH.



53. INSTALL COWL SIDE TRIM BOARD LH
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



54. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Follow the same procedures as for the cowl side trim board LH.



55. INSTALL FRONT DOOR SCUFF PLATE LH
  1. Engage the 9 claws and install the front door scuff plate.



56. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Follow the same procedures as for the front door scuff plate LH.



57. INSTALL REAR SEAT BACK HINGE SUB-ASSEMBLY LH


    B087196E01
  1. Install the rear seat back hinge with the 2 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 14 ft.*lbf }



58. INSTALL REAR SEAT BACK HINGE SUB-ASSEMBLY RH

HINT:
Follow the same procedures as for the rear seat back hinge sub-assembly LH.



59. INSTALL FRONT FLOOR FOOTREST


    B087437E01
  1. Engage the 2 clips and install the front floor footrest.



60. INSTALL REAR SEAT BACK ASSEMBLY LH


    B087195E01
  1. Install the rear seat back with the 2 bolts.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



61. INSTALL REAR SEAT BACK ASSEMBLY RH


    B087217
  1. Install the rear seat back with the 2 bolts.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



    B087239E03
  1. Install the rear seat belt inner and rear seat belt outer center of the floor anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

    NOTICE:
    1. Make sure that the rear seat inner belt and floor anchor of the rear center seat outer belt are oriented in the correct direction when installing.
    2. Be careful not to place the rear seat inner belt (and floor anchor of the rear center seat outer belt) over the convex areas of the floor panel.



62. INSTALL REAR SEAT BACK HINGE COVER
  1. for LH Side:

    1. Install the rear seat back hinge cover .

  1. for RH Side:

    1. Install the rear seat back hinge cover .



63. INSTALL REAR SEAT CUSHION ASSEMBLY LH


    B087193E01
  1. Install the rear seat cushion with the 2 bolts.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



64. INSTALL REAR SEAT CUSHION ASSEMBLY RH


    B087214E01
  1. Install the rear seat cushion with the 2 bolts.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



65. INSTALL FRONT SEAT ASSEMBLY LH


    B087375E01
  1. Place the front seat in the cabin.

  1. Tighten the 2 bolts on the front side of the front seat.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Tighten the 2 bolts on the rear side of the front seat.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



    B087646E01
  1. Install the wire harness clamp.

  1. Connect the 2 connectors.

  1. Connect the airbag connector.



66. INSTALL FRONT SEAT ASSEMBLY RH
  1. for Separate Folding Seat Type:

    1. Install the front seat assembly RH .

  1. for Separate Seat Type Front Passenger Side:

    1. Install the front seat assembly RH .



67. INSTALL SEAT TRACK COVER LH


B087374E01

HINT:
Follow the same procedures as for the opposite side.

  1. Engage the 2 claws and install the seat track cover.



68. INSTALL SEAT TRACK COVER RH
  1. for Separate Folding Seat Type:

    1. Install the seat track cover RH .

  1. for Separate Seat Type Front Passenger Side:

    1. Install the seat track cover RH .



69. INSTALL INNER REAR VIEW MIRROR COVER (w/ EC Mirror)
  1. Connect the connector.



    B227101
  1. Engage the 2 claws of the inner rear view mirror cover to the mirror, and then slide the inner rear view mirror cover in the direction indicated by the arrow in the illustration to engage the 2 claws to the roof headlining and install the inner rear view mirror cover.



70. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



71. INSPECT SRS WARNING LIGHT
(Click here)