COMPRESSOR > REMOVAL |
| 1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM |
Start up the engine.
Turn the A/C switch to ON.
Operate the cooler compressor with an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the compressor oil remaining in each component into the cooler compressor.
Stop the engine.
Recover the refrigerant from the A/C system using a refrigerant recovery unit.
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE FRONT WHEEL LH |
| 4. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for 2TR-FE) |
Remove the 4bolts, then remove the engine under cover No.1.
| 5. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for 1GR-FE) |
Remove the 4 bolts and engine under cover.
| 6. REMOVE V-BANK COVER (for 1GR-FE) |
![]() |
Remove the 2 nuts, then remove the V-bank cover.
| 7. REMOVE RADIATOR SUPPORT TO FRAME SEAL LH (for 1GR-FE) |
![]() |
Disengage the 9 clips, then remove the radiator support to frame seal.
| 8. REMOVE FAN SHROUD (for 1GR-FE) |
![]() |
Disconnect the hose from the radiator reserve tank.
![]() |
Remove the 2 cooler hoses from the clamp (with automatic transmission).
Remove the 4 nuts from the fan pulley.
Remove the fan and generator V belt .
Remove the 2 bolts from the fan shroud.
Remove the fan pulley and fan shroud.
| 9. REMOVE FAN & GENERATOR V BELT (for 2TR-FE) |
![]() |
Turning the hexagonal bolt on the V-ribbed belt tensioner clockwise, loosen and then remove the V belt.
| 10. REMOVE FAN & GENERATOR V BELT (for 1GR-FE) |
![]() |
While releasing the belt tension by turning the belt tensioner counterclockwise, remove the V-ribbed belt from the belt tensioner.
| 11. REMOVE GENERATOR ASSEMBLY (for 1GR-FE) |
![]() |
Disconnect the wire harness.
Remove the bolt and wire harness stay.
Disconnect the connector from the generator assembly.
Remove the terminal cap and nut.
Disconnect the wire harness from terminal B.
![]() |
Remove the 2 bolts, then separate the wire harness clamp bracket from the generator assembly.
![]() |
Remove the 2 bolts, then remove the generator assembly.
| 12. REMOVE FRONT FENDER APRON SEAL UPPER |
![]() |
Using a clip remover, disengage the 5 clips and remove the front fender apron seal upper. (4WD, PRE RUNNER)
![]() |
Using a clip remover, disengage the 6 clips and remove the front fender apron seal upper. (2WD)
| 13. DISCONNECT SUCTION HOSE SUB-ASSEMBLY (for 2TR-FE) |
![]() |
Remove the bolt and separate the suction hose sub-assembly.
Remove the bolt and disconnect the suction hose sub-assembly.
Remove the seal washer from the suction hose sub-assembly.
| 14. DISCONNECT SUCTION HOSE SUB-ASSEMBLY (for 1GR-FE) |
![]() |
Remove the bolt and separate the suction hose sub-assembly.
Remove the bolt and disconnect the suction hose sub-assembly.
Remove the seal washer from the suction hose sub-assembly.
| 15. DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY |
![]() |
Remove the bolt and disconnect the cooler refrigerant discharge hose sub-assembly.
Remove the seal washer from the cooler refrigerant discharge hose sub-assembly.
| 16. REMOVE COMPRESSOR AND MAGNETIC CLUTCH (for 2TR-FE) |
![]() |
Disconnect the connector.
Remove the 4 bolts and harness bracket, and remove the cooler compressor and magnetic clutch.
| 17. REMOVE COMPRESSOR AND MAGNETIC CLUTCH (for 1GR-FE) |
![]() |
Disconnect the connector.
Remove the 4 bolts and cooler compressor and magnetic clutch.