FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > REASSEMBLY |
| 1. INSTALL FRONT DIFFERENTIAL DUST DEFLECTOR |
![]() |
Using a steel plate and a press, install a new dust deflector.
| 2. INSTALL FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING |
![]() |
Using SST and a press, install the bearing.
Using a snap ring expander, install the snap ring.
| 3. INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH |
![]() |
Install the side gear shaft into the differential tube.
Using snap ring pliers, install the snap ring.
| 4. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL |
![]() |
Using SST and a plastic hammer, install a new oil seal.
Coat the oil seal lip with MP grease.
| 5. INSTALL DIFFERENTIAL CLUTCH HUB |
![]() |
Install the clutch hub onto the side gear inter shaft.
Using snap ring pliers, install the snap ring.
| 6. INSTALL FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING |
![]() |
Using SST and a press, install 2 new bearings.
| 7. INSTALL FRONT DIFFERENTIAL CASE |
![]() |
Install the 2 proper thrust washers onto the 2 side gears.
| Thickness mm (in.) | Thickness mm (in.) |
| 1.50 (0.0591) | 1.75 (0.0689) |
| 1.55 (0.0610) | 1.80 (0.0709) |
| 1.60 (0.0630) | 1.85 (0.0728) |
| 1.65 (0.0650) | 1.90 (0.0748) |
| 1.70 (0.0669) | - |
Install the 2 side gears, 2 side gear thrust washers, 2 pinion gears, 2 pinion gear thrust washers and pinion shaft into the differential case assembly.
Measure the side gear backlash.
![]() |
Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case assembly.
![]() |
Using a pin punch and hammer, install the straight pin through the differential case assembly and hole of the pinion shaft.
Stake the differential case assembly.
| 8. INSTALL DIFFERENTIAL RING GEAR |
![]() |
Clean the contact surfaces of the differential case assembly and ring gear.
Heat the ring gear to about 100°C (212°F) in boiling water.
Carefully take the ring gear out of the boiling water.
After any moisture on the ring gear has completely evaporated, quickly install the ring gear onto the differential case assembly.
Temporarily install 10 bolts so that the bolt holes in the ring gear and differential case assembly are aligned.
After the ring gear has cooled sufficiently, tighten the ring gear set bolts to which adhesive has been applied.
| 9. INSTALL FRONT DIFFERENTIAL CASE BEARING |
![]() |
Using SST and a press, install the 2 differential case bearings into the differential case assembly.
| 10. INSTALL SIDE BEARING OUTER RACE |
Install a new plate washer to the side bearing retainer.
![]() |
Using SST and a press, install the bearing outer race onto the differential case bearing retainer assembly.
Install a new plate washer onto the differential carrier assembly.
![]() |
Using SST and a press, install the bearing outer race onto the differential carrier assembly.
| 11. INSTALL FRONT BEARING OUTER RACE |
![]() |
Using SST, install the outer race.
| 12. INSTALL REAR BEARING OUTER RACE |
Install the oil storage ring.
Using SST, install the outer race.
| 13. INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING |
Install the washer onto the drive pinion.
![]() |
Using SST and a press, install the front bearing onto the drive pinion.
| 14. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD |
Install the drive pinion.
![]() |
Using SST, install the rear bearing, oil slinger and companion flange.
Coat the threads of the nut with hypoid gear oil.
![]() |
Adjust the drive pinion preload by tightening the companion flange nut.
Using SST to hold the companion flange, tighten the nut.
![]() |
Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.
| Bearing | Standard |
| New | 0.98 to 1.57 N*m (10 to 16 kgf*cm, 8.7 to 13.9 in.*lbf) |
| Reused | 0.49 to 0.78 N*m (5 to 8 kgf*cm, 4.3 to 6.9 in.*lbf) |
| 15. INSTALL DIFFERENTIAL CASE ASSEMBLY |
| 16. ADJUST BACKLASH DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION |
Install the side bearing retainer with the 10 bolts.
![]() |
Using SST and a dial indicator, measure the ring gear backlash.
If it is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.
| Thickness mm (in.) | Thickness mm (in.) | Thickness mm (in.) |
| 1.58 (0.0622) | 1.78 (0.0701) | 1.98 (0.0780) |
| 1.60 (0.0630) | 1.80 (0.0709) | 2.00 (0.0787) |
| 1.62 (0.0638) | 1.82 (0.0717) | 2.02 (0.0800) |
| 1.64 (0.0646) | 1.84 (0.0724) | 2.04 (0.0803) |
| 1.66 (0.0654) | 1.86 (0.0732) | 2.06 (0.0811) |
| 1.68 (0.0661) | 1.88 (0.0740) | 2.08 (0.0819) |
| 1.70 (0.0669) | 1.90 (0.0748) | 2.10 (0.0827) |
| 1.72 (0.0677) | 1.92 (0.0756) | 2.12 (0.0835) |
| 1.74 (0.0685) | 1.94 (0.0764) | 2.14 (0.0843) |
| 1.76 (0.0693) | 1.96 (0.0772) | 2.16 (0.0850) |
| 17. INSPECT TOTAL PRELOAD |
![]() |
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
| 18. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION |
Remove the side bearing retainer and differential case assembly.
![]() |
Coat 3 or 4 teeth at 3 different positions on the ring gear with red lead.
Install the differential case assembly and side bearing retainer.
Hold the companion flange firmly and rotate the ring gear in both directions.
Remove the differential case, side bearing retainer and differential case assembly.
Inspect the tooth contact pattern.

![]() |
| Thickness mm (in.) | Thickness mm (in.) | Thickness mm (in.) |
| 1.70 (0.0669) | 1.94 (0.0764) | 2.18 (0.0858) |
| 1.73 (0.0681) | 1.97 (0.0776) | 2.21 (0.0870) |
| 1.76 (0.0693) | 2.00 (0.0787) | 2.24 (0.0882) |
| 1.79 (0.0705) | 2.03 (0.0799) | 2.27 (0.0894) |
| 1.82 (0.0717) | 2.06 (0.0811) | 2.30 (0.0906) |
| 1.85 (0.0728) | 2.09 (0.0823) | 2.33 (0.0917) |
| 1.88 (0.0740) | 2.12 (0.0835) | - |
| 1.91 (0.0752) | 2.15 (0.0847) | - |
![]() |
Using SST to hold the companion flange, remove the nut.
![]() |
Using SST, remove the companion flange.
![]() |
Using SST, remove the rear bearing from the drive pinion.
| 19. INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER |
Install a new bearing spacer and oil storage ring.
| 20. INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING |
| 21. INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER |
| 22. INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY FRONT |
Place the companion flange on the drive pinion.
Coat the threads of a new nut with hypoid gear oil LSD.
![]() |
Using SST and the companion flange, install the rear tapered roller bearing, then remove the companion flange.
| 23. INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL |
![]() |
Using SST and a hammer, install the oil seal.
Coat the oil seal lip with MP grease.
![]() |
Using SST to hold the flange, tighten the nut.
| 24. INSTALL DIFFERENTIAL SIDE BEARING RETAINER |
![]() |
Remove any old seal packing material and be careful not to drop oil on the contact surfaces of the differential carrier and side bearing retainer.
Clean the contact surfaces of any residual seal packing material using gasoline or alcohol.
Apply seal packing to the side bearing retainer, as shown.
Install the side bearing retainer with the 10 bolts.
Install the union.
| 25. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD |
![]() |
Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.
| Bearing | Standard |
| New | 0.98 to 1.57 N*m (10 to 16 kgf*cm, 8.7 to 13.9 in.*lbf) |
| Reused | 0.49 to 0.78 N*m (5 to 8 kgf*cm, 4.3 to 6.9 in.*lbf) |
| 26. INSPECT TOTAL PRELOAD |
![]() |
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
| 27. INSPECT BACKLASH DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION |
![]() |
Using SST and a dial indicator, measure the ring gear backlash.
If it is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.
| Thickness mm (in.) | Thickness mm (in.) | Thickness mm (in.) |
| 1.58 (0.0622) | 1.78 (0.0701) | 1.98 (0.0780) |
| 1.60 (0.0630) | 1.80 (0.0709) | 2.00 (0.0787) |
| 1.62 (0.0638) | 1.82 (0.0717) | 2.02 (0.0800) |
| 1.64 (0.0646) | 1.84 (0.0724) | 2.04 (0.0803) |
| 1.66 (0.0654) | 1.86 (0.0732) | 2.06 (0.0811) |
| 1.68 (0.0661) | 1.88 (0.0740) | 2.08 (0.0819) |
| 1.70 (0.0669) | 1.90 (0.0748) | 2.10 (0.0827) |
| 1.72 (0.0677) | 1.92 (0.0756) | 2.12 (0.0835) |
| 1.74 (0.0685) | 1.94 (0.0764) | 2.14 (0.0843) |
| 1.76 (0.0693) | 1.96 (0.0772) | 2.16 (0.0850) |
| 28. INSPECT AND ADJUST FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY FRONT |
![]() |
Using a dial indicator, measure the runout of the drive pinion companion flange vertically and horizontally.
| 29. INSTALL FRONT DRIVE PINION COMPANION FLANGE FRONT NUT |
![]() |
Using a chisel and hammer, stake the drive pinion nut.
| 30. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL |
![]() |
Using SST and a plastic hammer, install a new oil seal until its surface is flush with the differential carrier end.
Coat the oil seal lip with MP grease.
| 31. INSTALL DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY |
![]() |
Install a new snap ring onto the side gear inter shaft.
Using a plastic hammer, install the side gear inter shaft onto the differential case.
Check that there are 2 to 3 mm (0.08 to 0.12 in.) of play in the axial direction.
Check that the side gear inter shaft will not come out by trying to pull it completely out by hand.
| 32. INSTALL FRONT DIFFERENTIAL SIDE BEARING RETAINER DEFLECTOR |
![]() |
Using a brass bar and a hammer, install the side bearing retainer deflector.
| 33. INSTALL FRONT DIFFERENTIAL TUBE ASSEMBLY |
![]() |
Remove any old seal packing material and be careful not to drop oil on the contact surfaces of the differential and clutch case.
Clean the contact surfaces of any residual seal packing material using gasoline or alcohol.
Apply seal packing to the differential, as shown.
Install the differential tube into the differential carrier assembly.
![]() |
Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.
Apply adhesive to 2 to 3 threads of each bolt end.
Install the 4 bolts.
| 34. INSTALL DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY |
![]() |
Remove any old seal packing material and be careful not to drop oil on the contact surfaces of the actuator and clutch case.
Clean the contact surfaces of any residual seal packing material using gasoline or alcohol.
Apply seal packing to the differential tube, as shown.
![]() |
Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.
Install the actuator assembly onto the differential tube.
Apply adhesive to 2 to 3 threads of each bolt end.
Install the 4 bolts.