Home › DRIVE LINE › DIFFERENTIAL › DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock)

DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) > DISASSEMBLY

for Preparation Click here



1. FIX REAR DIFFERENTIAL CARRIER ASSEMBLY


C013829
  1. Fix the rear differential carrier assembly to the overattachment.



2. INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR


F001237E03
  1. Using a dial indicator, measure the runout of the companion flange vertically and horizontally.

    Maximum runout:
    Vertical runout: 0.10 mm (0.0039 in.)
    Lateral runout: 0.10 mm (0.0039 in.)

    If the runouts are not with the specifications, replace the companion flange.



3. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR


C014075
  1. Using a dial indicator, check the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.0028 in.)

    If the runout is greater than the maximum, replace the ring gear with a new one.



4. INSPECT DIFFERENTIAL RING GEAR BACKLASH


C028211
  1. Using a dial indicator, check the backlash of the ring gear.

    Backlash:
    0.13 to 0.18 mm (0.0051 to 0.0071 in.)

    If the backlash is not within the specification, adjust or repair the side bearing preload as necessary.



5. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


C003092
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Preload (at starting):
    0.56 to 0.85 N*m (5.7 to 8.7 kgf*cm, 5.0 to 7.5 in.*lbf)

    If necessary, disassemble and inspect the differential assembly.



6. INSPECT TOTAL PRELOAD


C003092
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

  1. Using a torque wrench, measure the total preload.

    Total preload (at starting):
    Drive pinion preload plus 0.39 to 0.59 N*m (4.0 to 6.0 kgf*cm, 3.5 to 5.2 in.*lbf)

    If necessary, disassemble and inspect the differential.



7. REMOVE DIFFERENTIAL LOCK SHIFT ACTUATOR


G020268
  1. Remove the 4 bolts and actuator from the differential carrier.

  1. Remove the O-ring.



8. REMOVE NO.1 TRANSFER INDICATOR SWITCH


G020269
  1. Remove the indicator switch and gasket.



9. REMOVE REAR DIFFERENTIAL LOCK SHIFT FORK SHAFT


G020270
  1. Using a 6 mm hexagon wrench, remove the 2 screw plugs.

  1. Remove the spring seat, spring and ball.



    G020271
  1. Using a 5 mm pin punch and hammer, remove the slotted pin.



    G020272
  1. Remove the 2 bolts from the shaft retainer.

  1. Using a plastic hammer, remove the shaft retainer.

  1. Remove the shift fork shaft.



10. REMOVE REAR DRIVE PINION NUT


F044346E02
  1. Using SST and a hammer, loosen the staked part of the nut.

    SST
    09930-00010  



    SA02349E06
  1. Using SST to hold the drive pinion companion flange, remove the nut.

    SST
    09330-00021  



11. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR


F052175E02
  1. Using SST, remove the drive pinion companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)



12. REMOVE REAR DIFFERENTIAL DUST DEFLECTOR


F040564E04
  1. Using SST and a press, remove the dust deflector.

    SST
    09950-60010   (09951-00380)
    09950-70010   (09951-07150)
    09950-00020  



13. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


SA02348E03
  1. Using SST, remove the oil seal from the differential carrier.

    SST
    09308-10010  



14. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


15. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


Z000641E04
  1. Using SST, remove the drive pinion tapered roller bearing from the drive pinion.

    SST
    09556-22010  



16. REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK


C030538
  1. Remove the 2 bolts and 2 rear differential bearing adjusting nut locks.



17. REMOVE DIFFERENTIAL CASE ASSEMBLY


F052179E01
  1. Place matchmarks on the bearing cap and differential carrier.

  1. Remove the 4 bolts and 2 differential bearing caps.

  1. Remove the 2 adjusting nuts.



    C028220
  1. Remove the rear differential case sub-assembly and 2 case bearings from the differential carrier.

    HINT:
    Tag the 2 case bearings outer races to show the locations for reassembly.



18. REMOVE DIFFERENTIAL DRIVE PINION


C030540
  1. Remove the differential drive pinion and bearing spacer from the differential carrier.



19. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


R010668E02
  1. Using SST and a press, remove the drive pinion tapered roller bearing from the drive pinion.

    SST
    09950-00020  

    HINT:
    If either the drive pinion or ring gear is damaged, replace them as a set.



20. REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER


21. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


F044358E02
  1. Using SST, remove the front tapered roller bearing from the carrier.

    SST
    09308-00010  

  1. Using a brass bar and a hammer, remove the oil storage ring from the carrier.



22. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


C091047
  1. Using a brass bar and a hammer, remove the rear tapered roller bearing from the carrier.



23. REMOVE DIFFERENTIAL RING GEAR


F052180E01
  1. Place matchmarks on the ring gear and differential case.

  1. Using a screwdriver and a hammer, unstake the lock plates.

  1. Remove the 10 ring gear set bolts and 5 lock plates.



    C014054
  1. Using a plastic hammer, tap on the ring gear to separate it from the differential case.



24. INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT


G020277
  1. Install the rear differential case bearing onto the differential case.

  1. Install the differential case onto the differential carrier.

  1. Install the 2 bearing caps and 4 bolts onto the differential carrier.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }

  1. Inspect the differential case runout.

    Maximum runout:
    0.07 mm (0.0028 in.)

  1. Remove the differential case.

  1. Remove the rear differential case bearing.



25. REMOVE REAR DIFFERENTIAL CASE BEARING


F040345E03
  1. Using SST, remove the 2 rear differential case bearings from the differential case.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00360)



26. DISASSEMBLE DIFFERENTIAL CASE


F052178E01
  1. Place matchmarks on the LH and RH cases.

  1. Remove the 8 bolts.



    ZK09094
  1. Using a plastic hammer, separate the LH and RH cases.



    C090324E02
  1. Remove these parts from the differential case.
    A
    Side gear
    B
    Side gear thrust washer
    C
    Spider
    D
    Pinion gear
    E
    Pinion gear thrust washer



27. INSPECT REAR DIFFERENTIAL LOCK SLEEVE


G020273
  1. Install the sleeve onto the differential case (LH) and check that it moves smoothly.

  1. Install the side gear onto the sleeve and check that it moves smoothly.



    G020274
  1. Using a feeler gauge, measure the clearance between the shift fork and sleeve.

    Maximum clearance:
    0.15 to 0.35 mm ( 0.0059 to 0.0138 in.)



28. INSPECT DIFFERENTIAL PINION AND SIDE GEAR
  1. Check that there is no damage to the differential pinion and differential side gear.
    If the differential pinion and/or differential side gear is damaged, replace the differential.



29. INSPECT DIFFERENTIAL CASE ASSEMBLY
  1. Check that the differential case is not damaged.
    If the differential case is damaged, replace the differential case.