Home › BODY › EXTERIOR › FRONT BUMPER

FRONT BUMPER > INSTALLATION

for Preparation Click here



1. INSTALL FRONT BUMPER EXTENSION SUB-ASSEMBLY LH
  1. Install the front bumper extension with the 3 nuts.

    Torque:
    58 N*m{ 590 kgf*cm , 43 ft.*lbf }



2. INSTALL FRONT BUMPER EXTENSION SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



3. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
  1. Install the front bumper reinforcement with the 6 nuts.

    Torque:
    58 N*m{ 590 kgf*cm , 43 ft.*lbf }



4. INSTALL FRONT BUMPER ARM MOUNTING BRACKET LH
  1. Install the front bumper arm mounting bracket with the 2 bolts.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



5. INSTALL FRONT BUMPER ARM MOUNTING BRACKET RH

HINT:
Use the same procedure as for the LH side.



6. INSTALL FRONT BUMPER UPPER SIDE RETAINER

HINT:
Follow the same procedures as for the opposite side.

  1. Engage the 2 claws and install the front bumper upper side retainer.



7. INSTALL FRONT BUMPER REINFORCEMENT EXTENSION LH
  1. Install the front bumper reinforcement extension with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



8. INSTALL FRONT BUMPER REINFORCEMENT EXTENSION RH

HINT:
Use the same procedure as for the LH side.



9. INSTALL BUMPER FILLER RETAINER

HINT:
Follow the same procedures as for the opposite side.

  1. Install the bumper filler retainer with the screw.



10. INSTALL FRONT BUMPER UPPER CENTER RETAINER
  1. Install the front bumper upper center retainer with the 4 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



11. INSTALL HEADLIGHT ASSEMBLY LH
  1. Connect the 3 connectors.

  1. Engage the clamp and install the headlight assembly with the bolt and 2 screws.

    Torque:
    for Bolt:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



12. INSTALL HEADLIGHT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



13. INSTALL FRONT BUMPER SIDE SUPPORT

HINT:
Follow the same procedures as for the opposite side.

  1. Engage the claw and install the front bumper side support.

  1. Tighten the screw.



14. INSTALL FOG LIGHT COVER LH
  1. Engage the claw and the 2 guides, install the fog light cover.

  1. Install the retainer.



15. INSTALL FOG LIGHT COVER RH

HINT:
Use the same procedure as for the LH side.



16. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)
  1. Engage the 2 guides and install the fog light assembly.

  1. Tighten the 2 screws.



17. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure as for the LH side.



18. INSTALL FRONT BUMPER HOLE COVER LH (w/o Fog Light)
  1. Engage the 2 guides and install the front bumper hole cover.

  1. Tighten the 2 screws.



19. INSTALL FRONT BUMPER HOLE COVER RH (w/o Fog Light)

HINT:
Use the same procedure as for the LH side.



20. INSTALL LOWER RADIATOR GRILLE (for 4WD and Pre-Runner)
  1. Engage the 13 claws and install the lower radiator grille.

  1. Install the 5 retainers.



21. INSTALL LOWER RADIATOR GRILLE (for X-Runner)
  1. Engage the 12 claws and install the lower radiator grille.

  1. Install the 5 retainers.



22. INSTALL FRONT BUMPER EXTENSION LH (for 4WD and Pre-Runner)
  1. Install the front bumper extension with the 7 retainers.



23. INSTALL FRONT BUMPER EXTENSION RH (for 4WD and Pre-Runner)

HINT:
Use the same procedure as for the LH side.



24. INSTALL FRONT BUMPER EXTENSION LH (for X-Runner)
  1. Install the front bumper extension with the 5 retainers.



25. INSTALL FRONT BUMPER EXTENSION RH (for X-Runner)

HINT:
Use the same procedure as for the LH side.



26. INSTALL FRONT SPOILER COVER LH (for X-Runner)
  1. Install the front spoiler cover with the 6 retainers.

  1. Install the 3 clips and the retainer.



27. INSTALL FRONT SPOILER COVER RH (for X-Runner)
  1. Install the front spoiler cover with the 6 retainers.

  1. Install the 2 clips and the retainer.



28. INSTALL FRONT BUMPER COVER
  1. Install the 4 clips.

  1. Engage the 2 claws and install the front bumper cover.

  1. Connect the 2 fog light connectors.

    HINT:
    If the vehicle is equipped with fog lights, connect the connector.

  1. Install the 2 bolts and the 4 screws.

  1. Install the 3 clips.



    E212079E01
  1. Install the pin hold clip.
    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    Insert the pin hold clip with the slot aligned vertically. Do not rotate the clip after inserting it. After installation, confirm that the slot is vertical.

    HINT:
    Use the same procedure for the remaining parts.

  1. Install the screw.

    HINT:
    Use the same procedure for the remaining parts.



29. INSTALL FRONT BUMPER FILLER LH
  1. Engage the clip and guide, install the front bumper filler.



30. INSTALL FRONT BUMPER FILLER RH

HINT:
Use the same procedure as for the LH side.



31. INSTALL RADIATOR GRILLE
  1. Engage the 8 guides and install the radiator grille.

  1. Install the 2 clips.

  1. Tighten the 2 screws.



32. PREPARE VEHICLE FOR HEADLIGHT AIMING ADJUSTMENT
  1. Prepare the vehicle:

    1. Ensure that there is no damage or deformation to the body around the headlights.
    2. Fill the fuel tank.
    3. Make sure that the oil is filled to the specified level.
    4. Make sure that the coolant is filled to the specified level.
    5. Inflate the tires to the appropriate pressure.
    6. Place the spare tire, tools, and jack in their original positions.
    7. Unload the trunk.
    8. Sit a person of average weight (68 kg, 150 lb) in the driver side seat.



33. PREPARE FOR HEADLIGHT AIMING (for Using a Tester)
  1. Prepare the vehicle for headlight aim check.

  1. Perform adjustment in accordance with the headlight tester instructions.



34. PREPARE FOR HEADLIGHT AIMING (for Using a Screen)
  1. Prepare the vehicle according to the following conditions:

    1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.
    2. Place the vehicle at a 90° angle to the wall.
    3. Keep a 7.62 m (25 ft) distance between the center of the headlight bulb and the wall.
    4. Place the vehicle on a level surface.
    5. Bounce the vehicle up and down to settle the suspension.

    NOTICE:
    A distance of 7.62 m (25 ft) between the vehicle (center of the headlight bulb) and the wall is necessary for proper aim adjustment. If unavailable to secure a distance of 7.62 m (25 ft), secure a distance of exactly 3 m (9.84 ft) to check and adjust the headlight aim. (Since the target zone will change with the distance, follow the instructions shown in the illustration.)

  1. Prepare a piece of thick white paper (approximately 2 m (6.6 ft) (height) x 4 m (13.1 ft) (width)) to use as a screen.

  1. Draw a vertical line down the center of screen (V line).



  1. Set the screen as shown in the illustration.


    E076099E02

    HINT:
    1. Stand the screen perpendicular to the ground.
    2. Align the V line on the screen with the center of the vehicle.



    I033423E27
  1. Draw base lines (H line, V LH, V RH lines) on the screen as shown in the illustration.
    Text in Illustration 
    *a
    V LH Line
    *b
    V Line
    *c
    V RH Line
    *d
    H Line
    *e
    Ground

    HINT:
    1. The base lines differ for "low-beam inspection" and "high-beam inspection".
    2. Follow the same procedures as for "high-beam inspection".
    3. Mark the headlight bulb center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight bulb or the manufacturer name marked on the headlight as the center mark.


    1. H Line (Headlight height):
      Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low-beam headlights.

    2. V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) headlights):
      Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low-beam headlight bulbs).



35. INSPECT HEADLIGHT AIMING
  1. Cover the headlight or disconnect the connector of the headlight on the opposite side to prevent light from the headlight not being inspected from affecting headlight aiming inspection.

    NOTICE:
    Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, and may easily melt or be damaged due to heat.

  1. Start the engine.

    NOTICE:
    Engine speed must be 1,500 or more.



  1. Turn on the headlight and make sure that the cutoff line falls within the specified area, as shown in the illustration.


    E113067E02

    HINT:
    1. Alignment distance is 7.62 m (25 ft):
      The cutoff line is 101 mm (3.97 in.) above and below the H line as well as to the left and right of the V line with low-beam (SAEJ599).
    2. Alignment distance is 3 m (9.84 ft):
      The cutoff line is 40 mm (1.57 in.) above and below the H line as well as to the left and right of the V line with low-beam (SAEJ599).
    3. Alignment distance is 7.62 m (25 ft):
      The center of intensity is 101 mm (3.97 in.) above and below the H line as well as to the left and right of the V line with high-beam (SAEJ599).
    4. Alignment distance is 3 m (9.84 ft):
      The center of intensity is 40 mm (1.57 in.) above and below the H line as well as to the left and right of the V line with high-beam (SAEJ599).
    5. Alignment distance is 7.62 m (25 ft):
      The right half of the low beam cutoff line should be on the H line (preferred cutoff line target).
    6. Alignment distance is 3 m (9.84 ft):
      The right half of the low beam cutoff line should be on the H line (preferred cutoff line target).



36. ADJUST HEADLIGHT AIMING


    E212100E01
  1. Adjust the aim vertically:
    Adjust the headlight aim into the specified range by turning aiming screw A with a screwdriver.

    NOTICE:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.

  1. Perform low-beam aim adjustment.

    HINT:
    The headlight aim moves up when turning the aiming screw clockwise, and moves down when turning the aiming screw counterclockwise.



    E212101E01
  1. Adjust the aim horizontally:
    Adjust the headlight aim into the specified range by turning aiming screw B with a screwdriver.

    NOTICE:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.



37. PREPARE VEHICLE FOR FOG LIGHT AIMING ADJUSTMENT
  1. Prepare the vehicle:

    HINT:
    1. Ensure that there is no damage or deformation to the body around the fog lights.
    2. Fill the fuel tank.
    3. Make sure that the oil is filled to the specified level.
    4. Make sure that the coolant is filled to the specified level.
    5. Inflate the tires to the appropriate pressure.
    6. Place the spare tire, tools, and jack in their original positions.
    7. Unload the trunk.
    8. Sit a person of average weight (68 kg, 150 lb) in the driver side seat.



38. PREPARE FOR FOG LIGHT AIMING


E076102E02
  1. Prepare the vehicle according to the following conditions:
    Text in Illustration 
    *a
    90°
    *b
    7.62 or 3 m

    HINT:
    1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.
    2. Place the vehicle at a 90° angle to the wall.
    3. Keep a 7.62 m (25 ft) distance between the center of the fog light bulb and the wall.
    4. Place the vehicle on a level surface.
    5. Bounce the vehicle up and down to settle the suspension.

    NOTICE:
    A distance of 7.62 m (25 ft) between the vehicle (center of the fog light bulb) and the wall is necessary for proper aim adjustment. If unavailable to secure a distance of 7.62 m (25 ft), secure a distance of exactly 3 m (9.84 ft) to check and adjust the fog light aim. (Since the target zone will change with the distance, follow the instructions shown in the illustration.)

  1. Prepare a piece of thick white paper (approximately 2 m (6.6 ft) (height) x 4 m (13.1 ft) (width)) to use as a screen.

  1. Draw a vertical line down the center of screen (V line).



  1. Set the screen as shown in the illustration.


    E076103E02

    HINT:
    1. Stand the screen perpendicular to the ground.
    2. Align the V line on the screen with the center of the vehicle.



    I033423E27
  1. Draw base lines (H line, V LH, V RH lines) on the screen as shown in the illustration.
    Text in Illustration 
    *a
    V LH Line
    *b
    V Line
    *c
    V RH Line
    *d
    H Line
    *e
    Ground

    HINT:
    Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb or the manufacturer's name marked on the fog light as the center mark.


    1. H Line (Fog light height):
      Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the low-beam fog lights.

    2. V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):
      Draw two vertical lines so that they intersect the H line at each center mark.



39. INSPECT FOG LIGHT AIMING
  1. Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light not being inspected from affecting fog light aiming inspection.

  1. Start the engine.

    NOTICE:
    Engine speed must be 1500 or more.



  1. Turn on the fog light and make sure that the cutoff line falls within the specified area, as shown in the illustration.


    I041221E53



40. ADJUST FOG LIGHT AIMING


E107962
  1. Adjust the fog light aim into the specified range by turning the aiming screw with a screwdriver.

    NOTICE:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, Loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.